When the driving support ECU assembly receives an electronically controlled brake system malfunction signal from the skid control ECU (brake booster with master cylinder assembly) via CAN communication, DTC C1A50 is stored.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C1A50 | Brake System | When the dynamic radar cruise control system is operating, the input malfunction signal from the brake booster with master cylinder assembly continues for 0.272 seconds or more while the vehicle is being driven at a speed of 36 km/h (22 mph) or more. | ·
Electronically controlled brake system ·
Driving support ECU assembly |
When replacing the driving support ECU assembly, always replace it with a new one. If a driving support ECU assembly which was installed to another vehicle is used, the information stored in the driving support ECU assembly will not match the information from the vehicle. As a result, a DTC may be stored.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Chassis / ABS/VSC/TRC / Trouble Codes.
Check for DTCs.
| Result | Proceed to |
|---|---|
| Electronically controlled brake system DTCs are not output | A |
| Electronically controlled brake system DTCs are output | B |
A
B
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Clear the DTCs.
Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR
Perform the following to make sure that the DTC detection conditions are met.
If the detection conditions are not met, the malfunction cannot be detected.
Drive the vehicle at a speed for which dynamic radar cruise control system operation is possible.
Turn the cruise control system on using the cruise control main switch (ON-OFF button).
Push the cruise control main switch to -/SET to begin control of vehicle speed using the cruise control system.
Check for DTCs.
Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC C1A50 is not output | A |
| DTC C1A50 is output | B |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
Replace the driving support ECU assembly.
Click hereEngine / Hybrid System>CRUISE CONTROL>DRIVING SUPPORT ECU>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Clear the DTCs.
Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR
Perform the following to make sure that the DTC detection conditions are met.
If the detection conditions are not met, the malfunction cannot be detected.
Drive the vehicle at a speed for which dynamic radar cruise control system operation is possible.
Turn the cruise control system on using the cruise control main switch (ON-OFF button).
Push the cruise control main switch to -/SET to begin control of vehicle speed using the cruise control system.
Check for DTCs.
Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC C1A50 is not output | A |
| DTC C1A50 is output | B |
A
B
Replace the skid control ECU (brake booster with master cylinder assembly) with a new one.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Clear the DTCs.
Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR
Perform the following to make sure that the DTC detection conditions are met.
If the detection conditions are not met, the malfunction cannot be detected.
Drive the vehicle at a speed for which dynamic radar cruise control system operation is possible.
Turn the cruise control system on using the cruise control main switch (ON-OFF button).
Push the cruise control main switch to -/SET to begin control of vehicle speed using the cruise control system.
Check for DTCs.
Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC C1A50 is not output | A |
| DTC C1A50 is output | B |
A
B