Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › from 2015.04
RM2040EQ _51 Engine / Hybrid System _014692 HYBRID / BATTERY CONTROL _0074885 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P0ADC-226  Hybrid Battery Positive Contactor Control Circuit High  


DESCRIPTION

Refer to the description for DTC P0AE6-225 (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0AE6-225).

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P0ADC-226 Hybrid Battery Positive Contactor Control Circuit High Open or short to +B in the SMRB circuit
·

Wire harness or connector

·

Hybrid battery junction block assembly

·

Power management control ECU


Does not come on Master Warning Light:
Comes on

WIRING DIAGRAM

Refer to the wiring diagram for DTC P0AE6-225 (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0AE6-225).

CAUTION / NOTICE / HINT

CAUTION:
·

Before inspecting the high-voltage system or disconnecting the low voltage connector of the inverter with converter assembly, take safety precautions such as wearing insulated gloves and removing the service plug grip to prevent electrical shocks. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·

After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work (See pageEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION).

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.




NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


HINT:

If P0ADC-226 is stored, the vehicle cannot be started.


PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (SMRB STATUS)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Data List / SMRB Status.

Powertrain > Hybrid Control > Data List
Tester Display
SMRB Status
50003 236 510

d.

Read the Data List.

OK:
Tester Display Switch Condition Specified Condition
SMRB Status Power switch on (IG) OFF



e.

Turn the power switch off.

Result:
Proceed to
OK
NG




OK

2.CHECK CONNECTOR CONNECTION CONDITION (POWER MANAGEMENT CONTROL ECU CONNECTOR)

NG

4.CHECK HARNESS AND CONNECTOR (SMRB VOLTAGE)
2.CHECK CONNECTOR CONNECTION CONDITION (POWER MANAGEMENT CONTROL ECU CONNECTOR)

OK

3.CHECK CONNECTOR CONNECTION CONDITION (HYBRID BATTERY JUNCTION BLOCK ASSEMBLY CONNECTOR)

NG

CONNECT SECURELY

3.CHECK CONNECTOR CONNECTION CONDITION (HYBRID BATTERY JUNCTION BLOCK ASSEMBLY CONNECTOR)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 4 hybrid battery shield panel (Click here Engine / Hybrid System>HYBRID / BATTERY CONTROL>HV RELAY ASSEMBLY>REMOVAL).


c.
A259726

Check the connector connections and contact pressure of the relevant terminals for the hybrid battery junction block assembly connector (Click here General>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE).

OK:

The connector is connected securely and there are no contact pressure problems.



d.

Install the No. 4 hybrid battery shield panel.

Result:
Proceed to
OK
NG




OK

NG

CONNECT SECURELY

4.CHECK HARNESS AND CONNECTOR (SMRB VOLTAGE)
a.

Turn the power switch on (IG).


b.
A249277C24
1.896,0.958 2.26,1.198 0.365,0.24 2.021,1.698 1.594,2.448 true 2.031,0.99 2.24,1.156 0.208,0.167 10 false I3 0.135,0.208 0.406,0.375 0.271,0.167 10 false *a 1.344,2.479 1.844,2.646 0.5,0.167 10 false SMRB
*a Component with harness connected
(Power Management Control ECU)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
I3-4 (SMRB) - Body ground Power switch on (IG) Below 1 V



c.

Turn the power switch off.

Result:
Proceed to
OK
NG




OK

5.CHECK CONNECTOR CONNECTION CONDITION (POWER MANAGEMENT CONTROL ECU CONNECTOR)

NG

6.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - BODY GROUND)
5.CHECK CONNECTOR CONNECTION CONDITION (POWER MANAGEMENT CONTROL ECU CONNECTOR)

OK

NG

CONNECT SECURELY

6.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - BODY GROUND)
a.

Disconnect connector I3 from the power management control ECU.


b.
A204445C79
2.583,2.177 3.073,2.469 0.49,0.292 2.042,2.375 1.531,2.615 true 2.781,2.229 3.135,2.406 0.354,0.177 10 false I3 1.094,2.552 1.531,2.729 0.438,0.177 10 false SMRB 0.146,0.083 0.302,0.26 0.156,0.177 10 false *a
*a Rear view of wire harness connector
(to Power Management Control ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
I3-4 (SMRB) - Body ground Power switch off 25.0 to 59.0 Ω



c.

Connect the power management control ECU connector.

Result:
Proceed to
OK
NG




OK

7.CHECK HARNESS AND CONNECTOR (SHORT TO POWER SUPPLY WIRES)

NG

8.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - HYBRID BATTERY JUNCTION BLOCK ASSEMBLY)
7.CHECK HARNESS AND CONNECTOR (SHORT TO POWER SUPPLY WIRES)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
A258634C07
0.063,0.02 0.326,0.194 0.264,0.174 10 *1 1.532,0.641 0.721,1.012 false 0.504,0.96 0.694,1.133 0.19,0.174 10 *2
*1 No. 2 Engine Room Relay Block
*2 PM IGCT Fuse


Remove the PM IGCT fuse from the No. 2 engine room relay block.


c.
A256541C04
3.052,1.26 2.354,1.104 true 0.448,0.063 0.708,0.24 0.26,0.177 10 false *1 3.073,1.177 3.333,1.354 0.26,0.177 10 false *2
*1 Engine Room Relay Block and Junction Block Assembly
*2 AM2 Fuse


Remove the AM2 fuse from the engine room relay block and junction block assembly.


d.
A265460C04
1.938,1.76 2.583,1.948 true 0.208,0.146 0.458,0.365 0.25,0.219 10 false *1 2.615,1.885 2.833,2.063 0.219,0.177 10 false *2
*1 Instrument Panel Junction Block Assembly
*2 ECU-IG2 NO. 1 Fuse


Remove the ECU-IG2 NO. 1 fuse from the instrument panel junction block assembly.


e.

Remove the No. 4 hybrid battery shield panel.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV RELAY ASSEMBLY>REMOVAL


f.
A259726N02
1.583,0.625 2.073,0.917 0.49,0.292 1.708,0.688 1.906,0.865 0.198,0.177 10 true O9

Disconnect connector O9 from the hybrid battery junction block assembly.


g.

Disconnect all the connectors from the power management control ECU.


h.
A317806C27
0.406,1.448 0.719,1.656 0.313,0.208 1.198,1.448 1.51,1.656 0.313,0.208 1.99,1.458 2.302,1.667 0.313,0.208 2.74,1.458 3.052,1.667 0.313,0.208 0.885,2.698 0.76,2.104 false 0.198,2.76 0.563,2.115 false 1.26,2.708 1.375,2.125 false 1.656,2.75 1.583,2.125 false 1.938,3.083 1.917,2.188 false 2.177,2.698 2.125,2.115 false 2.49,3.063 2.333,2.115 false 2.74,2.688 2.708,2.104 false 3.177,2.698 3.115,2.125 false 2.885,3.073 3.052,2.115 false 0.51,3.01 0.719,2.25 false 1.427,3.052 1.51,2.135 false 2.99,2.729 3.417,2.99 0.427,0.26 10 false ACCD 0.073,0.115 0.385,0.271 0.313,0.156 10 false *a 0.448,1.479 0.76,1.635 0.313,0.156 10 false A38 1.24,1.479 1.552,1.635 0.313,0.156 10 false A39 2.104,1.49 2.417,1.646 0.313,0.156 10 false I3 2.854,1.49 3.167,1.646 0.313,0.156 10 false I4 2.771,3.115 3.198,3.375 0.427,0.26 10 false IG1D 2.563,2.729 2.99,2.99 0.427,0.26 10 false AM21 2.344,3.115 2.771,3.375 0.427,0.26 10 false AM22 2.031,2.729 2.458,2.99 0.427,0.26 10 false SMRB 1.792,3.115 2.219,3.375 0.427,0.26 10 false SPDI 1.594,2.792 2.021,3.052 0.427,0.26 10 false IG2 1.135,2.74 1.563,3 0.427,0.26 10 false +B1 0.021,2.792 0.448,3.052 0.427,0.26 10 false MREL 0.781,2.74 1.208,3 0.427,0.26 10 false +B2 0.427,3.042 0.688,3.24 0.26,0.198 10 false GI 1.302,3.083 1.729,3.344 0.427,0.26 10 false IG2D
*a Rear view of wire harness connector
(to Power Management Control ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
I3-4 (SMRB) - A38-1 (+B2) Power switch off 10 kΩ or higher
I3-4 (SMRB) - A39-3 (+B1) Power switch off 10 kΩ or higher
I3-4 (SMRB) - I3-1 (AM22) Power switch off 10 kΩ or higher
I3-4 (SMRB) - I4-7 (AM21) Power switch off 10 kΩ or higher
I3-4 (SMRB) - A38-4 (MREL) Power switch off 10 kΩ or higher
I3-4 (SMRB) - A39-1 (IG2) Power switch off 10 kΩ or higher
I3-4 (SMRB) - I4-1 (ACCD) Power switch off 10 kΩ or higher
I3-4 (SMRB) - I4-2 (IG1D) Power switch off 10 kΩ or higher
I3-4 (SMRB) - A39-2 (IG2D) Power switch off 10 kΩ or higher
I3-4 (SMRB) - I3-16 (SPDI) Power switch off 10 kΩ or higher
I3-4 (SMRB) - A38-19 (GI) Power switch off 10 kΩ or higher



i.

Connect the power management control ECU connectors.


j.

Connect the hybrid battery junction block assembly connector.


k.

Install the No. 4 hybrid battery shield panel.


l.

Install the PM IGCT fuse, AM2 fuse and ECU-IG2 NO. 1 fuse.

Result:
Proceed to
OK
NG




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - HYBRID BATTERY JUNCTION BLOCK ASSEMBLY)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 4 hybrid battery shield panel (Click here Engine / Hybrid System>HYBRID / BATTERY CONTROL>HV RELAY ASSEMBLY>REMOVAL).


c.

Disconnect connector O9 from the hybrid battery junction block assembly.


d.

Disconnect connector I3 from the power management control ECU.


e.
A284482C29
1.906,2.365 2.156,2.594 0.25,0.229 1.552,3.51 1.802,3.74 0.25,0.229 2.021,1.781 1.552,1.781 true 2.198,3.688 2.708,4.406 true 0.042,0.063 0.354,0.219 0.313,0.156 10 false *a 0.073,2.531 0.385,2.688 0.313,0.156 10 false *b 1.135,1.708 1.75,1.906 0.615,0.198 10 false SMRB 2.771,4.344 3.219,4.552 0.448,0.208 10 false SMRB 1.99,2.406 2.302,2.604 0.313,0.198 10 false I3 1.604,3.563 1.917,3.76 0.313,0.198 10 false O9
*a Rear view of wire harness connector
(to Power Management Control ECU)
*b Rear view of wire harness connector
(to Hybrid Battery Junction Block Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Switch Condition Specified Condition
I3-4 (SMRB) - O9-1 (SMRB) Power switch off Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Switch Condition Specified Condition
I3-4 (SMRB) and O9-1 (SMRB) - Body ground and other terminals Power switch off 10 kΩ or higher



f.

Connect the power management control ECU connector.


g.

Connect the hybrid battery junction block assembly connector.


h.

Install the No. 4 hybrid battery shield panel.

Result:
Proceed to
OK
NG




OK

9.CHECK HARNESS AND CONNECTOR (HYBRID BATTERY JUNCTION BLOCK ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HARNESS AND CONNECTOR (HYBRID BATTERY JUNCTION BLOCK ASSEMBLY - BODY GROUND)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 4 hybrid battery shield panel (Click here Engine / Hybrid System>HYBRID / BATTERY CONTROL>HV RELAY ASSEMBLY>REMOVAL).


c.

Disconnect connector O9 from the hybrid battery junction block assembly.


d.
A259727C07
1.344,1 1.833,1.292 0.49,0.292 2.156,1.198 2.573,1.885 true 0.042,0.031 0.24,0.188 0.198,0.156 10 false *a 2.667,1.844 3.021,2 0.354,0.156 10 false GND 1.469,1.052 1.667,1.229 0.198,0.177 10 false O9
*a Rear view of wire harness connector
(to Hybrid Battery Junction Block Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
O9-2 (GND) - Body ground Power switch off Below 1 Ω



e.

Connect the hybrid battery junction block assembly connector.


f.

Install the No. 4 hybrid battery shield panel.

Result:
Proceed to
OK
NG




OK

10.CHECK HV BATTERY JUNCTION BLOCK ASSEMBLY (SMRB)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK HV BATTERY JUNCTION BLOCK ASSEMBLY (SMRB)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the hybrid battery junction block assembly (Click here Engine / Hybrid System>HYBRID / BATTERY CONTROL>HV RELAY ASSEMBLY>COMPONENTS).


c.
A259731C31
0.24,2.344 0.656,2.583 0.417,0.24 1.406,2.521 1.594,2.76 true 1.198,2.531 0.865,2.771 true 0.344,2.375 0.625,2.542 0.281,0.167 10 false O9 0.646,2.792 0.99,2.958 0.344,0.167 10 false GND 1.385,2.792 1.813,2.958 0.427,0.167 10 false SMRB 0.052,0.083 0.396,0.25 0.344,0.167 10 false *a
*a Component without harness connected
(Hybrid Battery Junction Block Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
O9-1 (SMRB) - O9-2 (GND) -40 to 80 °C (-40 to 176°F) 25.0 to 59.0 Ω



d.

Install the hybrid battery junction block assembly.


Result:
Proceed to
OK
NG



OK

NG

REPLACE HV BATTERY JUNCTION BLOCK ASSEMBLY