Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › 2014.05–2015.04
RM2040EQ _57 Power Source / Network _014721 NETWORKING _0075042 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Navigation ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Navigation ECU Communication Stop Mode Either condition is met:
·

"Display and Navigation (AVN1)" is not displayed on the CAN Bus Check screen of the GTS

Click here(Click here)

·

Communication system DTCs (DTCs that start with U) that correspond to "Navigation ECU Communication Stop Mode" in "DTC Combination Table" are output

Click here(Click here)


·

Navigation ECU sub-assembly branch line or connector*1

·

Navigation receiver assembly branch line or connector*2

·

Power source circuit of navigation ECU sub-assembly*1

·

Power source circuit of navigation receiver assembly*2

·

Navigation ECU sub-assembly ground circuit*1

·

Navigation receiver assembly ground circuit*2

·

Navigation ECU sub-assembly*1

·

Navigation receiver assembly*2



·

*1: for Navigation Receiver Type with HDD

·

*2: for Navigation Receiver Type without HDD


WIRING DIAGRAM

C252910E25
4.313,0.438 4.063,0.438 4.063,0.438 3.604,1.146 false 2.156,0.802 2.292,0.802 2.292,0.802 2.479,1.146 false 2.708,0.427 3.188,0.719 0.479,0.292 10 false DLC3 5.719,3.49 6.604,3.833 0.885,0.344 10 false Trouble Area 0.323,2.667 1.51,3.198 1.188,0.531 10 false Combination Meter Assembly 4.427,0.344 6.563,0.604 2.135,0.26 10 false CAN Junction LH1 Connector 6.167,2.104 6.667,2.365 0.5,0.26 10 false 120 Ω 0.677,2.125 1.292,2.406 0.615,0.281 10 false 120 Ω 1.479,5.115 3.396,5.448 1.917,0.333 10 false : CAN Main Bus Line (CANH) 1.469,5.406 3.385,5.74 1.917,0.333 10 false : CAN Main Bus Line (CANL) 4.438,5.115 6.198,5.448 1.76,0.333 10 false : CAN Branch Line (CANH) 4.438,5.406 6.125,5.74 1.688,0.333 10 false : CAN Branch Line (CANL) 3.833,3.135 4.313,3.313 0.479,0.177 10 false CANH 4.313,3.135 4.771,3.313 0.458,0.177 10 false CANL 3.531,3.5 3.771,3.729 0.24,0.229 10 false IG 3.542,4.167 4.125,4.396 0.583,0.229 10 false ACC1 4.521,3.479 4.99,3.771 0.469,0.292 10 false GND1 3.865,2.708 4.083,2.938 0.219,0.229 10 false 9 4.438,2.708 4.677,2.938 0.24,0.229 10 false 10 5.052,3.26 5.281,3.479 0.229,0.219 10 false 7 2.365,3.719 3.448,3.906 1.083,0.188 10 false ECU-IG1 NO. 2 2.365,3.292 3.063,3.552 0.698,0.26 10 false RADIO-B 2.375,4.344 3.094,4.604 0.719,0.26 10 false ECU-ACC 0.271,0.677 2.323,0.958 2.052,0.281 10 false CAN Junction RH1 Connector 3.25,4.5 5.406,4.813 2.156,0.313 10 false Navigation ECU Sub-assembly 3.219,3.51 3.656,3.792 0.438,0.281 10 false I67 6.167,2.677 6.583,2.917 0.417,0.24 10 false ECM 3.917,2.927 4.271,3.094 0.354,0.167 10 false I67 4.313,2.927 4.667,3.094 0.354,0.167 10 false I67 3.219,4.177 3.573,4.344 0.354,0.167 10 false I64 5.01,3.469 5.406,3.708 0.396,0.24 10 false I64 3.26,3.323 3.417,3.531 0.156,0.208 10 false 1 3.271,3.979 3.49,4.198 0.219,0.219 10 false 3 0.063,0.031 3.75,0.385 3.688,0.354 12 false V Bus (for Navigation Receiver Type with HDD): 3.51,3.146 3.885,3.458 0.375,0.313 10 false +B1 3.219,3.135 3.583,3.385 0.365,0.25 10 false I64 3.26,2.948 3.427,3.188 0.167,0.24 10 false 4

C252910E26
4.313,0.438 4.063,0.438 4.063,0.438 3.604,1.146 false 2.156,0.802 2.292,0.802 2.292,0.802 2.479,1.146 false 2.708,0.427 3.188,0.719 0.479,0.292 10 false DLC3 5.719,3.49 6.604,3.833 0.885,0.344 10 false Trouble Area 0.323,2.667 1.51,3.198 1.188,0.531 10 false Combination Meter Assembly 4.427,0.344 6.563,0.604 2.135,0.26 10 false CAN Junction LH1 Connector 6.167,2.104 6.667,2.365 0.5,0.26 10 false 120 Ω 0.677,2.125 1.292,2.406 0.615,0.281 10 false 120 Ω 1.479,5.115 3.396,5.448 1.917,0.333 10 false : CAN Main Bus Line (CANH) 1.469,5.406 3.385,5.74 1.917,0.333 10 false : CAN Main Bus Line (CANL) 4.438,5.115 6.198,5.448 1.76,0.333 10 false : CAN Branch Line (CANH) 4.438,5.406 6.125,5.74 1.688,0.333 10 false : CAN Branch Line (CANL) 3.833,3.135 4.313,3.313 0.479,0.177 10 false CANH 4.313,3.135 4.771,3.313 0.458,0.177 10 false CANL 3.531,3.5 3.771,3.729 0.24,0.229 10 false IG 3.542,4.167 4.125,4.396 0.583,0.229 10 false ACC1 4.521,3.479 4.99,3.771 0.469,0.292 10 false GND1 3.865,2.708 4.083,2.938 0.219,0.229 10 false 9 4.438,2.708 4.677,2.938 0.24,0.229 10 false 10 5.052,3.26 5.281,3.479 0.229,0.219 10 false 7 2.365,3.719 3.448,3.906 1.083,0.188 10 false ECU-IG1 NO. 2 2.365,3.292 3.063,3.552 0.698,0.26 10 false RADIO-B 2.375,4.344 3.094,4.604 0.719,0.26 10 false ECU-ACC 0.271,0.677 2.323,0.958 2.052,0.281 10 false CAN Junction RH1 Connector 3.26,4.469 5.417,4.781 2.156,0.313 10 false Navigation Receiver Assembly 3.219,3.51 3.656,3.792 0.438,0.281 10 false I67 6.167,2.677 6.583,2.917 0.417,0.24 10 false ECM 3.917,2.927 4.271,3.094 0.354,0.167 10 false I67 4.313,2.927 4.667,3.094 0.354,0.167 10 false I67 3.219,4.177 3.573,4.344 0.354,0.167 10 false I64 5.01,3.469 5.406,3.708 0.396,0.24 10 false I64 3.26,3.323 3.417,3.531 0.156,0.208 10 false 1 3.271,3.979 3.49,4.198 0.219,0.219 10 false 3 0.063,0.031 3.854,0.385 3.792,0.354 12 false V Bus (for Navigation Receiver Type without HDD): 3.51,3.146 3.885,3.458 0.375,0.313 10 false +B1 3.219,3.135 3.583,3.385 0.365,0.25 10 false I64 3.26,2.948 3.427,3.188 0.167,0.24 10 false 4

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the power switch on (IG), turn the blind spot monitor main switch on, wait at least 60 seconds.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Operating the power switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK VEHICLE TYPE
a.

Check vehicle type.

Result:
Result Proceed to
for Navigation Receiver Type with HDD A
for Navigation Receiver Type without HDD B




A

2.CHECK FOR OPEN IN CAN BUS LINES (NAVIGATION ECU SUB-ASSEMBLY BRANCH LINE)

B

4.CHECK FOR OPEN IN CAN BUS LINES (NAVIGATION RECEIVER ASSEMBLY BRANCH LINE)
2.CHECK FOR OPEN IN CAN BUS LINES (NAVIGATION ECU SUB-ASSEMBLY BRANCH LINE)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
C240580C15
0.344,1.083 0.802,1.365 0.458,0.281 1.531,0.563 1.781,0.563 1.781,0.563 1.781,1.885 true 2.115,0.552 1.896,0.552 1.896,0.552 1.896,1.885 true 0.135,0.135 0.344,0.323 0.208,0.188 10 false *a 2.188,0.479 2.635,0.677 0.448,0.198 10 false CANL 1.083,0.49 1.531,0.688 0.448,0.198 10 false CANH 0.469,1.135 0.792,1.302 0.323,0.167 10 false I67
*a Front view of wire harness connector
(to Navigation ECU Sub-assembly)


Disconnect the I67 navigation ECU sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I67-9 (CANH) - I67-10 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω



Result:
Result
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (NAVIGATION ECU SUB-ASSEMBLY)

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
C241290C14
0.125,1.615 0.615,1.927 0.49,0.313 0.208,3.49 0.698,3.802 0.49,0.313 1.448,3.844 1.448,4.177 1.448,4.177 1.302,4.177 true 1.792,3.5 1.792,2.708 1.792,2.708 2.01,2.708 true 2.021,3.563 2.427,3.563 true 0.667,1.083 0.802,1.083 0.802,1.083 0.802,1.646 true 0.167,0.073 0.344,0.26 0.177,0.188 10 false *a 0.458,1 0.708,1.219 0.25,0.219 10 false IG 2.104,2.625 2.667,2.927 0.563,0.302 10 false ACC1 0.854,4.094 1.438,4.354 0.583,0.26 10 false GND1 0.281,1.677 0.583,1.854 0.302,0.177 10 false I67 0.365,3.552 0.667,3.729 0.302,0.177 10 false I64 2.5,3.469 2.885,3.75 0.385,0.281 10 false +B1
*a Front view of wire harness connector
(to Navigation ECU Sub-assembly)


Disconnect the I64 navigation ECU sub-assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I64-7 (GND1) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω



c.

Reconnect the cable to the negative (-) auxiliary battery terminal.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
I64-3 (ACC1) - Body ground Power switch on (ACC) 11 to 14 V
I64-4 (+B1) - Body ground Power switch off 11 to 14 V
I67-1 (IG) - Body ground Power switch on (IG) 11 to 14 V



Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

4.CHECK FOR OPEN IN CAN BUS LINES (NAVIGATION RECEIVER ASSEMBLY BRANCH LINE)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
C240580C15
0.344,1.083 0.802,1.365 0.458,0.281 1.531,0.563 1.781,0.563 1.781,0.563 1.781,1.885 true 2.115,0.552 1.896,0.552 1.896,0.552 1.896,1.885 true 0.135,0.135 0.344,0.323 0.208,0.188 10 false *a 2.188,0.479 2.635,0.677 0.448,0.198 10 false CANL 1.083,0.49 1.531,0.688 0.448,0.198 10 false CANH 0.469,1.135 0.792,1.302 0.323,0.167 10 false I67
*a Front view of wire harness connector
(to Navigation Receiver Assembly)


Disconnect the I67 navigation receiver assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I67-9 (CANH) - I67-10 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω



Result:
Result
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (NAVIGATION RECEIVER ASSEMBLY)

5.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
C241290C14
0.125,1.615 0.615,1.927 0.49,0.313 0.208,3.49 0.698,3.802 0.49,0.313 1.448,3.844 1.448,4.177 1.448,4.177 1.302,4.177 true 1.792,3.5 1.792,2.708 1.792,2.708 2.01,2.708 true 2.021,3.563 2.427,3.563 true 0.667,1.083 0.802,1.083 0.802,1.083 0.802,1.646 true 0.167,0.073 0.344,0.26 0.177,0.188 10 false *a 0.458,1 0.708,1.219 0.25,0.219 10 false IG 2.104,2.625 2.667,2.927 0.563,0.302 10 false ACC1 0.854,4.094 1.438,4.354 0.583,0.26 10 false GND1 0.281,1.677 0.583,1.854 0.302,0.177 10 false I67 0.365,3.552 0.667,3.729 0.302,0.177 10 false I64 2.5,3.469 2.885,3.75 0.385,0.281 10 false +B1
*a Front view of wire harness connector
(to Navigation Receiver Assembly)


Disconnect the I64 navigation receiver assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I64-7 (GND1) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω



c.

Reconnect the cable to the negative (-) auxiliary battery terminal.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
I64-3 (ACC1) - Body ground Power switch on (ACC) 11 to 14 V
I64-4 (+B1) - Body ground Power switch off 11 to 14 V
I67-1 (IG) - Body ground Power switch on (IG) 11 to 14 V



Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)