Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID BATTERY SYSTEM › from 2015.04
RM2040EQ _51 Engine / Hybrid System _014692 HYBRID / BATTERY CONTROL _0074886 HYBRID BATTERY SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID BATTERY SYSTEM  P0A9C-123  Hybrid Battery Temperature Sensor "A" Range / Performance  P0AC6-123  Hybrid Battery Temperature Sensor "B" Range / Performance  P0ACB-123  Hybrid Battery Temperature Sensor "C" Range / Performance  P3065-123  Hybrid Battery Temperature Sensor Range/Performance Stuck "A"  


DESCRIPTION

The battery temperature sensors are provided at 3 locations of the HV battery. The resistance of the thermistor, which is built into each battery temperature sensor, varies in accordance with changes in the HV battery temperature. The lower the battery temperature, the higher the thermistor resistance. Conversely, the higher the temperature, the lower the resistance. The battery smart unit uses the battery temperature sensors to detect the HV battery temperature, and sends the detected value to the power management control ECU. Based on the results of this detection, the power management control ECU controls the blower fan. (The blower fan starts when HV battery temperature rises above a predetermined level.)

Temperature Sensor Identification Cross Reference Table:
DTC Title Sensor Battery Temperature Sensor Intelligent Tester Display
A 0 1
B 1 2
C 2 3


HINT:

For example, sensor A in the DTC title is battery temperature sensor (No. 0). This sensor is displayed as Temp of Batt TB1 in the Data List.


A171806E11
1.781,0.031 2.51,0.271 0.729,0.24 10 false Reference: 2.167,0.354 2.427,0.5 0.26,0.146 10 false 250 2.167,0.677 2.427,0.823 0.26,0.146 10 false 200 2.167,0.979 2.427,1.125 0.26,0.146 10 false 150 2.177,1.271 2.438,1.417 0.26,0.146 10 false 100 2.25,1.583 2.438,1.729 0.188,0.146 10 false 50 2.333,1.896 2.438,2.042 0.104,0.146 10 false 0 3.271,2.25 3.375,2.396 0.104,0.146 10 false 0 2.573,2.25 2.802,2.417 0.229,0.167 10 false -40 2.917,2.25 3.146,2.417 0.229,0.167 10 false -20 3.521,2.25 3.698,2.417 0.177,0.167 10 false 20 3.813,2.25 3.99,2.417 0.177,0.167 10 false 40 4.094,2.25 4.271,2.417 0.177,0.167 10 false 60 4.396,2.25 4.573,2.417 0.177,0.167 10 false 80 4.646,2.25 4.906,2.417 0.26,0.167 10 false 100 3.177,2.458 3.448,2.604 0.271,0.146 10 false (32) 2.531,2.448 2.865,2.615 0.333,0.167 10 false (-40) 2.906,2.448 3.167,2.615 0.26,0.167 10 false (-4) 3.458,2.448 3.729,2.615 0.271,0.167 10 false (68) 3.708,2.448 4.073,2.615 0.365,0.167 10 false (104) 4.031,2.448 4.375,2.615 0.344,0.167 10 false (140) 4.354,2.448 4.708,2.615 0.354,0.167 10 false (176) 4.677,2.448 5.021,2.615 0.344,0.167 10 false (212) 5.094,2.24 5.365,2.438 0.271,0.198 10 false (°C) 5.094,2.448 5.427,2.646 0.333,0.198 10 false (°F) 1.823,0.375 2.115,0.573 0.292,0.198 10 false (kΩ) 1.406,0.573 2.135,0.76 0.729,0.188 10 false Resistance 5.458,2.24 6.802,2.427 1.344,0.188 10 false Battery Temperature 2.51,0.042 5.615,0.313 3.104,0.271 10 false Battery Temperature Sensor Characteristic Graph

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P0A9C-123 Hybrid Battery Temperature Sensor "A" Range / Performance When the battery temperature sensor performance is abnormal (1 trip detection / 2 trip detection)
·

HV battery

·

Battery smart unit

·

Wire harness or connector


Comes on Master Warning Light:
Comes on
P0AC6-123 Hybrid Battery Temperature Sensor "B" Range / Performance When the battery temperature sensor performance is abnormal (1 trip detection / 2 trip detection)
·

HV battery

·

Battery smart unit

·

Wire harness or connector


Comes on Master Warning Light:
Comes on
P0ACB-123 Hybrid Battery Temperature Sensor "C" Range / Performance When the battery temperature sensor performance is abnormal (1 trip detection / 2 trip detection)
·

HV battery

·

Battery smart unit

·

Wire harness or connector


Comes on Master Warning Light:
Comes on
P3065-123 Hybrid Battery Temperature Sensor Range/Performance Stuck "A" When the battery temperature sensor performance is abnormal (1 trip detection / 2 trip detection)
·

HV battery

·

Battery smart unit

·

Wire harness or connector


Comes on Master Warning Light:
Comes on

WIRING DIAGRAM

A260750E20
0.594,2.292 1.365,2.677 0.771,0.385 10 false IGCT-MAIN 1.26,1.427 1.656,1.625 0.396,0.198 10 false IGCT 4.01,0.938 4.958,1.135 0.948,0.198 10 false BATT VL SSR 5.625,0.802 6.208,1 0.583,0.198 10 false IGCT 5.26,0.802 5.563,1 0.302,0.198 10 false N18 5.333,0.604 5.469,0.781 0.135,0.177 10 false 3 5.625,2.354 6.042,2.552 0.417,0.198 10 false TCO 5.615,2.833 6.031,3.031 0.417,0.198 10 false GCO 5.615,3.208 6.031,3.406 0.417,0.198 10 false TBO 5.604,3.688 6.021,3.885 0.417,0.198 10 false GBO 5.615,4.052 6.031,4.25 0.417,0.198 10 false TB1 5.615,4.531 6.031,4.729 0.417,0.198 10 false GB1 5.625,4.906 6.042,5.104 0.417,0.198 10 false TB2 5.625,5.385 6.042,5.583 0.417,0.198 10 false GB2 5.604,6.042 6.01,6.229 0.406,0.188 10 false GND 5.25,6.042 5.563,6.24 0.313,0.198 10 false N18 5.333,5.833 5.469,6.01 0.135,0.177 10 false 6 5.333,5.323 5.521,5.5 0.188,0.177 10 false 8 5.333,4.844 5.5,5.031 0.167,0.188 10 false 2 5.333,4.448 5.531,4.625 0.198,0.177 10 false 9 5.344,3.979 5.479,4.156 0.135,0.177 10 false 3 5.292,3.594 5.5,3.771 0.208,0.177 10 false 10 5.354,3.125 5.563,3.302 0.208,0.177 10 false 4 5.354,2.719 5.563,2.896 0.208,0.177 10 false 7 5.365,2.229 5.573,2.406 0.208,0.177 10 false 1 2.115,1.625 2.417,1.885 0.302,0.26 10 false A38 2.74,1.063 2.865,1.229 0.125,0.167 10 false 4 1.802,0.677 1.969,0.906 0.167,0.229 10 false 5 1.792,1.063 1.969,1.313 0.177,0.25 10 false 1 1.063,1.052 1.229,1.313 0.167,0.26 10 false 2 1.052,0.688 1.26,0.917 0.208,0.229 10 false 3 2.417,1.625 4.51,1.948 2.094,0.323 10 false Power Management Control ECU 2.865,6.021 3.604,6.563 0.74,0.542 10 false HV Battery 5.302,2.448 5.573,2.646 0.271,0.198 10 false z8 5.281,2.938 5.552,3.135 0.271,0.198 10 false z8 5.292,3.302 5.563,3.5 0.271,0.198 10 false z8 5.302,3.771 5.573,3.969 0.271,0.198 10 false z8 5.292,4.156 5.563,4.354 0.271,0.198 10 false z8 5.292,4.646 5.563,4.844 0.271,0.198 10 false z8 5.292,5.021 5.563,5.219 0.271,0.198 10 false z8 5.292,5.5 5.563,5.698 0.271,0.198 10 false z8 2.333,3.479 4.281,3.792 1.948,0.313 10 false Battery Temperature Sensor 0 2.323,4.333 4.271,4.646 1.948,0.313 10 false Battery Temperature Sensor 1 2.333,5.198 4.281,5.51 1.948,0.313 10 false Battery Temperature Sensor 2 2.313,2.635 4.208,2.906 1.896,0.271 10 false Inlet Air Temperature Sensor 5.563,6.448 6.74,6.813 1.177,0.365 10 false Battery Smart Unit 2.958,1.198 3.385,1.396 0.427,0.198 10 false MREL 0.615,3.156 1.323,3.531 0.708,0.375 10 false R/B NO. 2 0.604,4.083 1.177,4.427 0.573,0.344 10 false MAIN 0.74,5.656 1.802,6.063 1.063,0.406 10 false Auxiliary Battery 4.208,0.635 4.417,0.813 0.208,0.177 10 false 1 4.594,0.635 4.833,0.833 0.24,0.198 10 false 2 0.271,2.448 0.448,2.698 0.177,0.25 10 false 1 0.271,2.104 0.438,2.365 0.167,0.26 10 false 2

CAUTION / NOTICE / HINT

CAUTION:
·

Before inspecting the high-voltage system, take safety precautions to prevent electrical shocks, such as wearing insulated gloves and removing the service plug grip. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·

After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>PRECAUTION

HINT:

At least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.


·

When disposing of an HV battery, make sure to return it through an authorized collection agent who is capable of handling it safely. If the HV battery is returned via the manufacturer specified route, it will be returned properly and in a safe manner by an authorized collection agent.



NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

1.CHECK DTC OUTPUT (HYBRID CONTROL)

A

2.CHECK HV BATTERY (BATTERY TEMPERATURE SENSOR)

B

2.CHECK HV BATTERY (BATTERY TEMPERATURE SENSOR)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the luggage compartment front trim cover.

Click hereVehicle Exterior>DOOR / HATCH>LUGGAGE DOOR HINGE TORSION BAR>REMOVAL


c.

Remove the rear side seatback assembly LH.

Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY>REMOVAL


d.

Disconnect connectors z8 and N18 from the battery smart unit.


e.
A260171C05
1.542,1.115 1.917,1.406 0.375,0.292 1.646,2.031 0.844,1.469 true 2.25,1.281 1.781,2.021 true 2.688,1.75 1.927,2.052 true 2.552,2.49 1.917,2.198 true 2.094,2.708 1.792,2.188 true 1.656,2.177 1.021,2.552 true 0.719,0.25 1.01,0.5 0.292,0.25 10 false *a 2.75,1.667 3.177,1.927 0.427,0.26 10 false TB2 2.229,1.104 2.688,1.333 0.458,0.229 10 false TB1 0.604,1.292 0.958,1.479 0.354,0.188 10 false TBO 0.823,2.594 1.24,2.823 0.417,0.229 10 false GBO 2.021,2.75 2.49,2.979 0.469,0.229 10 false GB1 2.615,2.448 3.042,2.688 0.427,0.24 10 false GB2 1.656,1.188 1.938,1.406 0.281,0.219 10 false z8
*a Rear view of wire harness connector
(to Battery Smart Unit)


Measure the resistance of the circuit for the malfunctioning sensor (battery temperature sensor 0 to 2).

Tester Connection:
Tester Connection Battery Temperature Sensor No.
z8-4 (TBO) - z8-10 (GBO) 0
z8-3 (TB1) - z8-9 (GB1) 1
z8-2 (TB2) - z8-8 (GB2) 2


Standard Resistance:
Thermistor Temperature Switch Condition Specified Condition
0°C (32°F) Power switch off 26.7 to 27.8 kΩ
25°C (77°F) Power switch off 9.9 to 10.1 kΩ
40°C (104°F) Power switch off 5.73 to 5.92 kΩ



f.
A244309C25
0.823,1.656 1.25,1.948 0.427,0.292 0.531,3.385 0.958,3.656 0.427,0.271 1.521,2.292 1.094,2.167 true 2.135,4.458 1.885,4.146 true 2.531,3.552 1.896,3.969 true 2.396,3.302 1.792,3.969 true 1.063,3.948 1.635,3.979 true 1.104,4.292 1.635,4.125 true 1.323,4.49 1.771,4.135 true 2.531,3.875 2.031,4.01 true 2.542,4.167 2.021,4.135 true 1.521,2.438 1.094,2.573 true 0.177,0.125 0.448,0.302 0.271,0.177 10 false *a 0.74,2.094 1.135,2.333 0.396,0.24 10 false IGCT 0.75,3.865 1.094,4.073 0.344,0.208 10 false TBO 2.458,3.198 2.792,3.406 0.333,0.208 10 false TB1 2.604,3.469 2.906,3.677 0.302,0.208 10 false TB2 0.74,4.208 1.094,4.406 0.354,0.198 10 false GBO 1.031,4.438 1.365,4.625 0.333,0.188 10 false GB1 2.177,4.417 2.49,4.594 0.313,0.177 10 false GB2 2.583,3.813 2.958,4 0.375,0.188 10 false TCO 2.583,4.115 2.958,4.323 0.375,0.208 10 false GCO 0.885,1.688 1.188,1.885 0.302,0.198 10 false N18 0.667,3.406 0.896,3.583 0.229,0.177 10 false z8 0.75,2.51 1.146,2.75 0.396,0.24 10 false GND
*a Rear view of wire harness connector
(to Battery Smart Unit)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
z8-4 (TBO) - N18-3 (IGCT) Power switch off 10 kΩ or higher
z8-4 (TBO) - N18-6 (GND) Power switch off 10 kΩ or higher
z8-10 (GBO) - N18-3 (IGCT) Power switch off 10 kΩ or higher
z8-10 (GBO) - N18-6 (GND) Power switch off 10 kΩ or higher
z8-3 (TB1) - N18-3 (IGCT) Power switch off 10 kΩ or higher
z8-3 (TB1) - N18-6 (GND) Power switch off 10 kΩ or higher
z8-9 (GB1) - N18-3 (IGCT) Power switch off 10 kΩ or higher
z8-9 (GB1) - N18-6 (GND) Power switch off 10 kΩ or higher
z8-2 (TB2) - N18-3 (IGCT) Power switch off 10 kΩ or higher
z8-2 (TB2) - N18-6 (GND) Power switch off 10 kΩ or higher
z8-8 (GB2) - N18-3 (IGCT) Power switch off 10 kΩ or higher
z8-8 (GB2) - N18-6 (GND) Power switch off 10 kΩ or higher
z8-1 (TCO) - N18-3 (IGCT) Power switch off 10 kΩ or higher
z8-1 (TCO) - N18-6 (GND) Power switch off 10 kΩ or higher
z8-7 (GCO) - N18-3 (IGCT) Power switch off 10 kΩ or higher
z8-7 (GCO) - N18-6 (GND) Power switch off 10 kΩ or higher



g.

Connect the battery smart unit connectors.


h.

Install the rear side seatback assembly LH.


i.

Install the luggage compartment front trim cover.


Result:
Proceed to
OK
NG



OK

NG

3.CHECK HARNESS AND CONNECTOR (BATTERY TEMPERATURE SENSOR)
3.CHECK HARNESS AND CONNECTOR (BATTERY TEMPERATURE SENSOR)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the luggage compartment front trim cover.

Click hereVehicle Exterior>DOOR / HATCH>LUGGAGE DOOR HINGE TORSION BAR>REMOVAL


c.

Check the wire harness and connectors of the battery temperature sensor for abnormalities by sight and touch.

Specified Condition:

There are no open or short circuits in the wire harness and connectors. There are no short circuits to other wire harnesses.


HINT:

Because the battery harness is not available as a supply part, if the harness cannot be repaired, replace the HV battery.



d.

Install the luggage compartment front trim cover.


Result:
Proceed to
OK
NG



OK

NG

REPAIR HARNESS OR CONNECTOR