In this circuit, the meter ECU receives engine coolant temperature signals from the ECM using the CAN communication system. The meter ECU displays an engine coolant temperature indication that is calculated based on the data received from the ECM.
If there is an open or short in the engine coolant temperature sensor circuit, the ECM stores the DTCs. Troubleshoot SFI System.
Click hereEngine / Hybrid System>2AR-FXE ENGINE CONTROL>SFI SYSTEM>DIAGNOSTIC TROUBLE CODE CHART
Check if CAN communication system DTCs are output.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM
| Result | Proceed to |
|---|---|
| DTCs are not output. | A |
| DTCs are output. | B |
A
B
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body / Combination Meter / Active Test.
Check the operation by referring to the table below.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Water Temperature Meter Operation | Engine coolant temperature receiver gauge | Low, Normal, High | - |
| Tester Display |
|---|
| Water Temperature Meter Operation |
Engine coolant temperature receiver gauge indication is normal.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check if SFI system DTCs are output.
Click hereEngine / Hybrid System>2AR-FXE ENGINE CONTROL>SFI SYSTEM>DIAGNOSIS SYSTEM
| Result | Proceed to |
|---|---|
| DTCs are not output. | A |
| DTCs are output. | B |
A
B
Click hereEngine / Hybrid System>2AR-FXE ENGINE CONTROL>SFI SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the intelligent tester on.
Enter the following menus:
for Engine and ECT: Powertrain / Engine and ECT / Data List.
for Combination Meter: Body / Combination Meter / Data List.
Check the values by referring to the table below.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Coolant Temp | Coolant temperature | Min.: -40°C (-40°F), Max.: 140°C (284°F) | 75 to 100°C (167 to 212°F): After warming up | ·
Stored as Freeze Frame Data ·
This is the engine coolant temperature. |
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Coolant Temperature | Engine coolant temperature | -40 to 140°C (-40 to 284°F) | After warming up: 75 to 100°C (167 to 212°F) | ·
If -40°C (-40°F): Sensor circuit open ·
If 140°C (284°F) or more: Sensor circuit shorted |
Enter inspection mode.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE
After warming up the engine, the engine coolant temperature is 75 to 100°C (167 to 212°F).
After a long soak, the engine coolant temperature, intake air temperature and ambient air temperature are approximately equal.
If the value is -40°C (-40°F), or 140°C (284°F), the sensor circuit is open or shorted.
Check if the engine overheats when the value indicates 140°C (284°F).
| Tester Display |
|---|
| Coolant Temp |
| Tester Display |
|---|
| Coolant Temperature |
| Result | Proceed to |
|---|---|
| The data list values of the ECUs match. | A |
| The data list values of the ECUs do not match. | B |
When the Data List values of the ECUs match, an internal malfunction of the combination meter assembly is suspected.
When the Data List values of the ECUs do not match, a signal output error of the skid control ECU or an internal malfunction of the combination meter assembly is suspected.
A
B