Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM › from 2015.04
RM2040EQ _59 Vehicle Exterior _014738 LIGHTING (EXT) _0075173 LIGHTING SYSTEM J

LIGHTING (EXT)  LIGHTING SYSTEM  High Beam Headlight Circuit  


DESCRIPTION

The main body ECU (multiplex network body ECU) controls the high beam headlights via the engine room junction block assembly.

WIRING DIAGRAM

E315841E02
0.115,0.792 1.594,1.031 1.479,0.24 10 false from Auxiliary Battery 0.344,1.219 1.615,1.458 1.271,0.24 10 false from DC/DC Fuse 2.99,0.802 3.469,1.021 0.479,0.219 10 false BATT 2.99,1.229 3.469,1.448 0.479,0.219 10 false ALT 2.969,1.656 3.49,1.875 0.521,0.219 10 false GND1 2.969,2.094 3.49,2.313 0.521,0.219 10 false GND2 3.479,0.833 3.958,1.052 0.479,0.219 10 false DIMS 3.458,1.865 3.938,2.083 0.479,0.219 10 false HLHR 3.49,2.26 3.969,2.479 0.479,0.219 10 false HLHL 2.75,2.583 4.177,3 1.427,0.417 10 false Engine Room Junction Block Assembly 2.615,4.365 4.25,4.573 1.635,0.208 10 false Headlight Assembly LH 2.615,4.188 3.01,4.396 0.396,0.208 10 false A78 2.667,5.906 3.177,6.135 0.51,0.229 10 false A80 2.677,6.073 4.313,6.281 1.635,0.208 10 false Headlight Assembly RH 5.49,3.646 7.156,4.188 1.667,0.542 10 false Main Body ECU (Multiplex Network Body ECU) 5.49,3.49 5.885,3.698 0.396,0.208 10 false MB 5.104,0.823 5.5,1.031 0.396,0.208 10 false 3D 5.104,0.625 5.5,0.833 0.396,0.208 10 false 39 6.031,0.719 6.302,0.927 0.271,0.208 10 false 26 6.313,0.802 6.708,1.01 0.396,0.208 10 false DIM 4.583,1.208 6.25,1.75 1.667,0.542 10 false Instrument Panel Junction Block Assembly 2.635,0.823 3.031,1.031 0.396,0.208 10 false A 2.646,1.24 3.042,1.448 0.396,0.208 10 false B 2.615,1.656 3.01,1.865 0.396,0.208 10 false 1F 2.594,2.104 2.99,2.313 0.396,0.208 10 false 1G 4.01,0.833 4.406,1.042 0.396,0.208 10 false 1F 4,1.854 4.396,2.063 0.396,0.208 10 false 1G 4.01,2.25 4.406,2.458 0.396,0.208 10 false 1F 2.76,3.531 2.99,3.729 0.229,0.198 10 false 6 3.948,3.531 4.177,3.729 0.229,0.198 10 false 5 2.781,5.198 3.01,5.396 0.229,0.198 10 false 6 3.948,5.188 4.177,5.385 0.229,0.198 10 false 5 2.635,0.604 2.865,0.802 0.229,0.198 10 false 1 2.646,1.042 2.875,1.24 0.229,0.198 10 false 1 2.656,1.469 2.885,1.667 0.229,0.198 10 false 3 2.656,1.906 2.885,2.104 0.229,0.198 10 false 4 4.042,0.646 4.271,0.844 0.229,0.198 10 false 5 4.052,1.667 4.281,1.865 0.229,0.198 10 false 5 4.01,2.073 4.24,2.271 0.229,0.198 10 false 18 3.052,3.885 3.823,4.094 0.771,0.208 10 false High Beam 3.063,5.552 3.833,5.76 0.771,0.208 10 false High Beam

PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Main Body / Active Test.


e.

Perform the Active Test according to the display on the intelligent tester.

Body Electrical > Main Body > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Head Light Hi High beam headlights ON/OFF -
Body Electrical > Main Body > Active Test
Tester Display
Head Light Hi
50004 123 15
OK:

The high beam headlights illuminate.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK ENGINE ROOM JUNCTION BLOCK ASSEMBLY
2.CHECK ENGINE ROOM JUNCTION BLOCK ASSEMBLY
a.

Using a voltmeter, check the signal reading of the engine room junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>INTEGRATION RELAY>ON-VEHICLE INSPECTION

OK:

Output signal reading is normal



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (ENGINE ROOM JUNCTION BLOCK ASSEMBLY - POWER SOURCE AND BODY GROUND)

NG

INSPECT ENGINE ROOM JUNCTION BLOCK ASSEMBLY (RESULTS OF SIGNAL READING CHECK)

3.CHECK HARNESS AND CONNECTOR (ENGINE ROOM JUNCTION BLOCK ASSEMBLY - POWER SOURCE AND BODY GROUND)
a.

Remove the engine room junction block assembly from the engine room relay block and junction block assembly.

E230000C11
2.781,2.615 3.094,2.813 0.313,0.198 4.729,2.708 5.042,2.906 0.313,0.198 6.188,3.094 6.5,3.292 0.313,0.198 0.771,3.073 1.083,3.271 0.313,0.198 5.104,3.656 5.271,3.979 false 0.865,3.583 0.792,3.896 false 2.615,3.688 2.552,4.135 false 6.281,3.625 6.219,3.948 false 2.865,2.635 3.271,2.896 0.406,0.26 10 1F 4.802,2.729 5.469,3.125 0.667,0.396 10 1G 6.302,3.115 6.75,3.438 0.448,0.323 10 A 0.875,3.094 1.406,3.469 0.531,0.375 10 B 0.271,0.208 0.688,0.552 0.417,0.344 10 *a 6.083,3.958 6.781,4.323 0.698,0.365 10 BATT 5.115,4 5.823,4.333 0.708,0.333 10 GND2 2.344,4.167 3.24,4.542 0.896,0.375 10 GND1 0.646,3.927 1.5,4.344 0.854,0.417 10 ALT
*a Component without engine room junction block assembly
(Engine Room Relay Block and Junction Block Assembly)
- -



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A-1 (BATT) - Body ground Power switch off 11 to 14 V
B-1 (ALT) - Body ground Power switch off 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1F-3 (GND1) - Body ground Always Below 1 Ω
1G-4 (GND2) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (ENGINE ROOM JUNCTION BLOCK ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (ENGINE ROOM JUNCTION BLOCK ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the 3D instrument panel junction block assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1F-5 - 3D-39 Always Below 1 Ω
3D-39 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.
E182506C05
1.479,0.771 1.969,1.063 0.49,0.292 1.479,2.938 1.969,3.229 0.49,0.292 2.625,3.469 2.625,3.729 false 0.156,0.156 0.938,0.813 0.781,0.656 10 *a 1.625,0.823 2.427,1.354 0.802,0.531 10 3D 1.594,2.99 2.344,3.458 0.75,0.469 10 MB 2.51,3.76 3.083,4.333 0.573,0.573 10 DIM
*a Component without harness connected
(Instrument Panel Junction Block Assembly)


Remove the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3D-39 - MB-26 (DIM) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

6.CHECK ENGINE ROOM JUNCTION BLOCK ASSEMBLY

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

6.CHECK ENGINE ROOM JUNCTION BLOCK ASSEMBLY
a.

Replace the engine room junction block assembly with a new or known good one.

Click herePower Source / Network>POWER DISTRIBUTION>INTEGRATION RELAY>REMOVAL


b.

Check that the high beam headlights operate normally.

OK:

The high beam headlights operate normally.



Result:
Proceed to
OK
NG



OK

END (ENGINE ROOM JUNCTION BLOCK ASSEMBLY WAS DEFECTIVE)

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)