Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › from 2015.04
RM2040EQ _58 Vehicle Interior _014725 METER / GAUGE / DISPLAY _0075073 METER / GAUGE SYSTEM C

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  B150A  Lost Communication with HMI-LAN  


DESCRIPTION

The combination meter assembly receives a text data signal from the navigation receiver assembly*1 or radio and display receiver assembly*2 via local bus communication.

Based on this signal, audio and visual system or navigation system information is displayed on the multi-information display.

This DTC is stored when the combination meter assembly cannot receive the signal.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory Note
B150A Lost Communication with HMI-LAN After the combination meter assembly receives a registration information signal, which is sent by the navigation receiver assembly*1 or radio and display receiver assembly*2 when the power switch is on (ACC), 1 or more times, the combination meter assembly cannot receive the signal for 30 seconds or more.
·

Harness or connector

·

Navigation receiver assembly*1

·

Radio and display receiver assembly*2

·

Combination meter assembly


DTC stored -

*1: for Navigation Receiver Type

*2: for Radio and Display Type


WIRING DIAGRAM

for Navigation Receiver Type


E274272E42
0.813,1.906 3.323,2.229 2.51,0.323 10 false Navigation Receiver Assembly 2.26,0.594 2.448,0.76 0.188,0.167 10 false 4 4.885,0.573 5.094,0.74 0.208,0.167 10 false 19 4.833,1.74 5.198,1.958 0.365,0.219 10 false I18 4.833,1.906 6.781,2.177 1.948,0.271 10 false Combination Meter Assembly 0.813,1.75 1.333,1.99 0.521,0.24 10 false I174 1.792,0.74 2.208,0.906 0.417,0.167 10 false CNL1 5.146,0.74 5.563,0.906 0.417,0.167 10 false MSCL 5.156,1.302 5.573,1.469 0.417,0.167 10 false MSCH 2.26,1.156 2.448,1.333 0.188,0.177 10 false 3 4.885,1.146 5.094,1.333 0.208,0.188 10 false 18 0.979,2.375 3.125,2.646 2.146,0.271 10 false : Local Bus Communication Line 1.771,1.302 2.188,1.469 0.417,0.167 10 false CNH1


for Radio and Display Type


E274272E43
1.073,1.938 3.635,2.323 2.563,0.385 10 false Radio and Display Receiver Assembly 2.26,0.594 2.448,0.76 0.188,0.167 10 false 4 4.875,0.583 5.094,0.792 0.219,0.208 10 false 19 4.833,1.781 5.188,2.031 0.354,0.25 10 false I18 4.833,1.948 7.063,2.323 2.229,0.375 10 false Combination Meter Assembly 1.073,1.771 1.406,1.979 0.333,0.208 10 false I175 1.792,0.74 2.208,0.906 0.417,0.167 10 false CNL1 5.146,0.74 5.563,0.906 0.417,0.167 10 false MSCL 5.156,1.302 5.573,1.469 0.417,0.167 10 false MSCH 2.26,1.156 2.448,1.333 0.188,0.177 10 false 3 4.875,1.146 5.115,1.406 0.24,0.26 10 false 18 0.99,2.385 3.667,2.604 2.677,0.219 10 false : Local Bus Communication Line 1.771,1.302 2.188,1.469 0.417,0.167 10 false CNH1


PROCEDURE

1.CONFIRM VEHICLE TYPE
a.

Choose the model to be inspected.


Result:
Result Proceed to
for Navigation Receiver Type A
for Radio and Display Type B



A

2.CHECK FOR DTC

B

5.CHECK FOR DTC
2.CHECK FOR DTC
a.

Check if navigation system DTCs are output.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM(for SD)>DTC CHECK / CLEAR

Body Electrical > Navigation System > Trouble Codes
50001 212

Result:
Result Proceed to
Navigation system DTCs are not output. A
Navigation system DTCs are output. B



A

3.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - NAVIGATION RECEIVER ASSEMBLY)

B

3.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - NAVIGATION RECEIVER ASSEMBLY)
a.

Disconnect the I18 combination meter assembly connector.


b.

Disconnect the I174 navigation receiver assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I18-19 (MSCL) - I174-4 (CNL1) Always Below 1 Ω
I18-18 (MSCH) - I174-3 (CNH1) Always Below 1 Ω
I18-19 (MSCL) - Body ground Always 10 kΩ or higher
I18-18 (MSCH) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.REPLACE COMBINATION METER ASSEMBLY
a.

Replace the combination meter assembly with a new or known good one.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL


b.

Turn the power switch on (IG) and wait 30 seconds.

NOTICE:

A maximum of 30 seconds is required to send/receive the registration information between the combination meter assembly and navigation receiver assembly.



c.

Operate the steering pad switch assembly and check that the navigation tab illuminates.


d.

Check for DTCs.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR

Body Electrical > Combination Meter > Trouble Codes
50001 122

Result:
Result Proceed to
The navigation tab illuminates and DTC B150A is not output. A
The navigation tab does not illuminate and DTC B150A is output. B



A

END

B

5.CHECK FOR DTC
a.

Check if audio and visual system DTCs are output.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM>DTC CHECK / CLEAR

Body Electrical > Navigation System > Trouble Codes
50001 212

Result:
Result Proceed to
Audio and visual system DTCs are not output. A
Audio and visual system DTCs are output. B



A

6.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - RADIO AND DISPLAY RECEIVER ASSEMBLY)

B

6.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - RADIO AND DISPLAY RECEIVER ASSEMBLY)
a.

Disconnect the I18 combination meter assembly connector.


b.

Disconnect the I175 radio and display receiver assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I18-19 (MSCL) - I175-4 (CNL1) Always Below 1 Ω
I18-18 (MSCH) - I175-3 (CNH1) Always Below 1 Ω
I18-19 (MSCL) - Body ground Always 10 kΩ or higher
I18-18 (MSCH) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.REPLACE COMBINATION METER ASSEMBLY
a.

Replace the combination meter assembly with a new or known good one.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL


b.

Turn the power switch on (IG) and wait 30 seconds.

NOTICE:

A maximum of 30 seconds is required to send/receive the registration information between the combination meter assembly and radio and display receiver assembly.



c.

Check for DTCs.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR

Body Electrical > Combination Meter > Trouble Codes
50001 122

Result:
Result Proceed to
DTC B150A is not output. A
DTC B150A is output. B



A

END

B

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY