The inverter water pump assembly transmits rotation revolution speed information to the power management control ECU. The power management control ECU monitors the revolution speed and detects malfunctions.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Warning Indicate |
|---|---|---|---|---|---|
| P0C73-776 | Motor Electronics Coolant Pump "A" Control Performance | A speed or intermittent stop malfunction occurs in the inverter water pump assembly.
A revolution malfunction (speed is too high/low or stop) or an intermittent stop malfunction (operation stops intermittently when the speed revolution is abnormal) occurs in the inverter water pump assembly. |
·
Inverter cooling system ·
Wire harness or connector ·
Inverter water pump assembly ·
Power management control ECU |
Comes on | Master Warning Light:
Comes on |
The inverter water pump assembly operates when the power switch is on (READY).
| DTC No. | Active Test |
|---|---|
| P0C73-776 | Activate the Water Pump*1 |
*1: This is an Active Test of the inverter water pump assembly.
If DTC P0A78-284, 286, P0A7A-322, 324, P0A94-553 or 557 is output, replace the inverter with converter assembly after this inspection.
After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.
Turn the power switch on (READY) and wait for 120 seconds or more (when the power switch is turned on (READY), the inverter water pump assembly operates).
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0A01-726
| Proceed to |
|---|
| A |
| B |
| C |
A
B
C
In the case of a coolant leak, the inverter water pump assembly activates a fail-safe function. If the inverter water pump assembly is not the cause of the coolant leak, it is not necessary to replace it.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0A01-726
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Be sure to perform the inspection with the auxiliary battery voltage at 11 V or more.
When the auxiliary battery voltage is low, the inverter water pump assembly may not operate.
When the inverter water pump assembly serial communication line (SWP - IWP) is open or its connection is faulty, the inverter water pump assembly is operated forcibly.
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Data List / Inverter W/P Revolution.
| Tester Display |
|---|
| Inverter W/P Revolution |
Read the Data List.
| Tester Display | Condition | Specified Condition |
|---|---|---|
| Inverter W/P Revolution | Power switch on (IG) | 625 rpm or less |
When the inverter water pump assembly is not operating, the Data List item "Inverter W/P Revolution" usually displays 625 rpm continuously.
Turn the power switch off.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0A09-265
| Proceed to |
|---|
| NEXT |
NEXT
Be sure to perform the inspection with the auxiliary battery voltage at 11 V or more.
When the auxiliary battery voltage is low, the inverter water pump assembly may not operate.
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Active Test / Activate the Water Pump.
| Tester Display |
|---|
| Activate the Water Pump |
Select Inverter W/P Revolution in the Data List.
While performing the "Activate the Water Pump" Active Test, check Inverter W/P Revolution in the Data List.
| Tester Display |
|---|
| Inverter W/P Revolution |
| Data List Item | Specified Condition |
|---|---|
| Inverter W/P Revolution | 2500 to 5875 rpm |
Perform the Active Test with the inverter coolant temperature between -15 and 65°C (5 to 149°F).
When the inverter water pump assembly is not operating, the Data List item "Inverter W/P Revolution" usually displays 625 rpm continuously.
Turn the power switch off.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0A08-264
| Proceed to |
|---|
| A |
| B |
A
B
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0340-886
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the connector connections and contact pressure of the relevant terminals for the inverter water pump assembly connector.
The connectors are connected securely and there are no contact pressure problems.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect connector A38 from the power management control ECU.
Disconnect connector A50 from the inverter water pump assembly.
Measure the resistance according to the value(s) in the table below.
| *a | Rear view of wire harness connector
(to Power Management Control ECU) |
*b | Front view of wire harness connector
(to Inverter Water Pump Assembly) |
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| A50-3 (SWP) - A38-13 (IWP) | Power switch off | Below 1 Ω |
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| A50-3 (SWP) or A38-13 (IWP) - Body ground and other terminals | Power switch off | 10 kΩ or higher |
Connect the power management control ECU connector.
Connect the inverter water pump assembly connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Be sure to perform the inspection with the auxiliary battery voltage at 11 V or more.
When the auxiliary battery voltage is low, the inverter water pump assembly may not operate.
Connect the intelligent tester to the DLC3.
Remove the INV W/PMP fuse from the No. 2 engine room relay block.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / ECU Data List / Inverter W/P Revolution.
| Tester Display |
|---|
| Inverter W/P Revolution |
Read the Data List.
| Tester Display | Condition | Specified Condition |
|---|---|---|
| Inverter W/P Revolution | Power switch on (IG) | 125 rpm or less |
Turn the power switch off.
Install the INV W/PMP fuse.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect connector A38 from the power management control ECU.
Turn the power switch on (IG).
| *a | Rear view of wire harness connector
(to Power Management Control ECU) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A38-13 (IWP) - I3-6 (E1) | Power switch on (IG) | 11 to 14 V |
Turning the power switch on (IG) with the power management control ECU connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.
Turn the power switch off.
Connect the power management control ECU connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the power switch on (IG).
| *a | Component with harness connected
(Power Management Control ECU) |
While turning the power switch on (IG), check the waveform between the power management control ECU terminals.
| Item | Content |
|---|---|
| Terminal | A38-13 (IWP) - I3-6 (E1) |
| Equipment Setting | 5 V/DIV., 50 ms./DIV. |
| Condition | Power switch on (IG) |
Waveform duty ratio is between 3% and 9%.
Turn the power switch off.
| Proceed to |
|---|
| OK |
| NG |
OK
NG