The automatic light control sensor detects the ambient light. The sensor creates an electrical signal based on the amount of light, and sends the signal to the main body ECU (multiplex network body ECU). The main body ECU (multiplex network body ECU) turns on or off the headlights and taillights according to the signal.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B1244 | Light Sensor Circuit Malfunction | ·
Malfunction in automatic light control sensor ·
Open or short in automatic light control sensor circuit |
·
Automatic light control sensor ·
Harness or connector ·
Main body ECU (multiplex network body ECU) |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body / Main Body / Data List.
Read the display on the intelligent tester.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Illumination Rate Info | Illumination rate information | 0.00 ms. to 2162.65 ms. | Value is output according to ambient light levels | - |
| Tester Display |
|---|
| Illumination Rate Info |
Normal condition listed above is displayed.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the I61 automatic light control sensor connector.
Disconnect the I13 main body ECU (multiplex network body ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I13-22 (CLTE) - I61-3 (CLTE) | Always | Below 1 Ω |
| I13-21 (CLTS) - I61-5 (CLTS) | Always | Below 1 Ω |
| I13-20 (CLTB) - I61-6 (CLTB) | Always | Below 1 Ω |
| I13-22 (CLTE) - Body ground | Always | 10 kΩ or higher |
| I13-21 (CLTS) - Body ground | Always | 10 kΩ or higher |
| I13-20 (CLTB) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected
(Main Body ECU (Multiplex Network Body ECU)) |
Reconnect the I13 main body ECU (multiplex network body ECU) connector.
Measure the voltage and resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I13-20 (CLTB) - I13-22 (CLTE) | Power switch off | Below 1 V |
| Power switch on (IG) | 11 to 14 V |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I13-22 (CLTE) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected
(Automatic Light Control Sensor) |
Reconnect the I61 automatic light control sensor connector.
Connect an oscilloscope to the automatic light control sensor connector.
Check the waveform.
| Tester Connection | Tool Setting | Condition | Specified Condition |
|---|---|---|---|
| I61-3 (CLTE) - I61-5 (CLTS) | 5 V/DIV., 5 ms./DIV. | Power switch on (IG), light control switch in AUTO position | Correct waveform is as shown |
If the ambient light becomes brighter, width A becomes narrower.
| Proceed to |
|---|
| OK |
| NG |
OK
NG