When the communication line (IMI - EFIO) between the power management control ECU and certification ECU (smart key ECU assembly) is stuck high, the power management control ECU stores this DTC.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Note |
|---|---|---|---|---|
| B279A | Theft Deterrent System Communication Line High Fixation | The communication line (IMI - EFIO) between the power management control ECU and certification ECU (smart key ECU assembly) is stuck high (1 trip detection logic*). | ·
Wire harness or connector (disconnection or break in wire harness is main cause) ·
Certification ECU (smart key ECU assembly) ·
Power management control ECU |
DTC Output Confirmation Operation
Turn the power switch on (IG) and wait 6 seconds. |
*: Only output while a malfunction is present.
| Vehicle Condition when Malfunction Detected | Fail-safe Operation when Malfunction Detected |
|---|---|
| Hybrid control system cannot be started | Hybrid control system cannot be started |
| DTC Code | Data List and Active Test |
|---|---|
| B279A | - |
When replacing the certification ECU (smart key ECU assembly), refer to the Service Bulletin.
After performing repairs, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.
When DTC B279A and the certification ECU (smart key ECU assembly) DTC are output simultaneously, first perform troubleshooting for the certification ECU (smart key ECU assembly) DTC.
Clear the DTCs.
Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM>DTC CHECK / CLEAR
| Proceed to |
|---|
| NEXT |
NEXT
Turn the power switch on (IG) and wait 10 seconds.
Check for DTCs.
Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC B279A is output. | A |
| DTC B279A and other DTCs are output. | B |
If DTCs other than DTC B279A are output, troubleshoot those DTCs first.
A
B
Turn the power switch off.
Check that the connectors are properly connected to the power management control ECU and certification ECU (smart key ECU assembly).
Connectors are properly connected.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the I87 certification ECU (smart key ECU assembly) connector.
Disconnect the I4 power management control ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I87-14 (EFIO) - I4-29 (IMI) | Always | Below 1 Ω |
| I4-29 (IMI) - Body ground | Always | 10 kΩ or higher |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I4-29 (IMI) - Body ground | Always | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the certification ECU (smart key ECU assembly) with a new one.
Refer to the Service Bulletin.
| Proceed to |
|---|
| NEXT |
NEXT
Register the recognition codes in the ECUs.
Refer to the Service Bulletin.
| Proceed to |
|---|
| NEXT |
NEXT
Register the ECU communication ID.
Refer to the Service Bulletin.
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM>DTC CHECK / CLEAR
| Proceed to |
|---|
| NEXT |
NEXT
Check for DTCs.
Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM>DTC CHECK / CLEAR
Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.
DTC B279A is not output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG