Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM › from 2015.04
RM2040EQ _58 Vehicle Interior _014723 THEFT DETERRENT / KEYLESS ENTRY _0075062 ENGINE IMMOBILISER SYSTEM C

THEFT DETERRENT / KEYLESS ENTRY  ENGINE IMMOBILISER SYSTEM  B2799  Engine Immobiliser System Malfunction  


DESCRIPTION

When there are communication malfunctions between the power management control ECU and certification ECU (smart key ECU assembly), or when the communication ID codes do not match, the power management control ECU stores this DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
B2799 Engine Immobiliser System Malfunction Either condition is met (1 trip detection logic*):
·

A malfunction in the communication or communication lines between the power management control ECU and certification ECU (smart key ECU assembly).

·

A matching communication code cannot be verified during communication between the power management control ECU and certification ECU (smart key ECU assembly).


·

Certification ECU (smart key ECU assembly)

·

Power management control ECU

·

Wire harness or connector


DTC Output Confirmation Operation
Either condition is met:
·

10 seconds after a hybrid control system start operation (with the shift lever in P and the brake pedal depressed, the power switch is pressed while carrying the key). If there is a malfunction, the hybrid control system does not start (communication begins within 3 seconds of the hybrid control system start operation, and DTCs are stored after 6 seconds).

·

10 seconds after the power switch is turned on (IG) after reconnecting the cable to the negative (-) auxiliary battery terminal (communication begins within 3 seconds of the power switch being turned on (IG), and DTCs are stored after 6 seconds).



*: Only output while a malfunction is present.


Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Hybrid control system cannot be started -

Related Data List and Active Test
DTC Code Data List and Active Test
B2799 -

WIRING DIAGRAM

B271006E80
0.688,1.927 0.927,2.104 0.24,0.177 10 false I4 0.688,2.073 1.99,2.417 1.302,0.344 10 false Power Management Control ECU 5.5,0.938 5.896,1.125 0.396,0.188 10 false EFIO 5.5,1.396 5.896,1.583 0.396,0.188 10 false EFII 1.469,0.938 1.865,1.125 0.396,0.188 10 false IMI 1.438,1.406 1.833,1.594 0.396,0.188 10 false IMO 1.792,0.854 2.031,1.031 0.24,0.177 10 false 29 1.792,1.302 2.031,1.479 0.24,0.177 10 false 28 5.229,0.844 5.521,1.052 0.292,0.208 10 false 14 5.24,1.333 5.531,1.542 0.292,0.208 10 false 10 5.115,1.917 5.5,2.104 0.385,0.188 10 false I87 5.115,2.083 6.656,2.406 1.542,0.323 10 false Certification ECU (Smart Key ECU Assembly)

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the certification ECU (smart key ECU assembly), refer to the Service Bulletin.

·

After performing repairs, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.



HINT:

When DTC B2799 and the certification ECU (smart key ECU assembly) DTC are output simultaneously, first perform troubleshooting for the certification ECU (smart key ECU assembly) DTC.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - POWER MANAGEMENT CONTROL ECU)
a.

Disconnect the I87 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the I4 power management control ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I87-10 (EFII) - I4-28 (IMO) Always Below 1 Ω
I4-28 (IMO) - Body ground Always 10 kΩ or higher
I87-14 (EFIO) - I4-29 (IMI) Always Below 1 Ω
I4-29 (IMI) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.REGISTER ECU COMMUNICATION ID

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.REGISTER ECU COMMUNICATION ID
a.

Register the ECU communication ID.

HINT:

Refer to the Service Bulletin.



Result:
Proceed to
NEXT



NEXT

3.CLEAR DTC
3.CLEAR DTC
a.

Clear the DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Clear DTCs
50002 234

Result:
Proceed to
NEXT



NEXT

4.CHECK DTC OUTPUT
4.CHECK DTC OUTPUT
a.

Check for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Trouble Codes
50001 234
HINT:

Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.


OK:

DTC B2799 is not output.



Result:
Proceed to
OK
NG



OK

END (ECU COMMUNICATION ID HAS NOT BEEN REGISTERED)

NG

5.REPLACE POWER MANAGEMENT CONTROL ECU
5.REPLACE POWER MANAGEMENT CONTROL ECU
a.

Temporarily replace the power management control ECU with a new or known good one.

Click hereEngine / Hybrid System>2AR-FXE ENGINE CONTROL>ECM>REMOVAL


Result:
Proceed to
NEXT



NEXT

6.CLEAR DTC
6.CLEAR DTC
a.

Clear the DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Clear DTCs
50002 234

Result:
Proceed to
NEXT



NEXT

7.CHECK DTC OUTPUT
7.CHECK DTC OUTPUT
a.

Check for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Trouble Codes
50001 234
HINT:

Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.


OK:

DTC B2799 is not output.



Result:
Proceed to
OK
NG



OK

END (POWER MANAGEMENT WAS DEFECTIVE)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)