Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › 2014.05–2015.04
RM2040EQ _57 Power Source / Network _014721 NETWORKING _0075042 CAN COMMUNICATION SYSTEM C

NETWORKING  CAN COMMUNICATION SYSTEM  U1002  Lost Communication with Gateway Module  


DESCRIPTION

·

The power management control ECU will store this DTC when no signals can be received from the ECUs that have been memorized as those that are connected to sub bus 11.

·

When the power management control ECU receives a response signal from the ECUs connected to sub bus 11, the power management control ECU recognizes and memorizes that the ECU is connected to sub bus 11. Based on this memorized data, the power management control ECU monitors for malfunctions in the ECUs connected to sub bus 11 when communicating with those ECUs. If the power management control ECU cannot receive response signals from the ECUs that have been memorized as those connected to sub bus 11, the power management control ECU determines that a malfunction exists.


DTC No. Detection Item DTC Detection Condition Trouble Area Note
U1002 Lost Communication with Gateway Module The power management control ECU cannot receive signals from all ECUs that have been memorized as those connected to sub bus 11.
·

Open or short in sub bus 11 main lines or connector

·

Short in sub bus 11 branch lines or connector

·

Power management control ECU

·

Blind spot monitor sensor LH

(w/ Blind Spot Monitor System)

·

Blind spot monitor sensor RH

(w/ Blind Spot Monitor System)

·

Rear television camera assembly

(w/ Parking Assist Monitor System without Parallel Parking Assist Function)

·

Open or short in CAN No. 2 junction connector

·

Open or short in CAN No. 3 junction connector

·

Open or short in CAN No. 4 junction connector


The power management control ECU stores DTCs when it detects a communication stop or network communication error for ECUs connected to sub bus 11.

HINT:

This diagnostic procedure is for when DTC U1002 is output by the power management control ECU (GTS display: PM1 Gateway).


WIRING DIAGRAM

Sub Bus 11: w/o Parking Assist Monitor System without Parallel Parking Assist Function
C250836E04
5.302,0.521 6.51,0.708 1.208,0.188 10 false x: Suspected Area 1.26,0.51 2.552,0.917 1.292,0.406 10 false Power Management Control ECU 3.458,0.281 3.875,0.469 0.417,0.188 10 false 120 Ω 5.771,3.302 6.99,3.677 1.219,0.375 10 false Blind Spot Monitor Sensor RH 3.406,7.385 3.823,7.573 0.417,0.188 10 false 120 Ω 4.719,5.323 6.688,5.51 1.969,0.188 10 false CAN No. 3 Junction Connector 4.958,7.031 6.906,7.219 1.948,0.188 10 false CAN No. 4 Junction Connector 0.844,2.76 2.833,2.948 1.99,0.188 10 false CAN No. 2 Junction Connector 3.646,7.969 5.365,8.156 1.719,0.188 10 false : CAN Branch Line (CANH) 3.646,8.375 5.365,8.563 1.719,0.188 10 false : CAN Branch Line (CANL) 0.979,7.969 2.896,8.156 1.917,0.188 10 false : CAN Main Bus Line (CANH) 0.979,8.375 2.896,8.563 1.917,0.188 10 false : CAN Main Bus Line (CANL) 2.74,0.917 3.125,1.083 0.385,0.167 10 false CA2L 1.031,4.979 1.417,5.146 0.385,0.167 10 false CA1P 1.031,5.563 1.417,5.729 0.385,0.167 10 false CA1N 5.458,3.302 5.854,3.469 0.396,0.167 10 false O28 0.458,5.833 1.635,6.188 1.177,0.354 10 false Blind Spot Monitor Sensor LH 0.156,5.833 0.49,6 0.333,0.167 10 false T10 2.99,1.125 3.198,1.292 0.208,0.167 10 false 35 1.469,4.99 1.677,5.156 0.208,0.167 10 false 8 1.469,5.563 1.677,5.729 0.208,0.167 10 false 4 2.99,2.083 3.198,2.25 0.208,0.167 10 false 22 4,2.083 4.208,2.25 0.208,0.167 10 false 11 4.344,2.469 4.552,2.635 0.208,0.167 10 false 9 4.344,3.01 4.552,3.177 0.208,0.167 10 false 20 2.677,4.99 2.885,5.156 0.208,0.167 10 false 10 1.854,4.927 2.063,5.094 0.208,0.167 10 false R 1.865,5.656 2.073,5.823 0.208,0.167 10 false B 2.677,5.563 2.885,5.729 0.208,0.167 10 false 21 2.896,1.365 3.104,1.531 0.208,0.167 10 false LG 4.979,2.385 5.188,2.552 0.208,0.167 10 false R 5,3.104 5.208,3.271 0.208,0.167 10 false B 4.063,1.365 4.271,1.531 0.208,0.167 10 false G 2.99,1.844 3.104,2.01 0.115,0.167 10 false B 4.063,1.844 4.229,2.01 0.167,0.167 10 false V 4.01,1.125 4.219,1.292 0.208,0.167 10 false 34 5.583,2.458 5.792,2.625 0.208,0.167 10 false 8 5.563,3.031 5.771,3.198 0.208,0.167 10 false 4 1.073,0.51 1.219,0.677 0.146,0.167 10 false I3 4.021,0.917 4.406,1.083 0.385,0.167 10 false CA2H 5.74,2.458 6.177,2.625 0.438,0.167 10 false CA1P 5.729,3.042 6.167,3.208 0.438,0.167 10 false CA1N 4.031,6.531 4.24,6.698 0.208,0.167 10 false 3 3.021,6.531 3.229,6.698 0.208,0.167 10 false 2 3.01,6.323 3.219,6.49 0.208,0.167 10 false B 4.042,6.323 4.25,6.49 0.208,0.167 10 false L 2.99,5.979 3.198,6.146 0.208,0.167 10 false 20 4.01,5.979 4.219,6.146 0.208,0.167 10 false 9 2.99,4.531 3.198,4.698 0.208,0.167 10 false 22 4.01,4.531 4.229,4.698 0.219,0.167 10 false 11 4.01,3.531 4.219,3.698 0.208,0.167 10 false 10 2.979,3.531 3.188,3.698 0.208,0.167 10 false 21 3,4.042 3.208,4.208 0.208,0.167 10 false B 4.042,4.042 4.25,4.208 0.208,0.167 10 false G 2.729,6.729 3.167,6.896 0.438,0.167 10 false CANL 4.031,6.74 4.469,6.906 0.438,0.167 10 false CANH 0.521,2.76 0.833,2.927 0.313,0.167 10 false O30 4.406,5.323 4.708,5.49 0.302,0.167 10 false T15 4.646,7.031 4.927,7.198 0.281,0.167 10 false T16

Sub Bus 11: w/ Parking Assist Monitor System without Parallel Parking Assist Function
C324698E01
3.354,0.354 3.823,0.604 0.469,0.25 10 false 120 Ω 3.396,7.396 3.865,7.646 0.469,0.25 10 false 120 Ω 5.25,0.292 6.5,0.563 1.25,0.271 10 false x: Suspected Area 1.146,0.531 1.375,0.823 0.229,0.292 10 false I3 1.323,0.531 2.563,1.073 1.24,0.542 10 false Power Management Control ECU 2.74,0.917 3.146,1.198 0.406,0.281 10 false CA2L 4.052,0.917 4.458,1.198 0.406,0.281 10 false CA2H 2.969,1.146 3.198,1.438 0.229,0.292 10 false 35 4.01,1.135 4.24,1.427 0.229,0.292 10 false 34 2.885,1.354 3.115,1.646 0.229,0.292 10 false LG 4.063,1.344 4.292,1.635 0.229,0.292 10 false G 2.958,1.885 3.188,2.177 0.229,0.292 10 false B 4.073,1.896 4.302,2.188 0.229,0.292 10 false V 2.979,2.094 3.208,2.385 0.229,0.292 10 false 22 4,2.083 4.229,2.375 0.229,0.292 10 false 11 4.302,2.469 4.531,2.76 0.229,0.292 10 false 9 4.302,3.063 4.531,3.354 0.229,0.292 10 false 20 4.99,2.417 5.219,2.708 0.229,0.292 10 false R 4.99,3.135 5.219,3.427 0.229,0.292 10 false B 5.583,2.479 5.813,2.771 0.229,0.292 10 false 8 5.583,3.052 5.813,3.344 0.229,0.292 10 false 4 5.74,2.479 6.146,2.76 0.406,0.281 10 false CA1P 5.729,3.042 6.135,3.323 0.406,0.281 10 false CA1N 5.458,3.313 5.865,3.594 0.406,0.281 10 false O28 5.75,3.313 6.917,4 1.167,0.688 10 false Blind Spot Monitor Sensor RH* 0.615,2.531 0.948,2.823 0.333,0.292 10 false O30 0.917,2.531 2.885,2.833 1.969,0.302 10 false CAN No. 2 Junction Connector 4,3.563 4.229,3.854 0.229,0.292 10 false 10 2.979,3.563 3.208,3.854 0.229,0.292 10 false 21 4.063,3.813 4.292,4.104 0.229,0.292 10 false G 2.99,3.802 3.219,4.094 0.229,0.292 10 false B 4.01,4.094 4.24,4.385 0.229,0.292 10 false 4 2.979,4.104 3.208,4.396 0.229,0.292 10 false 15 2.74,4.24 2.969,4.531 0.229,0.292 10 false 3 2.677,4.823 2.906,5.115 0.229,0.292 10 false 14 4.323,5.021 4.552,5.313 0.229,0.292 10 false 1 4.313,5.625 4.542,5.917 0.229,0.292 10 false 12 2.99,5.979 3.219,6.271 0.229,0.292 10 false 13 4.031,5.979 4.26,6.271 0.229,0.292 10 false 2 2.042,4.177 2.271,4.469 0.229,0.292 10 false R 2.052,4.927 2.281,5.219 0.229,0.292 10 false B 1.49,4.823 1.719,5.115 0.229,0.292 10 false 4 1.49,4.24 1.719,4.531 0.229,0.292 10 false 8 1.031,4.24 1.438,4.521 0.406,0.281 10 false CA1P 1.01,4.813 1.417,5.094 0.406,0.281 10 false CA1N 0.115,5.104 0.448,5.396 0.333,0.292 10 false T10 0.385,5.104 1.531,5.667 1.146,0.563 10 false Blind Spot Monitor Sensor LH* 4.417,4.292 4.75,4.583 0.333,0.292 10 false T15 4.688,4.292 6.656,4.594 1.969,0.302 10 false CAN No. 3 Junction Connector 4.99,4.948 5.219,5.24 0.229,0.292 10 false V 4.99,5.708 5.219,6 0.229,0.292 10 false P 5.573,5.615 5.802,5.906 0.229,0.292 10 false 1 5.563,5.021 5.792,5.313 0.229,0.292 10 false 4 5.729,5.042 6.135,5.323 0.406,0.281 10 false CANH 5.729,5.604 6.135,5.885 0.406,0.281 10 false CANL 5.604,5.885 7.063,6.698 1.458,0.813 10 false Rear Television Camera Assembly 4.604,7.042 4.896,7.375 0.292,0.333 10 false T16 2.958,6.26 3.188,6.552 0.229,0.292 10 false B 4.052,6.271 4.281,6.563 0.229,0.292 10 false L 3.042,6.51 3.271,6.802 0.229,0.292 10 false 2 4.042,6.5 4.271,6.792 0.229,0.292 10 false 3 2.771,6.708 3.177,6.99 0.406,0.281 10 false CANL 4.01,6.729 4.417,7.01 0.406,0.281 10 false CANH 4.917,7.042 6.885,7.344 1.969,0.302 10 false CAN No. 4 Junction Connector 0.927,7.958 2.896,8.26 1.969,0.302 10 false : CAN Main Bus Line (CANH) 0.927,8.375 2.896,8.677 1.969,0.302 10 false : CAN Main Bus Line (CANL) 3.594,7.948 5.563,8.25 1.969,0.302 10 false : CAN Branch Line (CANH) 3.594,8.344 5.563,8.646 1.969,0.302 10 false : CAN Branch Line (CANL) 0.219,6.375 2.292,6.615 2.073,0.24 10 false *: w/ Blind Spot Monitor System 5.292,5.885 5.625,6.177 0.333,0.292 10 false T22

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the power switch on (IG), turn the blind spot monitor main switch on, wait at least 11.68 seconds and then drive the vehicle at a speed of 5 km/h (3 mph) or more for at least 11.84 seconds.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM



HINT:
·

Operating the power switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK VEHICLE TYPE
a.

Check vehicle type.


Result:
Result Proceed to
w/o Parking Assist Monitor System without Parallel Parking Assist Function A
w/ Parking Assist Monitor System without Parallel Parking Assist Function B



A

2.CHECK SUB BUS 11

B

16.CHECK SUB BUS 11
2.CHECK SUB BUS 11
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
A261175C43
1.813,0.583 2.313,0.875 0.5,0.292 1.604,1.083 1.698,1.083 1.698,1.083 1.823,1.688 true 2.552,1.083 2.448,1.083 2.448,1.083 2.229,1.688 true 1.531,2.917 1.625,2.917 1.625,2.917 1.813,1.906 true 2.167,2.906 2.083,2.906 2.083,2.906 1.865,1.906 true 0.063,0.021 0.271,0.24 0.208,0.219 10 false *a 2.573,1 2.99,1.156 0.417,0.156 10 false AM22 1.375,1 1.573,1.156 0.198,0.156 10 false E1 1.99,0.635 2.167,0.802 0.177,0.167 10 false I3 1.104,2.823 1.521,2.979 0.417,0.156 10 false CA2L 2.219,2.813 2.635,2.969 0.417,0.156 10 false CA2H
*a Component with harness connector
(Power Management Control ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Result
I3-34 (CA2H) - I3-35 (CA2L) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω Below 54 Ω: Short circuit between bus lines
70 Ω or higher: Open circuit in main bus lines
I3-34 (CA2H) - I3-6 (E1) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω: CANH ground short
I3-35 (CA2L) - I3-6 (E1) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω: CANL ground short
I3-34 (CA2H) - I3-1 (AM22) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ: CANH +B short
I3-35 (CA2L) - I3-1 (AM22) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ: CANL +B short



Result:
Result Proceed to
OK A
NG (Open circuit in CAN main bus lines) B
NG (Short circuit between bus lines) C
·

NG (Ground short)

·

NG (+B short)


D



A

3.CHECK FOR DTC OUTPUT

B

4.CHECK FOR OPEN IN SUB BUS 11 MAIN LINES (POWER MANAGEMENT CONTROL ECU)

C

8.CHECK FOR SHORT IN SUB BUS 11 LINES (POWER MANAGEMENT CONTROL ECU)

D

12.CHECK FOR SHORT IN SUB BUS 11 LINE (CAN NO. 2 JUNCTION CONNECTOR)
3.CHECK FOR DTC OUTPUT
a.

Reconnect the cable to the negative (-) auxiliary battery terminal.


b.

Connect the GTS to the DLC3.


c.

Turn the power switch on (IG).


d.

Turn the GTS on.


e.

Clear the DTCs.

Body Electrical > PM1 Gateway > Clear DTCs
50002 217

f.

Turn the power switch off.


g.

Turn the power switch on (IG).


h.

Check for DTCs.

Body Electrical > PM1 Gateway > Trouble Codes
50001 217

Result:
Result Proceed to
DTC U1002 is output from the power management control ECU (GTS display: PM1 Gateway) A
DTC U1002 is not output from the power management control ECU (GTS display: PM1 Gateway) B



A

B

GO TO DIAGNOSIS PROCEDURE INDICATED BY OUTPUT DTC

4.CHECK FOR OPEN IN SUB BUS 11 MAIN LINES (POWER MANAGEMENT CONTROL ECU)
a.
C285701C24
1.365,0.104 1.771,0.344 0.406,0.24 1.948,1.979 2.083,1.979 2.083,1.979 2.208,1.49 true 2.354,1.479 2.583,1.969 2.583,1.969 2.75,1.969 true 0.146,0.135 0.458,0.333 0.313,0.198 10 false *a 1.521,0.135 1.979,0.333 0.458,0.198 10 false I3 2.823,1.885 3.427,2.094 0.604,0.208 10 false CA2L 1.573,1.896 2.188,2.104 0.615,0.208 10 false CA2H
*a Front view of wire harness connector
(to Power Management Control ECU)


Disconnect the I3 power management control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I3-34 (CA2H) - I3-35 (CA2L) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Result
OK
NG



OK

NG

5.CHECK FOR OPEN IN SUB BUS 11 MAIN LINES (CAN NO. 2 JUNCTION CONNECTOR)
5.CHECK FOR OPEN IN SUB BUS 11 MAIN LINES (CAN NO. 2 JUNCTION CONNECTOR)
a.

Reconnect the I3 power management control ECU connector.


b.
C238890C81
0.469,1.24 0.958,1.5 0.49,0.26 2.521,0.51 2.198,0.51 2.198,0.51 2.198,1.354 true 2.625,0.771 2.302,0.771 2.302,0.771 2.302,1.354 true 2.635,1.885 2.313,1.885 2.313,1.885 2.313,1.573 true 2.031,2.063 2.188,2.063 2.188,2.063 2.188,1.573 true 0.177,0.156 0.323,0.313 0.146,0.156 10 false *a 2.573,0.427 3.125,0.583 0.552,0.156 10 false CANH*b 2.677,0.688 3.229,0.844 0.552,0.156 10 false CANH*c 1.417,1.958 1.969,2.115 0.552,0.156 10 false CANL*b 2.677,1.802 3.229,1.958 0.552,0.156 10 false CANL*c 0.552,1.281 0.833,1.479 0.281,0.198 10 false O30
*a Front view of wire harness connector
(to CAN No. 2 Junction Connector)
*b to CAN No. 3 Junction Connector
*c to Power Management Control ECU


Disconnect the O30 CAN No. 2 junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
O30-10 (CANH) - O30-21 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω CAN No. 3 junction connector
O30-11 (CANH) - O30-22 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω Power management control ECU



Result:
Result Proceed to
OK A
NG (to Power management control ECU main bus lines) B
NG (to CAN No. 3 junction connector main bus lines) C



A

REPLACE CAN NO. 2 JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN NO. 2 JUNCTION CONNECTOR - POWER MANAGEMENT CONTROL ECU)

C

6.CHECK FOR OPEN IN SUB BUS 11 MAIN LINES (CAN NO. 3 JUNCTION CONNECTOR)
6.CHECK FOR OPEN IN SUB BUS 11 MAIN LINES (CAN NO. 3 JUNCTION CONNECTOR)
a.

Reconnect the O30 CAN No. 2 junction connector.


b.
C238890C84
0.479,1.135 0.896,1.375 0.417,0.24 2.396,0.271 2.073,0.271 2.073,0.271 2.073,1.365 true 2.635,0.781 2.313,0.781 2.313,0.781 2.313,1.365 true 2.635,1.896 2.313,1.896 2.313,1.896 2.313,1.583 true 1.26,1.896 2.094,1.896 2.094,1.896 2.094,1.583 true 0.177,0.156 0.323,0.313 0.146,0.156 10 false *a 2.5,0.198 3.052,0.354 0.552,0.156 10 false CANH*b 2.76,0.698 3.313,0.854 0.552,0.156 10 false CANH*c 0.74,1.823 1.292,1.979 0.552,0.156 10 false CANL*b 2.719,1.833 3.271,1.99 0.552,0.156 10 false CANL*c 0.573,1.188 0.969,1.521 0.396,0.333 10 false T15
*a Front view of wire harness connector
(to CAN No. 3 Junction Connector)
*b to CAN No. 4 Junction Connector
*c to CAN No. 2 Junction Connector


Disconnect the T15 CAN No. 3 junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
T15-9 (CANH) - T15-11 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω CAN No. 4 junction connector
T15-11 (CANH) - T15-22 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω CAN No. 2 junction connector



Result:
Result Proceed to
OK A
NG (to CAN No. 2 junction connector main bus lines) B
NG (to CAN No. 4 junction connector main bus lines) C



A

REPLACE CAN NO. 3 JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN NO. 2 JUNCTION CONNECTOR - CAN NO. 3 JUNCTION CONNECTOR)

C

7.CHECK FOR OPEN IN SUB BUS 11 MAIN LINES (CAN NO. 4 JUNCTION CONNECTOR)
7.CHECK FOR OPEN IN SUB BUS 11 MAIN LINES (CAN NO. 4 JUNCTION CONNECTOR)
a.

Reconnect the T15 CAN No. 3 junction connector.


b.
C183982C40
1.781,2.063 2.198,2.302 0.417,0.24 0.938,0.844 0.635,0.844 0.635,0.844 0.635,2.177 true 1.219,1.188 0.917,1.188 0.917,1.188 0.917,2.177 true 0.177,0.115 0.333,0.292 0.156,0.177 10 false *a 0.99,0.75 1.563,0.906 0.573,0.156 10 false CANH*b 1.271,1.104 1.833,1.26 0.563,0.156 10 false CANL*b 1.875,2.104 2.438,2.5 0.563,0.396 10 false T16
*a Rear view of wire harness connector
(to CAN No. 4 Junction Connector)
*b to CAN No. 3 Junction Connector


Disconnect the T16 CAN No. 4 junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
T16-3 (CANH) - T16-2 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Result
OK
NG



OK

REPLACE CAN NO. 4 JUNCTION CONNECTOR

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN NO. 3 JUNCTION CONNECTOR - CAN NO. 4 JUNCTION CONNECTOR)

8.CHECK FOR SHORT IN SUB BUS 11 LINES (POWER MANAGEMENT CONTROL ECU)
a.
C285701C24
1.365,0.104 1.771,0.344 0.406,0.24 1.948,1.979 2.083,1.979 2.083,1.979 2.208,1.49 true 2.354,1.479 2.583,1.969 2.583,1.969 2.75,1.969 true 0.146,0.135 0.458,0.333 0.313,0.198 10 false *a 1.521,0.135 1.979,0.333 0.458,0.198 10 false I3 2.823,1.885 3.427,2.094 0.604,0.208 10 false CA2L 1.573,1.896 2.188,2.104 0.615,0.208 10 false CA2H
*a Rear view of wire harness connector
(to Power Management Control ECU)


Disconnect the I3 power management control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I3-34 (CA2H) - I3-35 (CA2L) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Result
OK
NG



OK

NG

9.CHECK FOR SHORT IN SUB BUS 11 LINES (CAN NO. 2 JUNCTION CONNECTOR)
9.CHECK FOR SHORT IN SUB BUS 11 LINES (CAN NO. 2 JUNCTION CONNECTOR)
a.

Reconnect the I3 power management control ECU connector.


b.
C238890C79
0.406,1.146 0.823,1.385 0.417,0.24 2.427,0.281 2.104,0.281 2.104,0.281 2.104,1.375 true 2.521,0.521 2.198,0.521 2.198,0.521 2.198,1.365 true 2.635,0.781 2.313,0.781 2.313,0.781 2.313,1.365 true 2.635,1.885 2.313,1.885 2.313,1.885 2.313,1.573 true 1.26,1.896 2.094,1.896 2.094,1.896 2.094,1.583 true 2.042,2.073 2.198,2.073 2.198,2.073 2.198,1.583 true 0.177,0.156 0.323,0.313 0.146,0.156 10 false *a 2.448,0.177 3.094,0.354 0.646,0.177 10 false CANH*b 2.563,0.427 3.177,0.615 0.615,0.188 10 false CANH*c 2.698,0.698 3.302,0.906 0.604,0.208 10 false CANH*d 2.677,1.802 3.229,1.958 0.552,0.156 10 false CANL*d 0.698,1.813 1.25,1.969 0.552,0.156 10 false CANL*b 1.385,1.979 1.938,2.135 0.552,0.156 10 false CANL*c 0.49,1.188 0.813,1.354 0.323,0.167 10 false O30
*a Front view of wire harness connector
(to CAN No. 2 Junction Connector)
*b to Blind Spot Monitor Sensor RH
*c to CAN No. 3 Junction Connector
*d to Power Management Control ECU


Disconnect the O30 CAN No. 2 junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
O30-9 (CANH) - O30-20 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Blind spot monitor sensor RH
O30-10 (CANH) - O30-21 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω CAN No. 3 junction connector
O30-11 (CANH) - O30-22 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω Power management control ECU



Result:
Result Proceed to
OK A
NG (to Power management control ECU main bus lines) B
NG (to CAN No. 3 junction connector main bus lines) C
NG (to Blind spot monitor sensor RH branch lines) D



A

REPLACE CAN NO. 2 JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN NO. 2 JUNCTION CONNECTOR - POWER MANAGEMENT CONTROL ECU)

C

10.CHECK FOR SHORT IN SUB BUS 11 LINES (CAN NO. 3 JUNCTION CONNECTOR)

D

26.CHECK FOR SHORT IN SUB BUS 11 LINES (ECU, SENSOR)
10.CHECK FOR SHORT IN SUB BUS 11 LINES (CAN NO. 3 JUNCTION CONNECTOR)
a.

Reconnect the O30 CAN No. 2 junction connector.


b.
C238890C85
0.479,1.135 0.896,1.375 0.417,0.24 2.396,0.271 2.073,0.271 2.073,0.271 2.073,1.365 true 2.521,0.521 2.198,0.521 2.198,0.521 2.198,1.365 true 2.635,0.781 2.313,0.781 2.313,0.781 2.313,1.365 true 2.635,1.896 2.313,1.896 2.313,1.896 2.313,1.583 true 1.25,1.885 2.083,1.885 2.083,1.885 2.083,1.573 true 2.042,2.073 2.198,2.073 2.198,2.073 2.198,1.583 true 0.177,0.156 0.323,0.313 0.146,0.156 10 false *a 2.5,0.198 3.052,0.354 0.552,0.156 10 false CANH*b 2.604,0.448 3.156,0.604 0.552,0.156 10 false CANH*c 2.719,0.708 3.271,0.865 0.552,0.156 10 false CANH*d 2.677,1.813 3.229,1.969 0.552,0.156 10 false CANL*d 0.719,1.813 1.271,1.969 0.552,0.156 10 false CANL*b 1.521,1.99 2.073,2.146 0.552,0.156 10 false CANL*c 0.573,1.188 0.969,1.521 0.396,0.333 10 false T15
*a Front view of wire harness connector
(to CAN No. 3 Junction Connector)
*b to CAN No. 4 Junction Connector
*c to Blind Spot Monitor Sensor LH
*d to CAN No. 2 Junction Connector


Disconnect the T15 CAN No. 3 junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
T15-9 (CANH) - T15-20 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω CAN No. 4 junction connector
T15-10 (CANH) - T15-21 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Blind spot monitor sensor LH
T15-11 (CANH) - T15-22 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω CAN No. 2 junction connector



Result:
Result Proceed to
OK A
NG (to CAN No. 2 junction connector main bus lines) B
NG (to CAN No. 4 junction connector main bus lines) C
NG (to Blind spot monitor sensor LH branch lines) D



A

REPLACE CAN NO. 3 JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN NO. 2 JUNCTION CONNECTOR - CAN NO. 3 JUNCTION CONNECTOR)

C

11.CHECK FOR SHORT IN SUB BUS 11 LINES (CAN NO. 4 JUNCTION CONNECTOR)

D

26.CHECK FOR SHORT IN SUB BUS 11 LINES (ECU, SENSOR)
11.CHECK FOR SHORT IN SUB BUS 11 LINES (CAN NO. 4 JUNCTION CONNECTOR)
a.

Reconnect the T15 CAN No. 3 junction connector.


b.
C183982C40
1.781,2.063 2.198,2.302 0.417,0.24 0.938,0.844 0.635,0.844 0.635,0.844 0.635,2.177 true 1.219,1.188 0.917,1.188 0.917,1.188 0.917,2.177 true 0.177,0.115 0.333,0.292 0.156,0.177 10 false *a 0.99,0.75 1.563,0.906 0.573,0.156 10 false CANH*b 1.271,1.104 1.833,1.26 0.563,0.156 10 false CANL*b 1.875,2.104 2.438,2.5 0.563,0.396 10 false T16
*a Rear view of wire harness connector
(to CAN No. 4 Junction Connector)
*b to CAN No. 3 Junction Connector


Disconnect the T16 CAN No. 4 junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
T16-3 (CANH) - T16-2 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Result
OK
NG



OK

REPLACE CAN NO. 4 JUNCTION CONNECTOR

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN NO. 3 JUNCTION CONNECTOR - CAN NO. 4 JUNCTION CONNECTOR)

12.CHECK FOR SHORT IN SUB BUS 11 LINE (CAN NO. 2 JUNCTION CONNECTOR)
a.

Disconnect the O30 CAN No. 2 junction connector.

C240196C21
2.052,3.771 2.417,3.979 0.365,0.208 2.51,1.469 2.875,1.677 0.365,0.208 3.438,3.615 3.333,3.031 3.333,3.031 3.115,3.031 true 4.188,4.198 4.406,4.448 4.406,4.448 4.688,4.448 true 3.99,1.698 4.24,1.552 4.24,1.552 4.396,1.552 true 4,1.854 4.25,1.958 4.25,1.958 4.406,1.958 true 3.896,1.865 4.344,2.302 4.344,2.302 4.573,2.302 true 3.896,1.698 4.354,1.188 4.354,1.188 4.552,1.188 true 3.802,1.698 4.125,0.875 4.125,0.875 4.74,0.875 true 3.802,1.865 4.177,2.635 4.177,2.635 4.771,2.635 true 2.24,0.604 2.531,0.896 0.292,0.292 10 false *a 2.24,2.854 2.531,3.146 0.292,0.292 10 false *1 4.802,0.771 5.51,1.01 0.708,0.24 10 false CANH*b 4.604,1.094 5.313,1.333 0.708,0.24 10 false CANH*c 4.469,1.458 5.177,1.698 0.708,0.24 10 false CANH*d 4.844,2.542 5.552,2.781 0.708,0.24 10 false CANL*b 4.625,2.219 5.333,2.458 0.708,0.24 10 false CANL*c 4.469,1.865 5.177,2.104 0.708,0.24 10 false CANL*d 2.552,1.479 2.875,1.698 0.323,0.219 10 false O30 2.146,3.781 2.5,4 0.354,0.219 10 false I39 2.865,2.958 3.156,3.177 0.292,0.219 10 false CG 4.74,4.354 5.115,4.563 0.375,0.208 10 false BAT
*1 DLC3 - -
*a Front view of wire harness connector
(to CAN No. 2 Junction Connector)
*b to Blind Spot Monitor Sensor RH
*c to CAN No. 3 Junction Connector *d to Power Management Control ECU



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Result Connected to
O30-9 (CANH) - I39-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω: CANH ground short Blind spot monitor sensor RH
O30-20 (CANL) - I39-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω: CANL ground short
O30-10 (CANH) - I39-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω: CANH ground short CAN No. 3 junction connector
O30-21 (CANL) - I39-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω: CANL ground short
O30-11 (CANH) - I39-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω: CANH ground short Power management control ECU
O30-22 (CANL) - I39-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω: CANL ground short
O30-9 (CANH) - I39-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ: CANH +B short Blind spot monitor sensor RH
O30-20 (CANL) - I39-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ: CANL +B short
O30-10 (CANH) - I39-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ: CANH +B short CAN No. 3 junction connector
O30-21 (CANL) - I39-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ: CANL +B short
O30-11 (CANH) - I39-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ: CANH +B short Power management control ECU
O30-22 (CANL) - I39-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ: CANL +B short



Result:
Result Proceed to
OK A
NG (to Power management control ECU main bus line) B
NG (to CAN No. 3 junction connector main bus line) C
NG (to Blind spot monitor sensor RH branch line) D


HINT:
·

It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 11 inspection.

·

Find the necessary inspection from the Result column that matches the result in the Result column from the Check Sub Bus 11 inspection.




A

REPLACE CAN NO. 2 JUNCTION CONNECTOR

B

13.CHECK FOR SHORT IN SUB BUS 11 LINE (POWER MANAGEMENT CONTROL ECU)

C

14.CHECK FOR SHORT IN SUB BUS 11 LINE (CAN NO. 3 JUNCTION CONNECTOR)

D

31.CHECK FOR SHORT IN SUB BUS 11 LINE (ECU, SENSOR)
13.CHECK FOR SHORT IN SUB BUS 11 LINE (POWER MANAGEMENT CONTROL ECU)
a.
C285701C25
1.365,0.104 1.771,0.344 0.406,0.24 1.948,1.979 2.083,1.979 2.083,1.979 2.208,1.49 true 2.354,1.49 2.583,1.979 2.583,1.979 2.75,1.979 true 2.375,0.875 2.76,0.698 true 0.677,0.698 1.104,0.875 true 0.146,0.135 0.458,0.333 0.313,0.198 10 false *a 1.51,0.135 1.938,0.333 0.427,0.198 10 false I3 2.823,1.885 3.427,2.094 0.604,0.208 10 false CA2L 1.573,1.896 2.188,2.104 0.615,0.208 10 false CA2H 2.823,0.573 3.146,0.792 0.323,0.219 10 false E1 0.26,0.594 0.885,0.885 0.625,0.292 10 false AM22
*a Front view of wire harness connector
(to Power Management Control ECU)


Disconnect the I3 power management control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Result
I3-34 (CA2H) - I3-6 (E1) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω: CANH ground short
I3-35 (CA2L) - I3-6 (E1) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω: CANL ground short
I3-34 (CA2H) - I3-1 (AM22) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ: CANH +B short
I3-35 (CA2L) - I3-1 (AM22) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ: CANL +B short



Result:
Result
OK
NG


HINT:
·

It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 11 inspection.

·

Find the necessary inspection from the Result column that matches the result in the Result column from the Check Sub Bus 11 inspection.




OK

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN NO. 2 JUNCTION CONNECTOR - POWER MANAGEMENT CONTROL ECU)

14.CHECK FOR SHORT IN SUB BUS 11 LINE (CAN NO. 3 JUNCTION CONNECTOR)
a.

Disconnect the T15 CAN No. 3 junction connector.

C240196C23
2.052,3.771 2.417,3.979 0.365,0.208 2.406,1.469 2.771,1.677 0.365,0.208 3.438,3.604 3.26,3.063 3.26,3.063 3.042,3.063 true 4.188,4.219 4.5,4.375 4.5,4.375 4.781,4.375 true 4.01,1.698 4.375,1.51 4.375,1.51 4.531,1.51 true 4.021,1.844 4.344,1.969 4.344,1.969 4.552,1.969 true 3.896,1.865 4.469,2.229 4.469,2.229 4.698,2.229 true 3.896,1.698 4.458,1.125 4.458,1.125 4.656,1.125 true 3.792,1.688 4.229,0.802 4.229,0.802 4.844,0.802 true 3.802,1.865 4.281,2.563 4.281,2.563 4.875,2.563 true 2.24,0.604 2.531,0.896 0.292,0.292 10 false *a 2.24,2.854 2.531,3.146 0.292,0.292 10 false *1 4.917,0.719 5.625,0.958 0.708,0.24 10 false CANH*b 4.781,1.031 5.49,1.271 0.708,0.24 10 false CANH*c 4.604,1.438 5.313,1.677 0.708,0.24 10 false CANH*d 4.979,2.479 5.688,2.719 0.708,0.24 10 false CANL*b 4.781,2.146 5.49,2.385 0.708,0.24 10 false CANL*c 4.667,1.875 5.375,2.115 0.708,0.24 10 false CANL*d 2.458,1.5 2.781,1.719 0.323,0.219 10 false T15 2.146,3.802 2.5,4.021 0.354,0.219 10 false I39 2.813,2.99 3.104,3.208 0.292,0.219 10 false CG 4.802,4.292 5.177,4.5 0.375,0.208 10 false BAT
*1 DLC3 - -
*a Front view of wire harness connector
(to CAN No. 3 Junction Connector)
*b to CAN No. 4 Junction Connector
*c to Blind Spot Monitor Sensor LH *d to CAN No. 2 Junction Connector



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Result Connected to
T15-9 (CANH) - I39-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω: CANH ground short CAN No. 4 junction connector
T15-20 (CANL) - I39-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω: CANL ground short
T15-10 (CANH) - I39-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω: CANH ground short Blind spot monitor sensor LH
T15-21 (CANL) - I39-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω: CANL ground short
T15-11 (CANH) - I39-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω: CANH ground short CAN No. 2 junction connector
T15-22 (CANL) - I39-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω: CANL ground short
T15-9 (CANH) - I39-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ: CANH +B short CAN No. 4 junction connector
T15-20 (CANL) - I39-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ: CANL +B short
T15-10 (CANH) - I39-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ: CANH +B short Blind spot monitor sensor LH
T15-21 (CANL) - I39-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ: CANL +B short
T15-11 (CANH) - I39-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ: CANH +B short CAN No. 2 junction connector
T15-22 (CANL) - I39-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ: CANL +B short



Result:
Result Proceed to
OK A
NG (to CAN No. 2 junction connector main bus line) B
NG (to CAN No. 4 junction connector main bus line) C
NG (to Blind spot monitor sensor LH branch line) D


HINT:
·

It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 11 inspection.

·

Find the necessary inspection from the Result column that matches the result in the Result column from the Check Sub Bus 11 inspection.




A

REPLACE CAN NO. 3 JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN NO. 2 JUNCTION CONNECTOR - CAN NO. 3 JUNCTION CONNECTOR)

C

15.CHECK FOR SHORT IN SUB BUS 11 LINE (CAN NO. 4 JUNCTION CONNECTOR)

D

31.CHECK FOR SHORT IN SUB BUS 11 LINE (ECU, SENSOR)
15.CHECK FOR SHORT IN SUB BUS 11 LINE (CAN NO. 4 JUNCTION CONNECTOR)
a.
C274535C10
1.51,0.302 1.948,0.646 0.438,0.344 1.563,2.146 2,2.49 0.438,0.344 2.104,1.302 2.104,1.875 2.104,1.875 2.385,1.875 true 1.823,1.302 1.823,1.875 1.823,1.875 1.406,1.875 true 2.76,4.115 2.552,4.115 2.552,4.115 2.552,3.802 true 1.677,3.094 1.667,2.677 1.667,2.677 1.469,2.677 true 2.448,1.802 3.01,2.125 0.563,0.323 10 false CANH 1,1.802 1.625,2.135 0.625,0.333 10 false CANL 0.135,0.146 0.563,0.448 0.427,0.302 10 false *a 2.865,4.021 3.26,4.281 0.396,0.26 10 false BAT 1.177,2.573 1.708,2.896 0.531,0.323 10 false CG 1.604,0.396 2.063,0.708 0.458,0.313 10 false T16 1.688,2.24 2.146,2.552 0.458,0.313 10 false I39 0.188,2.479 0.615,2.781 0.427,0.302 10 false *1
*1 DLC3
*a Front view of wire harness connector
(to CAN No. 4 Junction Connector)


Disconnect the T16 CAN No. 4 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Result
T16-3 (CANH) - I39-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω: CANH ground short
T16-2 (CANL) - I39-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω: CANL ground short
T16-3 (CANH) - I39-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ: CANH +B short
T16-2 (CANL) - I39-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ: CANL +B short


HINT:
·

It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 11 inspection.

·

Find the necessary inspection from the Result column that matches the result in the Result column from the Check Sub Bus 11 inspection.




Result:
Result
OK
NG



OK

REPLACE CAN NO. 4 JUNCTION CONNECTOR

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN NO. 3 JUNCTION CONNECTOR - CAN NO. 4 JUNCTION CONNECTOR)

16.CHECK SUB BUS 11
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
A261175C43
1.813,0.583 2.313,0.875 0.5,0.292 1.604,1.083 1.698,1.083 1.698,1.083 1.823,1.688 true 2.552,1.083 2.448,1.083 2.448,1.083 2.229,1.688 true 1.531,2.917 1.625,2.917 1.625,2.917 1.813,1.906 true 2.167,2.906 2.083,2.906 2.083,2.906 1.865,1.906 true 0.063,0.021 0.271,0.24 0.208,0.219 10 false *a 2.573,1 2.99,1.156 0.417,0.156 10 false AM22 1.375,1 1.573,1.156 0.198,0.156 10 false E1 1.99,0.635 2.167,0.802 0.177,0.167 10 false I3 1.104,2.823 1.521,2.979 0.417,0.156 10 false CA2L 2.219,2.813 2.635,2.969 0.417,0.156 10 false CA2H
*a Component with harness connector
(Power Management Control ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Result
I3-34 (CA2H) - I3-35 (CA2L) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω Below 54 Ω: Short circuit between bus lines
70 Ω or higher: Open circuit in main bus lines
I3-34 (CA2H) - I3-6 (E1) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω: CANH ground short
I3-35 (CA2L) - I3-6 (E1) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω: CANL ground short
I3-34 (CA2H) - I3-1 (AM22) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ: CANH +B short
I3-35 (CA2L) - I3-1 (AM22) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ: CANL +B short



Result:
Result Proceed to
OK A
NG (Open circuit in CAN main bus lines) B
NG (Short circuit between bus lines) C
·

NG (Ground short)

·

NG (+B short)


D



A

17.CHECK FOR DTC OUTPUT

B

18.CHECK FOR OPEN IN SUB BUS 11 MAIN LINES (POWER MANAGEMENT CONTROL ECU)

C

22.CHECK FOR SHORT IN SUB BUS 11 LINES (POWER MANAGEMENT CONTROL ECU)

D

27.CHECK FOR SHORT IN SUB BUS 11 LINE (CAN NO. 2 JUNCTION CONNECTOR)
17.CHECK FOR DTC OUTPUT
a.

Reconnect the cable to the negative (-) auxiliary battery terminal.


b.

Connect the GTS to the DLC3.


c.

Turn the power switch on (IG).


d.

Turn the GTS on.


e.

Clear the DTCs.

Body Electrical > PM1 Gateway > Clear DTCs
50002 217

f.

Turn the power switch off.


g.

Turn the power switch on (IG).


h.

Check for DTCs.

Body Electrical > PM1 Gateway > Trouble Codes
50001 217

Result:
Result Proceed to
DTC U1002 is output from the power management control ECU (GTS display: PM1 Gateway) A
DTC U1002 is not output from the power management control ECU (GTS display: PM1 Gateway) B



A

B

GO TO DIAGNOSIS PROCEDURE INDICATED BY OUTPUT DTC

18.CHECK FOR OPEN IN SUB BUS 11 MAIN LINES (POWER MANAGEMENT CONTROL ECU)
a.
C285701C24
1.365,0.104 1.771,0.344 0.406,0.24 1.948,1.979 2.083,1.979 2.083,1.979 2.208,1.49 true 2.354,1.479 2.583,1.969 2.583,1.969 2.75,1.969 true 0.146,0.135 0.458,0.333 0.313,0.198 10 false *a 1.521,0.135 1.979,0.333 0.458,0.198 10 false I3 2.823,1.885 3.427,2.094 0.604,0.208 10 false CA2L 1.573,1.896 2.188,2.104 0.615,0.208 10 false CA2H
*a Front view of wire harness connector
(to Power Management Control ECU)


Disconnect the I3 power management control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I3-34 (CA2H) - I3-35 (CA2L) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Result
OK
NG



OK

NG

19.CHECK FOR OPEN IN SUB BUS 11 MAIN LINES (CAN NO. 2 JUNCTION CONNECTOR)
19.CHECK FOR OPEN IN SUB BUS 11 MAIN LINES (CAN NO. 2 JUNCTION CONNECTOR)
a.

Reconnect the I3 power management control ECU connector.


b.
C238890C81
0.469,1.24 0.958,1.5 0.49,0.26 2.521,0.51 2.198,0.51 2.198,0.51 2.198,1.354 true 2.625,0.771 2.302,0.771 2.302,0.771 2.302,1.354 true 2.635,1.885 2.313,1.885 2.313,1.885 2.313,1.573 true 2.031,2.063 2.188,2.063 2.188,2.063 2.188,1.573 true 0.177,0.156 0.323,0.313 0.146,0.156 10 false *a 2.573,0.427 3.125,0.583 0.552,0.156 10 false CANH*b 2.677,0.688 3.229,0.844 0.552,0.156 10 false CANH*c 1.417,1.958 1.969,2.115 0.552,0.156 10 false CANL*b 2.677,1.802 3.229,1.958 0.552,0.156 10 false CANL*c 0.552,1.281 0.833,1.479 0.281,0.198 10 false O30
*a Front view of wire harness connector
(to CAN No. 2 Junction Connector)
*b to CAN No. 3 Junction Connector
*c to Power Management Control ECU


Disconnect the O30 CAN No. 2 junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
O30-10 (CANH) - O30-21 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω CAN No. 3 junction connector
O30-11 (CANH) - O30-22 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω Power management control ECU



Result:
Result Proceed to
OK A
NG (to Power management control ECU main bus lines) B
NG (to CAN No. 3 junction connector main bus lines) C



A

REPLACE CAN NO. 2 JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN NO. 2 JUNCTION CONNECTOR - POWER MANAGEMENT CONTROL ECU)

C

20.CHECK FOR OPEN IN SUB BUS 11 MAIN LINES (CAN NO. 3 JUNCTION CONNECTOR)
20.CHECK FOR OPEN IN SUB BUS 11 MAIN LINES (CAN NO. 3 JUNCTION CONNECTOR)
a.

Reconnect the O30 CAN No. 2 junction connector.


b.
C238890C83
0.479,1.188 0.958,1.438 0.479,0.25 1.26,0.51 1.5,0.51 1.5,0.51 1.5,1.354 true 0.896,0.771 1.271,0.771 1.271,0.771 1.271,1.354 true 1.833,1.885 1.51,1.885 1.51,1.885 1.51,1.573 true 1.135,2.063 1.292,2.063 1.292,2.063 1.292,1.573 true 0.177,0.156 0.323,0.313 0.146,0.156 10 false *a 0.333,0.698 0.885,0.854 0.552,0.156 10 false CANH*b 0.698,0.448 1.25,0.604 0.552,0.156 10 false CANH*c 0.604,1.958 1.156,2.115 0.552,0.156 10 false CANL*b 1.927,1.802 2.479,1.958 0.552,0.156 10 false CANL*c 0.573,1.229 0.854,1.438 0.281,0.208 10 false T15
*a Front view of wire harness connector
(to CAN No. 3 Junction Connector)
*b to CAN No. 4 Junction Connector
*c to CAN No. 2 Junction Connector


Disconnect the T15 CAN No. 3 junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
T15-2 (CANH) - T15-13 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω CAN No. 4 junction connector
T15-4 (CANH) - T15-15 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω CAN No. 2 junction connector



Result:
Result Proceed to
OK A
NG (to CAN No. 2 junction connector main bus lines) B
NG (to CAN No. 4 junction connector main bus lines) C



A

REPLACE CAN NO. 3 JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN NO. 2 JUNCTION CONNECTOR - CAN NO. 3 JUNCTION CONNECTOR)

C

21.CHECK FOR OPEN IN SUB BUS 11 MAIN LINES (CAN NO. 4 JUNCTION CONNECTOR)
21.CHECK FOR OPEN IN SUB BUS 11 MAIN LINES (CAN NO. 4 JUNCTION CONNECTOR)
a.

Reconnect the T15 CAN No. 3 junction connector.


b.
C183982C40
1.781,2.063 2.198,2.302 0.417,0.24 0.938,0.844 0.635,0.844 0.635,0.844 0.635,2.177 true 1.219,1.188 0.917,1.188 0.917,1.188 0.917,2.177 true 0.177,0.115 0.333,0.292 0.156,0.177 10 false *a 0.99,0.75 1.563,0.906 0.573,0.156 10 false CANH*b 1.271,1.104 1.833,1.26 0.563,0.156 10 false CANL*b 1.875,2.104 2.438,2.5 0.563,0.396 10 false T16
*a Rear view of wire harness connector
(to CAN No. 4 Junction Connector)
*b to CAN No. 3 Junction Connector


Disconnect the T16 CAN No. 4 junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
T16-3 (CANH) - T16-2 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Result
OK
NG



OK

REPLACE CAN NO. 4 JUNCTION CONNECTOR

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN NO. 3 JUNCTION CONNECTOR - CAN NO. 4 JUNCTION CONNECTOR)

22.CHECK FOR SHORT IN SUB BUS 11 LINES (POWER MANAGEMENT CONTROL ECU)
a.
C285701C24
1.365,0.104 1.771,0.344 0.406,0.24 1.948,1.979 2.083,1.979 2.083,1.979 2.208,1.49 true 2.354,1.479 2.583,1.969 2.583,1.969 2.75,1.969 true 0.146,0.135 0.458,0.333 0.313,0.198 10 false *a 1.521,0.135 1.979,0.333 0.458,0.198 10 false I3 2.823,1.885 3.427,2.094 0.604,0.208 10 false CA2L 1.573,1.896 2.188,2.104 0.615,0.208 10 false CA2H
*a Rear view of wire harness connector
(to Power Management Control ECU)


Disconnect the I3 power management control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I3-34 (CA2H) - I3-35 (CA2L) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Result
OK
NG



OK

NG

23.CHECK FOR SHORT IN SUB BUS 11 LINES (CAN NO. 2 JUNCTION CONNECTOR)
23.CHECK FOR SHORT IN SUB BUS 11 LINES (CAN NO. 2 JUNCTION CONNECTOR)
a.

Reconnect the I3 power management control ECU connector.


b.
C238890C79
0.406,1.146 0.823,1.385 0.417,0.24 2.427,0.281 2.104,0.281 2.104,0.281 2.104,1.375 true 2.521,0.521 2.198,0.521 2.198,0.521 2.198,1.365 true 2.635,0.781 2.313,0.781 2.313,0.781 2.313,1.365 true 2.635,1.885 2.313,1.885 2.313,1.885 2.313,1.573 true 1.26,1.896 2.094,1.896 2.094,1.896 2.094,1.583 true 2.042,2.073 2.198,2.073 2.198,2.073 2.198,1.583 true 0.177,0.156 0.323,0.313 0.146,0.156 10 false *a 2.448,0.177 3.094,0.354 0.646,0.177 10 false CANH*b 2.563,0.427 3.177,0.615 0.615,0.188 10 false CANH*c 2.698,0.698 3.302,0.906 0.604,0.208 10 false CANH*d 2.677,1.802 3.229,1.958 0.552,0.156 10 false CANL*d 0.698,1.813 1.25,1.969 0.552,0.156 10 false CANL*b 1.385,1.979 1.938,2.135 0.552,0.156 10 false CANL*c 0.49,1.188 0.813,1.354 0.323,0.167 10 false O30
*a Front view of wire harness connector
(to CAN No. 2 Junction Connector)
*b to Blind Spot Monitor Sensor RH
(w/ Blind Spot Monitor System)
*c to CAN No. 3 Junction Connector
*d to Power Management Control ECU


Disconnect the O30 CAN No. 2 junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
O30-9 (CANH) - O30-20 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Blind spot monitor sensor RH*
O30-10 (CANH) - O30-21 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω CAN No. 3 junction connector
O30-11 (CANH) - O30-22 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω Power management control ECU


*: w/ Blind Spot Monitor System



Result:
Result Proceed to
OK A
NG (to Power management control ECU main bus lines) B
NG (to CAN No. 3 junction connector main bus lines) C
NG (to Blind spot monitor sensor RH branch lines) D



A

REPLACE CAN NO. 2 JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN NO. 2 JUNCTION CONNECTOR - POWER MANAGEMENT CONTROL ECU)

C

24.CHECK FOR SHORT IN SUB BUS 11 LINES (CAN NO. 3 JUNCTION CONNECTOR)

D

26.CHECK FOR SHORT IN SUB BUS 11 LINES (ECU, SENSOR)
24.CHECK FOR SHORT IN SUB BUS 11 LINES (CAN NO. 3 JUNCTION CONNECTOR)
a.

Reconnect the O30 CAN No. 2 junction connector.


b.
C238890C80
2.604,1.177 3.021,1.417 0.417,0.24 1.823,0.26 1.5,0.26 1.5,0.26 1.5,1.354 true 1.021,0.521 1.281,0.521 1.281,0.521 1.281,1.365 true 0.906,0.781 1.167,0.781 1.167,0.781 1.167,1.365 true 1.833,1.896 1.51,1.896 1.51,1.896 1.51,1.583 true 0.74,1.896 1.167,1.896 1.167,1.896 1.167,1.583 true 1.125,2.073 1.281,2.073 1.281,2.073 1.281,1.583 true 1.583,2.073 1.396,2.073 1.396,2.073 1.396,1.583 true 1.188,0.26 1.385,0.26 1.385,0.26 1.385,1.354 true 0.177,0.156 0.323,0.313 0.146,0.156 10 false *a 0.354,0.719 0.906,0.875 0.552,0.156 10 false CANH*b 0.438,0.448 0.99,0.604 0.552,0.156 10 false CANH*c 0.615,0.198 1.167,0.354 0.552,0.156 10 false CANH*d 1.917,1.813 2.469,1.969 0.552,0.156 10 false CANL*e 0.146,1.823 0.698,1.979 0.552,0.156 10 false CANL*b 0.552,1.99 1.104,2.146 0.552,0.156 10 false CANL*c 2.708,1.219 3.104,1.552 0.396,0.333 10 false T15 1.677,1.979 2.229,2.135 0.552,0.156 10 false CANL*d 1.906,0.177 2.458,0.333 0.552,0.156 10 false CANH*e
*a Front view of wire harness connector
(to CAN No. 3 Junction Connector)
*b to Rear Television Camera Assembly
*c to CAN No. 4 Junction Connector
*d to Blind Spot Monitor Sensor LH
(w/ Blind Spot Monitor System)
*e to CAN No. 2 Junction Connector


Disconnect the T15 CAN No. 3 junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
T15-1 (CANH) - T15-12 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Rear television camera assembly
T15-2 (CANH) - T15-13 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω CAN No. 4 junction connector
T15-3 (CANH) - T15-14 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Blind spot monitor sensor LH*
T15-4 (CANH) - T15-15 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω CAN No. 2 junction connector


*: w/ Blind Spot Monitor System



Result:
Result Proceed to
OK A
NG (to CAN No. 2 junction connector main bus lines) B
NG (to CAN No. 4 junction connector main bus lines) C
NG (to Blind spot monitor sensor LH or rear television camera assembly branch lines) D



A

REPLACE CAN NO. 3 JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN NO. 2 JUNCTION CONNECTOR - CAN NO. 3 JUNCTION CONNECTOR)

C

25.CHECK FOR SHORT IN SUB BUS 11 LINES (CAN NO. 4 JUNCTION CONNECTOR)

D

26.CHECK FOR SHORT IN SUB BUS 11 LINES (ECU, SENSOR)
25.CHECK FOR SHORT IN SUB BUS 11 LINES (CAN NO. 4 JUNCTION CONNECTOR)
a.

Reconnect the T15 CAN No. 3 junction connector.


b.
C183982C40
1.781,2.063 2.198,2.302 0.417,0.24 0.938,0.844 0.635,0.844 0.635,0.844 0.635,2.177 true 1.219,1.188 0.917,1.188 0.917,1.188 0.917,2.177 true 0.177,0.115 0.333,0.292 0.156,0.177 10 false *a 0.99,0.75 1.563,0.906 0.573,0.156 10 false CANH*b 1.271,1.104 1.833,1.26 0.563,0.156 10 false CANL*b 1.875,2.104 2.438,2.5 0.563,0.396 10 false T16
*a Rear view of wire harness connector
(to CAN No. 4 Junction Connector)
*b to CAN No. 3 Junction Connector


Disconnect the T16 CAN No. 4 junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
T16-3 (CANH) - T16-2 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Result
OK
NG



OK

REPLACE CAN NO. 4 JUNCTION CONNECTOR

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN NO. 3 JUNCTION CONNECTOR - CAN NO. 4 JUNCTION CONNECTOR)

26.CHECK FOR SHORT IN SUB BUS 11 LINES (ECU, SENSOR)
a.

Reconnect all wire harness connectors.


b.

Disconnect the connector that includes terminals CANH and CANL from the ECU or sensor to which the short-circuited branch line is connected.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>TERMINALS OF ECU


c.
A261175C44
1.813,0.583 2.313,0.875 0.5,0.292 1.531,2.917 1.625,2.917 1.625,2.917 1.813,1.906 true 2.167,2.906 2.083,2.906 2.083,2.906 1.865,1.906 true 0.063,0.021 0.271,0.24 0.208,0.219 10 false *a 1.99,0.635 2.167,0.802 0.177,0.167 10 false I3 1.104,2.823 1.531,3.042 0.427,0.219 10 false CA2L 2.219,2.813 2.646,3 0.427,0.188 10 false CA2H
*a Component with harness connector
(Power Management Control ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I3-34 (CA2H) - I3-35 (CA2L) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω


HINT:
·

If the resistance becomes normal (between 54 and 69 Ω) when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.

·

If the resistance does not become normal (between 54 and 69 Ω) when the connector is disconnected from the ECU or sensor, repair or replace the short-circuited branch line or connector.




Result:
Result
OK
NG



OK

REPLACE CORRESPONDING ECU OR SENSOR

NG

REPAIR OR REPLACE CORRESPONDING ECU OR SENSOR BRANCH LINES OR CONNECTOR

27.CHECK FOR SHORT IN SUB BUS 11 LINE (CAN NO. 2 JUNCTION CONNECTOR)
a.

Disconnect the O30 CAN No. 2 junction connector.

C240196C21
2.052,3.771 2.417,3.979 0.365,0.208 2.51,1.469 2.875,1.677 0.365,0.208 3.438,3.615 3.333,3.031 3.333,3.031 3.115,3.031 true 4.188,4.198 4.406,4.448 4.406,4.448 4.688,4.448 true 3.99,1.698 4.24,1.552 4.24,1.552 4.396,1.552 true 4,1.854 4.25,1.958 4.25,1.958 4.406,1.958 true 3.896,1.865 4.344,2.302 4.344,2.302 4.573,2.302 true 3.896,1.698 4.354,1.188 4.354,1.188 4.552,1.188 true 3.802,1.698 4.125,0.875 4.125,0.875 4.74,0.875 true 3.802,1.865 4.177,2.635 4.177,2.635 4.771,2.635 true 2.24,0.604 2.531,0.896 0.292,0.292 10 false *a 2.24,2.854 2.531,3.146 0.292,0.292 10 false *1 4.802,0.771 5.51,1.01 0.708,0.24 10 false CANH*b 4.604,1.094 5.313,1.333 0.708,0.24 10 false CANH*c 4.469,1.458 5.177,1.698 0.708,0.24 10 false CANH*d 4.844,2.542 5.552,2.781 0.708,0.24 10 false CANL*b 4.625,2.219 5.333,2.458 0.708,0.24 10 false CANL*c 4.469,1.865 5.177,2.104 0.708,0.24 10 false CANL*d 2.552,1.479 2.875,1.698 0.323,0.219 10 false O30 2.146,3.781 2.5,4 0.354,0.219 10 false I39 2.865,2.958 3.156,3.177 0.292,0.219 10 false CG 4.74,4.354 5.115,4.563 0.375,0.208 10 false BAT
*1 DLC3 - -
*a Front view of wire harness connector
(to CAN No. 2 Junction Connector)
*b to Blind Spot Monitor Sensor RH
(w/ Blind Spot Monitor System)
*c to CAN No. 3 Junction Connector *d to Power Management Control ECU



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Result Connected to
O30-9 (CANH) - I39-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω: CANH ground short Blind spot monitor sensor RH*
O30-20 (CANL) - I39-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω: CANL ground short
O30-10 (CANH) - I39-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω: CANH ground short CAN No. 3 junction connector
O30-21 (CANL) - I39-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω: CANL ground short
O30-11 (CANH) - I39-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω: CANH ground short Power management control ECU
O30-22 (CANL) - I39-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω: CANL ground short
O30-9 (CANH) - I39-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ: CANH +B short Blind spot monitor sensor RH*
O30-20 (CANL) - I39-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ: CANL +B short
O30-10 (CANH) - I39-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ: CANH +B short CAN No. 3 junction connector
O30-21 (CANL) - I39-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ: CANL +B short
O30-11 (CANH) - I39-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ: CANH +B short Power management control ECU
O30-22 (CANL) - I39-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ: CANL +B short


*: w/ Blind Spot Monitor System



Result:
Result Proceed to
OK A
NG (to Power management control ECU main bus line) B
NG (to CAN No. 3 junction connector main bus line) C
NG (to Blind spot monitor sensor RH branch line) D


HINT:
·

It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 11 inspection.

·

Find the necessary inspection from the Result column that matches the result in the Result column from the Check Sub Bus 11 inspection.




A

REPLACE CAN NO. 2 JUNCTION CONNECTOR

B

28.CHECK FOR SHORT IN SUB BUS 11 LINE (POWER MANAGEMENT CONTROL ECU)

C

29.CHECK FOR SHORT IN SUB BUS 11 LINE (CAN NO. 3 JUNCTION CONNECTOR)

D

31.CHECK FOR SHORT IN SUB BUS 11 LINE (ECU, SENSOR)
28.CHECK FOR SHORT IN SUB BUS 11 LINE (POWER MANAGEMENT CONTROL ECU)
a.
C285701C25
1.365,0.104 1.771,0.344 0.406,0.24 1.948,1.979 2.083,1.979 2.083,1.979 2.208,1.49 true 2.354,1.49 2.583,1.979 2.583,1.979 2.75,1.979 true 2.375,0.875 2.76,0.698 true 0.677,0.698 1.104,0.875 true 0.146,0.135 0.458,0.333 0.313,0.198 10 false *a 1.51,0.135 1.938,0.333 0.427,0.198 10 false I3 2.823,1.885 3.427,2.094 0.604,0.208 10 false CA2L 1.573,1.896 2.188,2.104 0.615,0.208 10 false CA2H 2.823,0.573 3.146,0.792 0.323,0.219 10 false E1 0.26,0.594 0.885,0.885 0.625,0.292 10 false AM22
*a Front view of wire harness connector
(to Power Management Control ECU)


Disconnect the I3 power management control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Result
I3-34 (CA2H) - I3-6 (E1) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω: CANH ground short
I3-35 (CA2L) - I3-6 (E1) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω: CANL ground short
I3-34 (CA2H) - I3-1 (AM22) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ: CANH +B short
I3-35 (CA2L) - I3-1 (AM22) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ: CANL +B short



Result:
Result
OK
NG


HINT:
·

It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 11 inspection.

·

Find the necessary inspection from the Result column that matches the result in the Result column from the Check Sub Bus 11 inspection.




OK

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN NO. 2 JUNCTION CONNECTOR - POWER MANAGEMENT CONTROL ECU)

29.CHECK FOR SHORT IN SUB BUS 11 LINE (CAN NO. 3 JUNCTION CONNECTOR)
a.

Disconnect the T15 CAN No. 3 junction connector.

C240196C22
2.052,3.771 2.417,3.979 0.365,0.208 3.281,0.292 3.698,0.51 0.417,0.219 4.167,4.177 4.167,4.542 4.167,4.542 4.448,4.542 true 2.677,1.156 3.042,1.156 3.042,1.156 3.042,1.688 true 2.625,2.104 3.052,2.104 3.052,2.104 3.052,1.875 true 3.073,3.083 3.438,3.083 3.438,3.083 3.438,3.615 true 2.927,0.75 3.229,0.75 3.229,0.75 3.229,1.688 true 2.719,2.281 3.146,2.281 3.146,2.281 3.146,1.865 true 2.771,0.938 3.135,0.938 3.135,0.938 3.135,1.698 true 3.021,0.615 3.323,0.615 3.323,0.615 3.323,1.688 true 2.813,2.448 3.24,2.448 3.24,2.448 3.24,1.865 true 2.896,2.646 3.323,2.646 3.323,2.646 3.323,1.865 true 1.885,0.49 2.177,0.781 0.292,0.292 10 false *a 1.917,2.844 2.208,3.135 0.292,0.292 10 false *1 2.354,0.688 3.063,0.927 0.708,0.24 10 false CANH*d 2.208,0.865 2.917,1.104 0.708,0.24 10 false CANH*c 2.083,1.083 2.792,1.323 0.708,0.24 10 false CANH*b 2.25,2.375 2.958,2.615 0.708,0.24 10 false CANL*d 2.177,2.198 2.885,2.438 0.708,0.24 10 false CANL*c 2.073,2.021 2.781,2.26 0.708,0.24 10 false CANL*b 3.375,0.323 3.698,0.542 0.323,0.219 10 false T15 2.146,3.802 2.5,4.021 0.354,0.219 10 false I39 2.802,3 3.094,3.219 0.292,0.219 10 false CG 4.552,4.469 4.927,4.677 0.375,0.208 10 false BAT 2.438,0.531 3.146,0.771 0.708,0.24 10 false CANH*e 2.365,2.573 3.073,2.813 0.708,0.24 10 false CANL*e
*1 DLC3 - -
*a Front view of wire harness connector
(to CAN No. 3 Junction Connector)
*b to Rear Television Camera Assembly
*c to CAN No. 4 Junction Connector *d to Blind Spot Monitor Sensor LH
(w/ Blind Spot Monitor System)
*e to CAN No. 2 Junction Connector - -



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Result Connected to
T15-1 (CANH) - I39-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω: CANH ground short Rear television camera assembly
T15-12 (CANL) - I39-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω: CANL ground short
T15-2 (CANH) - I39-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω: CANH ground short CAN No. 4 junction connector
T15-13 (CANL) - I39-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω: CANL ground short
T15-3 (CANH) - I39-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω: CANH ground short Blind spot monitor sensor LH*
T15-14 (CANL) - I39-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω: CANL ground short
T15-4 (CANH) - I39-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω: CANH ground short CAN No. 2 junction connector
T15-15 (CANL) - I39-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω: CANL ground short
T15-1 (CANH) - I39-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ: CANH +B short Rear television camera assembly
T15-12 (CANL) - I39-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ: CANL +B short
T15-2 (CANH) - I39-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ: CANH +B short CAN No. 4 junction connector
T15-13 (CANL) - I39-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ: CANL +B short
T15-3 (CANH) - I39-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ: CANH +B short Blind spot monitor sensor LH*
T15-14 (CANL) - I39-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ: CANL +B short
T15-4 (CANH) - I39-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ: CANH +B short CAN No. 2 junction connector
T15-15 (CANL) - I39-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ: CANL +B short


*: w/ Blind Spot Monitor System



Result:
Result Proceed to
OK A
NG (to CAN No. 2 junction connector main bus line) B
NG (to CAN No. 4 junction connector main bus line) C
NG (to Blind spot monitor sensor LH or rear television camera assembly branch line) D


HINT:
·

It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 11 inspection.

·

Find the necessary inspection from the Result column that matches the result in the Result column from the Check Sub Bus 11 inspection.




A

REPLACE CAN NO. 3 JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN NO. 2 JUNCTION CONNECTOR - CAN NO. 3 JUNCTION CONNECTOR)

C

30.CHECK FOR SHORT IN SUB BUS 11 LINE (CAN NO. 4 JUNCTION CONNECTOR)

D

31.CHECK FOR SHORT IN SUB BUS 11 LINE (ECU, SENSOR)
30.CHECK FOR SHORT IN SUB BUS 11 LINE (CAN NO. 4 JUNCTION CONNECTOR)
a.
C274535C10
1.51,0.302 1.948,0.646 0.438,0.344 1.563,2.146 2,2.49 0.438,0.344 2.104,1.302 2.104,1.875 2.104,1.875 2.385,1.875 true 1.823,1.302 1.823,1.875 1.823,1.875 1.406,1.875 true 2.76,4.115 2.552,4.115 2.552,4.115 2.552,3.802 true 1.677,3.094 1.667,2.677 1.667,2.677 1.469,2.677 true 2.448,1.802 3.01,2.125 0.563,0.323 10 false CANH 1,1.802 1.625,2.135 0.625,0.333 10 false CANL 0.135,0.146 0.563,0.448 0.427,0.302 10 false *a 2.865,4.021 3.26,4.281 0.396,0.26 10 false BAT 1.177,2.573 1.708,2.896 0.531,0.323 10 false CG 1.604,0.396 2.063,0.708 0.458,0.313 10 false T16 1.688,2.24 2.146,2.552 0.458,0.313 10 false I39 0.188,2.479 0.615,2.781 0.427,0.302 10 false *1
*1 DLC3
*a Front view of wire harness connector
(to CAN No. 4 Junction Connector)


Disconnect the T16 CAN No. 4 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Result
T16-3 (CANH) - I39-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω: CANH ground short
T16-2 (CANL) - I39-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω: CANL ground short
T16-3 (CANH) - I39-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ: CANH +B short
T16-2 (CANL) - I39-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ: CANL +B short


HINT:
·

It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 11 inspection.

·

Find the necessary inspection from the Result column that matches the result in the Result column from the Check Sub Bus 11 inspection.




Result:
Result
OK
NG



OK

REPLACE CAN NO. 4 JUNCTION CONNECTOR

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN NO. 3 JUNCTION CONNECTOR - CAN NO. 4 JUNCTION CONNECTOR)

31.CHECK FOR SHORT IN SUB BUS 11 LINE (ECU, SENSOR)
a.

Reconnect all wire harness connectors.


b.

Disconnect the connector that includes terminals CANH and CANL from the ECU to which the bus line shorted to B+ or shorted to GND is connected.


c.
A261175C43
1.813,0.583 2.313,0.875 0.5,0.292 1.604,1.083 1.698,1.083 1.698,1.083 1.823,1.688 true 2.552,1.083 2.448,1.083 2.448,1.083 2.229,1.688 true 1.531,2.917 1.625,2.917 1.625,2.917 1.813,1.906 true 2.167,2.906 2.083,2.906 2.083,2.906 1.865,1.906 true 0.063,0.021 0.271,0.24 0.208,0.219 10 false *a 2.573,1 2.99,1.156 0.417,0.156 10 false AM22 1.375,1 1.573,1.156 0.198,0.156 10 false E1 1.99,0.635 2.167,0.802 0.177,0.167 10 false I3 1.104,2.823 1.521,2.979 0.417,0.156 10 false CA2L 2.219,2.813 2.635,2.969 0.417,0.156 10 false CA2H
*a Component with harness connected
(Power Management Control ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Result
I3-34 (CA2H) - I3-6 (E1) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω: CANH ground short
I3-35 (CA2L) - I3-6 (E1) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω: CANL ground short
I3-34 (CA2H) - I3-1 (AM22) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ: CANH +B short
I3-35 (CA2L) - I3-1 (AM22) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ: CANL +B short



Result:
Result
OK
NG


HINT:
·

It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 11 inspection.

·

If the resistance becomes abnormal when an ECU connector is reconnected, there may be a short in the ECU. Find the necessary inspection from the Result column that matches the result in the Result column from the Check Sub Bus 11 inspection.




OK

REPLACE CORRESPONDING ECU

NG

REPAIR OR REPLACE CORRESPONDING ECU OR SENSOR BRANCH LINE OR CONNECTOR