Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › 2014.05–2015.04
RM2040EQ _57 Power Source / Network _014721 NETWORKING _0075042 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Check CAN Bus Line for Short to +B  


DESCRIPTION

There may be a short circuit between one of the CAN bus lines and +B when no resistance exists between terminals 6 (CANH) and 16 (BAT) or 14 (CANL) and 16 (BAT) of the DLC3.

Symptom Trouble Area
No resistance exists between terminals 6 (CANH) and 16 (BAT) or 14 (CANL) and 16 (BAT) of the DLC3.
·

Short to +B in CAN main bus line

·

Short to +B in CAN branch line

·

Power management control ECU

·

ECM

·

Main body ECU (Multiplex network body ECU)

·

Combination meter assembly

·

Brake booster with master cylinder assembly (Skid control ECU)

·

Steering sensor

·

Power steering ECU assembly

·

Airbag sensor assembly

·

Air conditioning amplifier assembly

·

Smart key ECU assembly (Certification ECU)

·

Navigation ECU sub-assembly*1

·

Radio and display receiver assembly*2

·

Headlight swivel ECU assembly (AFS ECU)*3

·

Navigation receiver assembly*4

·

CAN junction LH1 connector

·

CAN junction RH1 connector



·

*1: for Navigation Receiver Type with HDD

·

*2: for Radio and Display Type

·

*3: w/ Automatic High Beam System

·

*4: for Navigation Receiver Type without HDD


WIRING DIAGRAM

C259932E03
3.969,7.979 5.76,8.25 1.792,0.271 10 false : CAN Branch Line (CANH) 3.958,8.396 5.688,8.583 1.729,0.188 10 false : CAN Branch Line (CANL) 0.833,8 2.75,8.188 1.917,0.188 10 false : CAN Main Bus Line (CANH) 0.833,8.406 2.75,8.594 1.917,0.188 10 false : CAN Main Bus Line (CANL) 3.469,0.354 3.885,0.542 0.417,0.188 10 false 120 Ω 2.813,1 3.365,1.24 0.552,0.24 10 false CANL 1.083,4.406 1.521,4.656 0.438,0.25 10 false CANL 0.417,0.594 0.781,0.76 0.365,0.167 10 false I18 4.125,1.625 4.333,1.854 0.208,0.229 10 false R 2.198,4.49 2.448,4.802 0.25,0.313 10 false W 2.229,5.469 2.469,5.729 0.24,0.26 10 false L 2.198,6.219 2.406,6.448 0.208,0.229 10 false W 5.188,5.198 5.417,5.521 0.229,0.323 10 false W 3.021,1.615 3.292,1.917 0.271,0.302 10 false W 4.135,6.979 4.396,7.24 0.26,0.26 10 false B 3.021,6.979 3.344,7.281 0.323,0.302 10 false W 0.146,4.698 0.521,5.052 0.375,0.354 10 false I30 0.708,0.594 2.688,0.979 1.979,0.385 10 false Combination Meter Assembly 4.104,1.01 4.635,1.302 0.531,0.292 10 false CANH 1.063,3.823 1.573,4.083 0.51,0.26 10 false CANH 1.083,6.146 1.625,6.417 0.542,0.271 10 false CANL 1.073,5.552 1.625,5.833 0.552,0.281 10 false CANH 6.063,4.969 6.594,5.219 0.531,0.25 10 false CANL 5.896,4.604 6.406,4.854 0.51,0.25 10 false CANH 4.083,1.26 4.375,1.542 0.292,0.281 10 false 16 2.698,5.469 2.938,5.698 0.24,0.229 10 false 1 2.708,6.208 2.938,6.438 0.229,0.229 10 false 2 2.719,3.76 2.938,3.958 0.219,0.198 10 false 1 2.719,4.469 2.927,4.635 0.208,0.167 10 false 2 2.698,2.031 2.969,2.292 0.271,0.26 10 false 1 2.708,2.76 2.979,3 0.271,0.24 10 false 2 1.552,3.844 1.854,4.135 0.302,0.292 10 false 3 1.552,4.406 1.823,4.656 0.271,0.25 10 false 2 4.479,4.469 4.719,4.688 0.24,0.219 10 false 1 4.479,5.188 4.729,5.438 0.25,0.25 10 false 2 2.219,3.75 2.479,3.969 0.26,0.219 10 false V 2.938,1.844 3.146,2.125 0.208,0.281 10 false 2 3.052,1.26 3.375,1.542 0.323,0.281 10 false 15 4.281,1.844 4.531,2.115 0.25,0.271 10 false 1 2.927,6.688 3.167,6.969 0.24,0.281 10 false 2 4.26,6.688 4.521,6.917 0.26,0.229 10 false 1 1.563,6.135 1.833,6.375 0.271,0.24 10 false 2 1.552,5.552 1.813,5.802 0.26,0.25 10 false 1 5.833,5.135 6.115,5.396 0.281,0.26 10 false 14 5.656,4.542 5.875,4.75 0.219,0.208 10 false 6 5.177,0.448 6.604,0.781 1.427,0.333 10 false x: Suspected Area 6.135,5.208 6.531,5.552 0.396,0.344 10 false I39 6.385,5.208 6.854,5.563 0.469,0.354 10 false DLC3 0.438,4.698 1.563,5.052 1.125,0.354 10 false Steering Sensor 1.094,2.698 1.573,2.938 0.479,0.24 10 false CA1L 2.302,2.76 2.542,3.031 0.24,0.271 10 false W 0.104,2.969 0.469,3.135 0.365,0.167 10 false A28 1.063,2.104 1.542,2.344 0.479,0.24 10 false CA1H 1.521,2.115 1.823,2.375 0.302,0.26 10 false 37 1.521,2.667 1.823,2.917 0.302,0.25 10 false 38 2.323,2.042 2.542,2.26 0.219,0.219 10 false Y 0.396,2.969 2.583,3.375 2.188,0.406 10 false Brake Booster with Master Cylinder Assembly (Skid Control ECU) 4.573,2.042 6.75,2.406 2.177,0.365 10 false CAN Junction RH1 Connector 0.177,6.406 0.448,6.563 0.271,0.156 10 false I87 0.427,6.406 2.073,6.896 1.646,0.49 10 false Smart Key ECU Assembly (Certification ECU) 5.208,4.458 5.385,4.719 0.177,0.26 10 false G 2.625,6.021 3.031,6.302 0.406,0.281 10 false I106 2.615,5.656 3.052,5.958 0.438,0.302 10 false I106 2.677,4.292 2.969,4.531 0.292,0.24 10 false I97 2.677,3.927 3.063,4.219 0.385,0.292 10 false I97 2.625,2.219 3.031,2.552 0.406,0.333 10 false I110 2.625,2.573 3.031,2.875 0.406,0.302 10 false I110 3.177,1.854 3.479,2.115 0.302,0.26 10 false I94 3.938,1.854 4.25,2.156 0.313,0.302 10 false I94 4.438,4.646 4.781,4.958 0.344,0.313 10 false I96 4.438,5 4.781,5.292 0.344,0.292 10 false I96 3.146,6.677 3.583,6.938 0.438,0.26 10 false I101 3.906,6.677 4.333,6.969 0.427,0.292 10 false I101 1.729,2.76 1.979,3.052 0.25,0.292 10 false W 1.708,2.042 2.104,2.271 0.396,0.229 10 false GR 4.479,2.719 4.75,2.969 0.271,0.25 10 false 1 4.479,3.458 4.74,3.708 0.26,0.25 10 false 2 5.833,3.396 6.375,3.646 0.542,0.25 10 false MPX2 5.406,3.479 5.646,3.708 0.24,0.229 10 false W 4.781,3.729 5.219,4 0.438,0.271 10 false A35 5.823,2.823 6.313,3.031 0.49,0.208 10 false MPX1 5.594,2.823 5.896,3.083 0.302,0.26 10 false 12 5.594,3.375 5.833,3.594 0.24,0.219 10 false 13 5.417,2.75 5.677,3 0.26,0.25 10 false B 5.115,3.719 7.115,4.344 2,0.625 10 false Headlight Swivel ECU Assembly (AFS ECU)* 4.406,2.917 4.865,3.26 0.458,0.344 10 false I112 4.406,3.281 4.781,3.531 0.375,0.25 10 false I112 4.833,3.479 5.021,3.708 0.188,0.229 10 false W 4.823,2.75 5.229,3.031 0.406,0.281 10 false BE 0.25,7.563 2.844,7.844 2.594,0.281 10 false *: w/ Automatic High Beam System

C261916E03
0.833,9.052 2.802,9.365 1.969,0.313 10 false : CAN Main Bus Line (CANH) 3.99,9.073 5.76,9.344 1.771,0.271 10 false : CAN Branch Line (CANH) 3.99,9.458 5.792,9.688 1.802,0.229 10 false : CAN Branch Line (CANL) 0.833,9.438 2.865,9.729 2.031,0.292 10 false : CAN Main Bus Line (CANL) 4.417,5.854 6.49,6.167 2.073,0.313 10 false CAN Junction LH1 Connector 5.563,1.646 7.135,2.01 1.573,0.365 10 false Airbag Sensor Assembly 5.802,1.354 6.375,1.615 0.573,0.26 10 false CANL 5.802,0.771 6.365,1.031 0.563,0.26 10 false CANH 5.823,2.833 6.292,3.063 0.469,0.229 10 false CANL 5.813,2.26 6.333,2.51 0.521,0.25 10 false CANH 5.823,4.906 6.344,5.156 0.521,0.25 10 false CANL 5.823,4.313 6.354,4.563 0.531,0.25 10 false CANH 2.802,8.104 3.24,8.354 0.438,0.25 10 false CANL 4.094,8.104 4.635,8.417 0.542,0.313 10 false CANH 1.073,1.99 1.563,2.24 0.49,0.25 10 false CANL 1.063,1.417 1.573,1.656 0.51,0.24 10 false CANH 1.073,4.365 1.563,4.646 0.49,0.281 10 false CANL 1.063,3.792 1.667,4.094 0.604,0.302 10 false CANH 1.542,1.417 1.792,1.729 0.25,0.313 10 false 9 2.094,1.344 2.333,1.604 0.24,0.26 10 false R 2.083,2.063 2.354,2.313 0.271,0.25 10 false W 1.51,1.99 1.74,2.24 0.229,0.25 10 false 10 1.521,3.792 1.854,4.063 0.333,0.271 10 false 11 2.094,3.688 2.323,3.927 0.229,0.24 10 false V 2.073,4.448 2.333,4.729 0.26,0.281 10 false W 2.052,5.427 2.292,5.646 0.24,0.219 10 false BE 1.531,5.521 1.813,5.792 0.281,0.271 10 false 25 1.542,6.094 1.813,6.375 0.271,0.281 10 false 24 1.083,5.51 1.563,5.781 0.479,0.271 10 false CA1H 1.104,6.094 1.594,6.365 0.49,0.271 10 false CA1L 2.083,6.177 2.323,6.427 0.24,0.25 10 false W 1.521,4.365 1.792,4.635 0.271,0.271 10 false 12 5.563,0.771 5.823,1.021 0.26,0.25 10 false 13 4.49,0.667 4.74,0.906 0.25,0.24 10 false 1 2.917,6.531 3.156,6.76 0.24,0.229 10 false 2 4.26,6.542 4.51,6.781 0.25,0.24 10 false 1 2.906,0.573 3.156,0.802 0.25,0.229 10 false 2 4.25,0.573 4.521,0.823 0.271,0.25 10 false 1 4.49,1.417 4.677,1.583 0.188,0.167 10 false 2 2.688,1.333 2.906,1.542 0.219,0.208 10 false 1 2.698,2.073 2.927,2.375 0.229,0.302 10 false 2 2.688,3.698 2.906,3.917 0.219,0.219 10 false 1 2.688,4.448 2.938,4.698 0.25,0.25 10 false 2 4.49,2.167 4.76,2.427 0.271,0.26 10 false 1 4.49,2.906 4.729,3.146 0.24,0.24 10 false 2 4.49,4.25 4.719,4.51 0.229,0.26 10 false 1 4.49,4.969 4.719,5.177 0.229,0.208 10 false 2 4.99,0.698 5.229,0.927 0.24,0.229 10 false Y 4.979,1.427 5.198,1.667 0.219,0.24 10 false W 4.885,2.188 5.083,2.417 0.198,0.229 10 false L 5.49,2.198 5.719,2.448 0.229,0.25 10 false Y 4.854,2.906 5.104,3.146 0.25,0.24 10 false W 5.427,2.906 5.802,3.167 0.375,0.26 10 false SB 4.135,7.594 4.438,7.854 0.302,0.26 10 false B 3.01,7.594 3.26,7.865 0.25,0.271 10 false W 4.125,6.958 4.375,7.229 0.25,0.271 10 false G 3.01,6.958 3.229,7.198 0.219,0.24 10 false W 5.573,1.354 5.833,1.625 0.26,0.271 10 false 22 5.646,2.271 5.896,2.521 0.25,0.25 10 false 4 5.646,2.833 5.875,3.063 0.229,0.229 10 false 8 4.979,4.958 5.25,5.198 0.271,0.24 10 false W 5,4.229 5.229,4.479 0.229,0.25 10 false P 4.073,7.875 4.302,8.115 0.229,0.24 10 false 13 3.031,7.885 3.281,8.125 0.25,0.24 10 false 26 5.302,1.635 5.677,1.896 0.375,0.26 10 false I47 5.208,5.177 5.594,5.469 0.385,0.292 10 false I13 5,3.135 5.25,3.385 0.25,0.25 10 false j3 0.177,7.823 1.5,8.188 1.323,0.365 10 false x: Suspected Area 3.479,8.708 4.083,9.01 0.604,0.302 10 false 120 Ω 5.188,3.135 7.135,3.51 1.948,0.375 10 false Power Steering ECU Assembly 0.146,4.667 0.448,4.938 0.302,0.271 10 false I77 0.396,4.667 1.958,5.094 1.563,0.427 10 false Air Conditioning Amplifier Assembly 0.271,6.375 0.594,6.625 0.323,0.25 10 false I4 0.469,6.375 1.771,6.75 1.302,0.375 10 false Power Management Control ECU 5.469,5.188 7.104,5.698 1.635,0.51 10 false Main Body ECU (Multiplex Network Body ECU) 2.24,8.333 2.75,8.635 0.51,0.302 10 false ECM 0.396,2.271 3.125,2.688 2.729,0.417 10 false Radio and Display Receiver Assembly*1 0.083,2.271 0.469,2.604 0.385,0.333 10 false I155 5.583,4.323 5.833,4.563 0.25,0.24 10 false 14 5.583,4.917 5.875,5.167 0.292,0.25 10 false 13 2.604,1.521 2.979,1.792 0.375,0.271 10 false I107 2.604,1.885 2.948,2.135 0.344,0.25 10 false I107 2.604,4.26 2.969,4.51 0.365,0.25 10 false I102 2.604,3.885 2.969,4.115 0.365,0.229 10 false I102 3.167,0.583 3.469,0.844 0.302,0.26 10 false I93 3.927,0.583 4.229,0.833 0.302,0.25 10 false I93 4.406,0.865 4.781,1.115 0.375,0.25 10 false I103 4.406,1.25 4.781,1.542 0.375,0.292 10 false I103 4.396,2.729 4.76,2.99 0.365,0.26 10 false I100 4.396,2.354 4.74,2.573 0.344,0.219 10 false I100 4.448,4.438 4.76,4.677 0.313,0.24 10 false I95 3.135,6.531 3.521,6.802 0.385,0.271 10 false I104 2.604,5.625 3.031,5.906 0.427,0.281 10 false I109 2.594,5.99 2.969,6.24 0.375,0.25 10 false I109 4.448,4.792 4.813,5.021 0.365,0.229 10 false I95 3.896,6.531 4.365,6.771 0.469,0.24 10 false I104 1.917,8.333 2.208,8.531 0.292,0.198 10 false A25 0.354,2.698 2.448,3.052 2.094,0.354 10 false Navigation ECU Sub-assembly*2 0.104,2.698 0.479,2.938 0.375,0.24 10 false I67 4.781,7.219 6.719,7.844 1.938,0.625 10 false *2: for Navigation Receiver Type with HDD 4.792,6.76 6.74,7.167 1.948,0.406 10 false *1: for Radio and Display Type 2.688,5.438 2.927,5.656 0.24,0.219 10 false 1 2.677,6.177 2.927,6.396 0.25,0.219 10 false 2 0.104,3.146 0.479,3.385 0.375,0.24 10 false I67 0.344,3.146 2.438,3.5 2.094,0.354 10 false Navigation Receiver Assembly*3 4.771,7.802 6.698,8.531 1.927,0.729 10 false *3: for Navigation Receiver Type without HDD

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the power switch on (IG), turn the blind spot monitor main switch on, turn the cruise control system on using the cruise control main switch (ON/OFF switch), wait at least 60 seconds.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM



HINT:
·

Operating the power switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.

·

Connectors that connect to the CAN junction connector can be distinguished by the color of their CAN bus lines. When the connectors have been disconnected from the CAN junction connector, reconnecting the connectors to non-original positions on the CAN junction connector does not affect system performance. However, it is preferred to reconnect the connectors to their original positions to avoid negative effects on the wiring such as tension on the wire harnesses, and to make future maintenance easier.



PROCEDURE

1.CHECK FOR SHORT TO +B IN CAN BUS LINE (DLC3 BRANCH LINE)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
C252877C06
1.094,2 1.427,2.292 0.333,0.292 1.958,2.271 2.115,2.042 2.115,2.042 2.219,2.042 true 1.958,2.406 2.167,2.615 2.167,2.615 2.292,2.615 true 1.74,2.323 1.531,1.802 1.531,1.802 1.417,1.802 true 1.813,2.438 2.031,2.969 2.031,2.969 2.156,2.969 true 0.135,0.135 0.458,0.49 0.323,0.354 10 false *a 2.281,1.958 2.958,2.198 0.677,0.24 10 false CANH*b 2.365,2.531 3.01,2.76 0.646,0.229 10 false CANL*b 1.177,2.052 1.396,2.219 0.219,0.167 10 false I96 1.25,1.729 1.51,2.01 0.26,0.281 10 false G 2.24,2.865 2.635,3.125 0.396,0.26 10 false W
*a Rear view of wire harness connector
(to CAN Junction RH1 Connector)
*b to DLC3


Disconnect the I96 DLC3 branch line connector from the CAN junction RH1 connector.

NOTICE:
·

Before disconnecting the connector, make a note of where it is connected.

·

Reconnect the connector to its original position.




c.
C210421C89
1.51,0.698 1.948,1 0.438,0.302 2.063,1.875 2.219,1.385 2.219,1.385 2.375,1.385 true 2.063,2.573 2.229,2.979 2.229,2.979 2.396,2.979 true 2.51,2.354 2.938,2.354 true 0.188,0.188 0.49,0.5 0.302,0.313 10 false *1 1.635,0.771 1.948,0.948 0.313,0.177 10 false I39 2.469,1.281 3.083,1.51 0.615,0.229 10 false CANH 2.469,2.896 2.969,3.146 0.5,0.25 10 false CANL 3.01,2.271 3.385,2.479 0.375,0.208 10 false BAT
*1 DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I39-6 (CANH) - I39-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
I39-14 (CANL) - I39-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher



Result:
Result
OK
NG



OK

2.CHECK FOR SHORT TO +B IN CAN BUS LINE

NG

REPAIR OR REPLACE CAN BRANCH LINE CONNECTED TO DLC3

2.CHECK FOR SHORT TO +B IN CAN BUS LINE
a.

Reconnect the I96 DLC3 branch line connector to the CAN junction RH1 connector.


b.
C210421C89
1.51,0.698 1.948,1 0.438,0.302 2.063,1.875 2.219,1.385 2.219,1.385 2.375,1.385 true 2.063,2.573 2.229,2.979 2.229,2.979 2.396,2.979 true 2.51,2.354 2.938,2.354 true 0.188,0.188 0.49,0.5 0.302,0.313 10 false *1 1.635,0.771 1.948,0.948 0.313,0.177 10 false I39 2.469,1.281 3.083,1.51 0.615,0.229 10 false CANH 2.469,2.896 2.969,3.146 0.5,0.25 10 false CANL 3.01,2.271 3.385,2.479 0.375,0.208 10 false BAT
*1 DLC3


Disconnect the connectors from the CAN junction LH1 connector and CAN junction RH1 connector one at a time.

HINT:

Disconnect the ECU and sensor connectors other than the DLC3 branch lines and CAN main bus lines between the CAN junction LH1 connector and CAN junction RH1 connector.



c.

Using an ohmmeter, measure the resistance between terminals 6 (CANH) and 16 (BAT), and between terminals 14 (CANL) and 16 (BAT) of the DLC3 each time a connector is disconnected.

C259933C02
3.406,0.313 3.896,0.604 0.49,0.292 10 false *16 0.49,2.427 0.833,2.719 0.344,0.292 10 false *1 0.208,1.573 0.521,1.771 0.313,0.198 10 false BE 0.74,1.583 1.031,1.854 0.292,0.271 10 false W 1.292,1.667 1.604,1.927 0.313,0.26 10 false *2 1.104,1.01 1.333,1.292 0.229,0.281 10 false P 1.552,1.01 1.792,1.24 0.24,0.229 10 false W 2.188,2.406 2.583,2.677 0.396,0.271 10 false *3 1.969,1.469 2.167,1.708 0.198,0.24 10 false V 2.438,1.469 2.771,1.729 0.333,0.26 10 false W 3.125,1.656 3.448,1.948 0.323,0.292 10 false *4 2.896,1.063 3.198,1.292 0.302,0.229 10 false Y 3.365,1.063 3.615,1.354 0.25,0.292 10 false W 4.063,2.406 4.406,2.698 0.344,0.292 10 false *5 3.833,1.604 4.063,1.854 0.229,0.25 10 false L 4.333,1.604 4.604,1.865 0.271,0.26 10 false W 3.823,2.01 4.042,2.26 0.219,0.25 10 false Y 4.323,2.01 4.667,2.302 0.344,0.292 10 false SB 4.969,1.635 5.281,1.833 0.313,0.198 10 false *6 4.719,0.875 4.927,1.104 0.208,0.229 10 false G 5.25,0.875 5.5,1.115 0.25,0.24 10 false W 4.729,1.24 4.979,1.479 0.25,0.24 10 false B 5.25,1.25 5.531,1.5 0.281,0.25 10 false W 5.688,1.479 5.896,1.708 0.208,0.229 10 false R 6.156,1.469 6.469,1.75 0.313,0.281 10 false W 5.792,2.25 6.469,2.469 0.677,0.219 10 false *7 (*A) 5.802,2.406 6.448,2.688 0.646,0.281 10 false *8 (*B) 6.365,1.958 6.583,2.24 0.219,0.281 10 false B 6.854,1.958 7.125,2.281 0.271,0.323 10 false W 0.073,3.521 0.302,3.76 0.229,0.24 10 false B 0.552,3.521 0.802,3.729 0.25,0.208 10 false W 1.198,3.917 1.542,4.167 0.344,0.25 10 false *9 1,4.771 1.302,5.052 0.302,0.281 10 false R 1.479,4.771 1.75,5.01 0.271,0.24 10 false W 2.125,4.823 2.51,5.188 0.385,0.365 10 false *10 1.958,5.406 2.229,5.656 0.271,0.25 10 false G 2.427,5.406 2.677,5.646 0.25,0.24 10 false W 3.167,3.906 3.531,4.177 0.365,0.271 10 false *11 3.01,4.76 3.24,5 0.229,0.24 10 false L 3.479,4.75 3.74,4.969 0.26,0.219 10 false W 4.208,4.813 4.604,5.104 0.396,0.292 10 false *12 3.958,5.271 4.323,5.531 0.365,0.26 10 false GR 4.542,5.271 4.75,5.5 0.208,0.229 10 false W 4.031,5.667 4.26,5.906 0.229,0.24 10 false Y 4.542,5.667 4.792,5.917 0.25,0.25 10 false W 5.229,3.927 5.583,4.229 0.354,0.302 10 false *13 5.042,4.823 5.229,5.073 0.188,0.25 10 false V 5.531,4.823 5.813,5.042 0.281,0.219 10 false W 6.104,4.813 6.729,5.104 0.625,0.292 10 false *14 (*C) 6.031,5.25 6.281,5.479 0.25,0.229 10 false B 6.542,5.25 6.792,5.49 0.25,0.24 10 false W 5.969,5.688 6.302,5.979 0.333,0.292 10 false BE 6.552,5.698 6.844,5.969 0.292,0.271 10 false W 3.427,6.167 3.813,6.479 0.385,0.313 10 false *15 5.74,2.563 6.385,2.844 0.646,0.281 10 false *17 (*D)
*A for Navigation Receiver Type with HDD *B for Radio and Display Type
*C w/ Automatic High Beam System *D for Navigation Receiver Type without HDD
*1 Power Management Control ECU *2 Main Body ECU (Multiplex Network Body ECU)
*3 Air Conditioning Amplifier Assembly *4 Airbag Sensor Assembly
*5 Power Steering ECU Assembly *6 ECM
*7 Navigation ECU Sub-assembly *8 Radio and Display Receiver Assembly
*9 Combination Meter Assembly *10 DLC3
*11 Smart Key ECU Assembly (Certification ECU) *12 Brake Booster with Master Cylinder Assembly (Skid Control ECU)
*13 Steering Sensor *14 Headlight Swivel ECU Assembly (AFS ECU)
*15 CAN Junction RH1 Connector *16 CAN Junction LH1 Connector
*17 Navigation Receiver Assembly - -


C241464C08
2.396,0.427 2.74,0.698 0.344,0.271 10 false *a 3.615,3.958 3.844,4.198 0.229,0.24 10 false I95 3.573,3.688 3.875,3.927 0.302,0.24 10 false I102 3.573,3.427 3.875,3.667 0.302,0.24 10 false I103 3.573,3.156 3.875,3.396 0.302,0.24 10 false I100 3.573,4.25 3.875,4.49 0.302,0.24 10 false I109 3.573,2.865 3.875,3.104 0.302,0.24 10 false I104 3.573,2.594 3.875,2.833 0.302,0.24 10 false I107 3.615,2.313 3.844,2.552 0.229,0.24 10 false I93
*a Component without harness connected
(CAN Junction LH1 Connector)
- -


Wiring Color:
CAN Junction LH1 Connector Side Code Color (CANH Side) Color (CANL Side)
CAN main bus line (bus line connecting CAN junction LH1 connector and CAN junction RH1 connector) I93 B W
·

Navigation ECU sub-assembly*1

·

Radio and display receiver assembly*2

·

Navigation receiver assembly*3


I107 R W
ECM I104 G W
Power steering ECU assembly I100 L W
Airbag sensor assembly I103 Y W
Air conditioning amplifier assembly I102 V W
Main body ECU (Multiplex network body ECU) I95 P W
Power management control ECU I109 BE W


·

*1: for Navigation Receiver Type with HDD

·

*2: for Radio and Display Type

·

*3: for Navigation Receiver Type without HDD


C253115C04
3.333,2.573 3.625,2.74 0.292,0.167 10 false I112 3.354,3.677 3.646,3.844 0.292,0.167 10 false I96 3.333,3.115 3.625,3.281 0.292,0.167 10 false I110 3.354,2.854 3.646,3.021 0.292,0.167 10 false I97 3.333,4.25 3.625,4.417 0.292,0.167 10 false I101 3.354,3.958 3.646,4.125 0.292,0.167 10 false I94 3.333,3.417 3.625,3.583 0.292,0.167 10 false I106 2.469,0.479 2.729,0.771 0.26,0.292 10 false *a
*a Component without harness connected
(CAN Junction RH1 Connector)
- -


Wiring Color:
CAN Junction RH1 Connector Side Code Color (CANH Side) Color (CANL Side)
Head light swivel ECU assembly (AFS ECU)* I112 BE W
Steering sensor I97 V W
Brake booster with master cylinder assembly (Skid control ECU) I110 Y W
Smart key ECU assembly (Certification ECU) I106 L W
DLC3 I96 G W
Combination meter assembly I94 R W
CAN main bus line (bus line connecting CAN junction LH1 connector and CAN junction RH1 connector) I101 B W


*: w/ Automatic High Beam System


NOTICE:

Do not reconnect the disconnected connectors until this inspection is complete because there may be a short to +B in 2 or more CAN bus lines.



Result:
Symptom Proceed to
The resistance between terminals 6 (CANH) and 16 (BAT), or the resistance between 14 (CANL) and 16 (BAT) is still below 6 kΩ when all the specified connectors are disconnected from the CAN junction connector. (There is a short to +B in the CAN main bus lines between the CAN junction LH1 connector and CAN junction RH1 connector.) A
The resistance between terminals 6 (CANH) and 16 (BAT), or the resistance between 14 (CANL) and 16 (BAT) becomes normal (6 kΩ or higher) when a connector is disconnected from the CAN junction connector. (There is a short to +B in one of the areas that relate to one or more of the disconnected bus lines.) B


d.

When there is a short to +B in one or more of the bus lines that connect to an ECU or sensor:

i.

Reconnect all of the connectors to the CAN junction connector, except for the one that was disconnected last (the bus line that is shorted to +B). Check that the resistance shown on the tester is normal (6 kΩ or higher) to confirm that there is a short to +B in the one bus line only.

HINT:
·

Connectors that connect to the CAN junction connector can be distinguished by the color of their CAN bus lines.

·

Reconnecting the connectors to non-original positions on the CAN junction connector does not affect system performance. However, it is preferred to reconnect the connectors to their original positions to avoid negative effects on the wiring such as tension on the wire harnesses, and to make future maintenance easier.





e.

When there is no short to +B in any of the bus lines that connect to the ECUs and sensors:

i.

With all the specified connectors for ECUs and sensors disconnected, proceed with the inspection of the CAN bus main lines between the CAN junction LH1 connector and CAN junction RH1 connector.




A

3.CHECK FOR SHORT TO +B IN CAN BUS LINE (CAN JUNCTION RH1 CONNECTOR)

B

5.CHECK FOR SHORT TO +B IN CAN BUS LINE (ECU, SENSOR)
3.CHECK FOR SHORT TO +B IN CAN BUS LINE (CAN JUNCTION RH1 CONNECTOR)
a.
C248239C07
2.719,1.438 3.104,1.698 0.385,0.26 2.865,2.146 2.594,1.74 2.594,1.74 2.094,1.74 true 2.865,2.354 2.865,2.698 2.865,2.698 2.188,2.698 true 2.74,2.229 2.479,1.896 2.479,1.896 2.333,1.896 true 2.813,2.323 2.573,2.156 2.573,2.156 2.438,2.156 true 0.167,0.156 0.5,0.5 0.333,0.344 10 false *a 1.531,1.656 2.208,1.917 0.677,0.26 10 false CANH*b 1.635,2.594 2.281,2.813 0.646,0.219 10 false CANL*b 2.156,1.833 2.396,2.083 0.24,0.25 10 false B 2.25,2.083 2.542,2.333 0.292,0.25 10 false W 2.792,1.49 3.135,1.729 0.344,0.24 10 false I101
*a Rear view of wire harness connector
(to CAN Junction RH1 Connector)
*b to CAN Junction LH1 Connector


Disconnect the I101 CAN main bus line connector from the CAN junction RH1 connector.

NOTICE:
·

Before disconnecting the connector, make a note of where it is connected.

·

Reconnect the connector to its original position.




b.
C210421C89
1.51,0.698 1.948,1 0.438,0.302 2.063,1.875 2.219,1.385 2.219,1.385 2.375,1.385 true 2.063,2.573 2.229,2.979 2.229,2.979 2.396,2.979 true 2.51,2.354 2.938,2.354 true 0.188,0.188 0.49,0.5 0.302,0.313 10 false *1 1.635,0.771 1.948,0.948 0.313,0.177 10 false I39 2.469,1.281 3.083,1.51 0.615,0.229 10 false CANH 2.469,2.896 2.969,3.146 0.5,0.25 10 false CANL 3.01,2.271 3.385,2.479 0.375,0.208 10 false BAT
*1 DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I39-6 (CANH) - I39-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
I39-14 (CANL) - I39-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher



Result:
Result
OK
NG



OK

4.CHECK FOR SHORT TO +B IN CAN BUS LINE (CAN JUNCTION LH1 CONNECTOR - CAN JUNCTION RH1 CONNECTOR)

NG

REPLACE CAN JUNCTION RH1 CONNECTOR

4.CHECK FOR SHORT TO +B IN CAN BUS LINE (CAN JUNCTION LH1 CONNECTOR - CAN JUNCTION RH1 CONNECTOR)
a.

Reconnect the I101 CAN main bus line connector to the CAN junction RH1 connector.


b.
C248247C05
2.573,1.406 2.906,1.646 0.333,0.24 2.646,2.052 2.292,1.854 2.292,1.854 2,1.854 true 2.594,2.25 2.594,2.552 2.594,2.552 1.948,2.552 true 2.51,2.146 2.354,2.052 2.354,2.052 2.24,2.052 true 3.052,2.531 3.052,2.229 3.052,2.229 2.729,2.229 true 0.125,0.167 0.406,0.448 0.281,0.281 10 false *a 1.438,1.76 2.177,2.073 0.74,0.313 10 false CANH*b 2.76,2.573 3.354,2.792 0.594,0.219 10 false CANL*b 2.656,1.448 2.979,1.688 0.323,0.24 10 false I93 2.094,1.948 2.333,2.167 0.24,0.219 10 false B 1.771,2.469 2.021,2.698 0.25,0.229 10 false W
*a Rear view of wire harness connector
(to CAN Junction LH1 Connector)
*b to CAN Junction RH1 Connector


Disconnect the I93 CAN main bus line connector from the CAN junction LH1 connector.

NOTICE:
·

Before disconnecting the connector, make a note of where it is connected.

·

Reconnect the connector to its original position.




c.
C210421C89
1.51,0.698 1.948,1 0.438,0.302 2.063,1.875 2.219,1.385 2.219,1.385 2.375,1.385 true 2.063,2.573 2.229,2.979 2.229,2.979 2.396,2.979 true 2.51,2.354 2.938,2.354 true 0.188,0.188 0.49,0.5 0.302,0.313 10 false *1 1.635,0.771 1.948,0.948 0.313,0.177 10 false I39 2.469,1.281 3.083,1.51 0.615,0.229 10 false CANH 2.469,2.896 2.969,3.146 0.5,0.25 10 false CANL 3.01,2.271 3.385,2.479 0.375,0.208 10 false BAT
*1 DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I39-6 (CANH) - I39-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
I39-14 (CANL) - I39-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher



Result:
Result
OK
NG



OK

REPLACE CAN JUNCTION LH1 CONNECTOR

NG

REPAIR OR REPLACE CAN MAIN BUS LINE (CAN JUNCTION LH1 CONNECTOR - CAN JUNCTION RH1 CONNECTOR)

5.CHECK FOR SHORT TO +B IN CAN BUS LINE (ECU, SENSOR)
a.

Reconnect the connector of the bus line that is shorted to +B to the CAN junction connector (the connector that caused the bus line resistance to change to 6 kΩ or higher when it was disconnected).


b.
C210421C89
1.51,0.698 1.948,1 0.438,0.302 2.063,1.875 2.219,1.385 2.219,1.385 2.375,1.385 true 2.063,2.573 2.229,2.979 2.229,2.979 2.396,2.979 true 2.51,2.354 2.938,2.354 true 0.188,0.188 0.49,0.5 0.302,0.313 10 false *1 1.635,0.771 1.948,0.948 0.313,0.177 10 false I39 2.469,1.281 3.083,1.51 0.615,0.229 10 false CANH 2.469,2.896 2.969,3.146 0.5,0.25 10 false CANL 3.01,2.271 3.385,2.479 0.375,0.208 10 false BAT
*1 DLC3


Disconnect the connector that includes the DLC3 connected CAN lines (such as CANH and CANL) from the ECU or sensor to which the bus line shorted to +B is connected.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>TERMINALS OF ECU


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I39-6 (CANH) - I39-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
I39-14 (CANL) - I39-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher


HINT:

If the resistance changes to 6 kΩ or higher when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.



Result:
Result
OK
NG



OK

REPLACE CORRESPONDING ECU OR SENSOR

NG

REPAIR OR REPLACE CORRESPONDING ECU OR SENSOR BUS LINE OR CONNECTOR