| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Note |
|---|---|---|---|---|
| U0265 | Lost Communication with Parking Assist Monitor Module | No communication from the rear television camera assembly continues. | ·
Rear television camera assembly branch line or connector ·
Power source circuit of rear television camera assembly ·
Rear television camera assembly ground circuit ·
Rear television camera assembly |
The power management control ECU stores DTCs when it detects a communication stop or network communication error for ECUs connected to sub bus 11. |
This diagnostic procedure is for when DTC U0265 is output by the power management control ECU (GTS display: PM1 Gateway).
Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.
DTC check procedure: Turn the power switch on (IG) and wait at least 20 seconds.
After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM
Inspect the fuses for circuits related to this system before performing the following procedure.
Operating the power switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.
Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.
Reconfirm DTCs.
If DTC U1002 is output from Gateway of the power management control ECU, this indicates a sub bus 11 malfunction. Troubleshoot for DTC U1002 and check for malfunctions in sub bus 11.
| Result | Proceed to |
|---|---|
| U1002 is not output from the power management control ECU (GTS display: PM1 Gateway) | A |
| U1002 is output from the power management control ECU (GTS display: PM1 Gateway) | B |
A
B
Disconnect the cable from the negative (-) auxiliary battery terminal.
| *a | Front view of wire harness connector
(to Rear Television Camera Assembly) |
Disconnect the T22 rear television camera assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| T22-4 (CANH) - T22-1 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| Result |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Rear Television Camera Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| T22-5 (CGND) - Body ground | Cable disconnected from negative (-) auxiliary battery terminal | Below 1 Ω |
Reconnect the cable to the negative (-) auxiliary battery terminal.
| *a | Front view of wire harness connector
(to Rear Television Camera Assembly) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| T22-6 (CB+) - Body ground | Power switch on (ACC) | 11 to 14 V |
| Result |
|---|
| OK |
| NG |
OK
NG