Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM
RM2040EQ _57 Power Source / Network _014721 NETWORKING _0075041 LIN COMMUNICATION SYSTEM C

NETWORKING  LIN COMMUNICATION SYSTEM  B2786  No Response from Steering Lock ECU  


DESCRIPTION

This DTC is stored when LIN communication between the certification ECU (smart key ECU assembly) and steering lock ECU (steering lock actuator assembly) stops for 10 seconds or more.

DTC No. Detection Item DTC Detection Condition Trouble Area
B2786 No Response from Steering Lock ECU No communication between steering lock ECU (steering lock actuator assembly) and certification ECU (smart key ECU assembly) for 10 seconds or more.
·

Steering lock ECU (steering lock actuator assembly)

·

Certification ECU (smart key ECU assembly)

·

Wire harness or connector

·

STRG LOCK fuse



WIRING DIAGRAM

B273275
0.885,2.479 2.521,3.052 1.635,0.573 10 false Certification ECU (Smart Key ECU Assembly) 3.771,2.448 5.646,3.198 1.875,0.75 10 false Steering Lock ECU (Steering Lock Actuator Assembly) 0.885,2.323 1.302,2.583 0.417,0.26 10 false I87 3.781,2.292 4.167,2.635 0.385,0.344 10 false I24 1.813,1.469 2.25,1.792 0.438,0.323 10 false LIN 4.25,1.469 4.656,1.813 0.406,0.344 10 false LIN 4.99,1.083 5.281,1.438 0.292,0.354 10 false B 4.771,1.99 5.229,2.385 0.458,0.396 10 false GND 4.302,0.396 5.833,0.688 1.531,0.292 10 false from Auxiliary Battery 0.667,3.469 2.667,3.802 2,0.333 10 false : LIN Communication Line 2.167,1.323 2.49,1.583 0.323,0.26 10 false 12 4.042,1.323 4.354,1.688 0.313,0.365 10 false 5 5.198,0.979 5.49,1.344 0.292,0.365 10 false 7 5.208,1.896 5.625,2.271 0.417,0.375 10 false 1 5.448,1.229 6.469,1.521 1.021,0.292 10 false STRG LOCK

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

If the certification ECU (smart key ECU assembly) is replaced, register the keys (refer to the Service Bulletin).

·

If the steering lock ECU (steering lock actuator assembly) is replaced, register the ECU code (refer to the Service Bulletin).

·

When using the intelligent tester to troubleshoot with the power switch off:

Connect the intelligent tester to the DLC3, and turn the courtesy switch on and off at 1.5-second intervals until communication between the intelligent tester and vehicle begins.



PROCEDURE

1.CHECK DTC OUTPUT
a.

Clear the DTC.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Entry&Start > Clear DTCs
50002 125

b.

Recheck for DTCs.

Body Electrical > Entry&Start > Trouble Codes
50001 125
OK:

DTC B2786 is not output.



Result:
Result Proceed to
Only B2786 is output A
DTC B2786 and B2785 are output simultaneously B


HINT:

When DTC B2786 and B2785 are output simultaneously, perform troubleshooting for DTC B2785 first.



A

2.CHECK HARNESS AND CONNECTOR (STEERING LOCK ECU - AUXILIARY BATTERY AND BODY GROUND)

B

2.CHECK HARNESS AND CONNECTOR (STEERING LOCK ECU - AUXILIARY BATTERY AND BODY GROUND)
a.

Disconnect the I24 steering lock ECU (steering lock actuator assembly) connector.


b.

Measure the resistance and voltage according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I24-1 (GND) - Body ground Always Below 1 Ω


Standard Voltage:
Tester Connection Condition Specified Condition
I24-7 (B) - Body ground Power switch off 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - STEERING LOCK ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - STEERING LOCK ECU)
a.

Disconnect the I87 certification ECU (smart key ECU assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I87-12 (LIN) - I24-5 (LIN) Always Below 1 Ω
I87-12 (LIN) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY)
a.

Replace the steering lock ECU (steering lock actuator assembly).

Click hereSteering>STEERING COLUMN>STEERING COLUMN ASSEMBLY>REMOVAL


Result:
Proceed to
NEXT



NEXT

5.CHECK DTC OUTPUT
5.CHECK DTC OUTPUT
a.

Clear the DTC.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Entry&Start > Clear DTCs
50002 125

b.

Recheck for DTCs.

Body Electrical > Entry&Start > Trouble Codes
50001 125
OK:

DTC B2786 is not output.



Result:
Proceed to
OK
NG



OK

END (STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY) WAS DEFECTIVE)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)