When the lane departure warning camera is replaced with a new one, it acquires the country specification information from the main body ECU (multiplex network body ECU) or power management control ECU. If the lane departure warning camera cannot store the country specification information, DTC C1AAA or C1AAD is stored.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C1AAA | FCM Destination Information Uninitialized | While the power switch is on (IG), the lane departure warning camera cannot store the country specification information. | ·
Main body ECU (Multiplex network body ECU) ·
Lane departure warning camera |
| C1AAD | Vehicle Information Initialization Incomplete | When the power switch is turned on (IG) or the system is activated, the vehicle information from the power management control ECU cannot be confirmed. | ·
Power management control ECU ·
Lane departure warning camera |
When the lane departure warning camera is replaced with a new one, adjustment of the lane departure warning camera axis must be performed
Click hereEngine / Hybrid System>CRUISE CONTROL>LANE RECOGNITION CAMERA SENSOR>ADJUSTMENT
When replacing the lane departure warning camera, always replace it with a new one. If a lane departure warning camera which was installed to another vehicle is used, the information stored in the lane departure warning camera will not match the information from the vehicle. As a result, a DTC may be stored.
The lane departure alert system uses the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshooting the lane departure alert system after confirming that the communication systems are functioning properly.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Chassis / Lane Departure Alert / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Destination Information | Status of the country | JPN, NA, EURO, CHINA or OTHER (GEN-EXP) | Actual country code | - |
| Tester Display |
|---|
| Destination Information |
| Result | Proceed to |
|---|---|
| Country specification information for vehicle and lane departure warning camera match | A |
| Country specification information for vehicle and lane departure warning camera do not match | B |
A
B
Clear the DTCs.
Click hereEngine / Hybrid System>CRUISE CONTROL>LANE DEPARTURE ALERT SYSTEM>DTC CHECK / CLEAR
Make sure that the DTC detection conditions are met.
If the detection conditions are not met, the system cannot detect the malfunction.
Check for DTCs.
Click hereEngine / Hybrid System>CRUISE CONTROL>LANE DEPARTURE ALERT SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC C1AAA and C1AAD are not output | A |
| DTC C1AAA or C1AAD is output | B |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
Replace the lane departure warning camera with a new one.
Click hereEngine / Hybrid System>CRUISE CONTROL>LANE RECOGNITION CAMERA SENSOR>REMOVAL
Perform the lane departure warning camera adjustment.
Click hereEngine / Hybrid System>CRUISE CONTROL>LANE RECOGNITION CAMERA SENSOR>ADJUSTMENT
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Click hereEngine / Hybrid System>CRUISE CONTROL>LANE DEPARTURE ALERT SYSTEM>DTC CHECK / CLEAR
Make sure that the DTC detection conditions are met.
If the detection conditions are not met, the system cannot detect the malfunction.
Check for DTCs.
Click hereEngine / Hybrid System>CRUISE CONTROL>LANE DEPARTURE ALERT SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC C1AAA and C1AAD are not output | A |
| DTC C1AAA is output | B |
| DTC C1AAD is output | C |
A
B
C
Replace the main body ECU (multiplex network body ECU) with a new one.
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Click hereEngine / Hybrid System>CRUISE CONTROL>LANE DEPARTURE ALERT SYSTEM>DTC CHECK / CLEAR
Make sure that the DTC detection conditions are met.
If the detection conditions are not met, the system cannot detect the malfunction.
Check for DTCs.
Click hereEngine / Hybrid System>CRUISE CONTROL>LANE DEPARTURE ALERT SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC C1AAA and C1AAD are not output | A |
| DTC C1AAA is output | B |
| DTC C1AAD is output | C |
A
B
C
Replace the power management control ECU with a new one.
Click herePower Source / Network>POWER DISTRIBUTION>POWER MANAGEMENT CONTROL ECU>COMPONENTS
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Click hereEngine / Hybrid System>CRUISE CONTROL>LANE DEPARTURE ALERT SYSTEM>DTC CHECK / CLEAR
Make sure that the DTC detection conditions are met.
If the detection conditions are not met, the system cannot detect the malfunction.
Check for DTCs.
Click hereEngine / Hybrid System>CRUISE CONTROL>LANE DEPARTURE ALERT SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC C1AAD is not output | A |
| DTC C1AAD is output | B |
A
B