Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › from 2015.04
RM2040EQ _51 Engine / Hybrid System _014692 HYBRID / BATTERY CONTROL _0074885 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P314A-828  Inverter Coolant Pump Speed Signal  


DESCRIPTION

Refer to the description for DTC P0C73-776 (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0C73-776).

If the water pump speed (measured value) signal is not sent to the power management control ECU when the power switch is on (READY), this DTC is stored.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P314A-828 Inverter Coolant Pump Speed Signal When either of the following conditions is met:
·

A malfunction in the power source circuit or water pump speed signal line of the inverter water pump assembly is detected.

·

A malfuncution in the power source circuit of the inverter water pump assembly or power management control ECU is detected.


·

Wire harness or connector

·

Power management control ECU

·

Inverter water pump assembly

·

INV W/PMP fuse

·

INV W/PMP RLY fuse

·

INV W/PMP relay


Comes on Master Warning Light:
Comes on

Related Active Test
DTC No. Active Test
P314A-828 Activate the Water Pump*1

*1: This is an Active Test of the inverter water pump assembly.

WIRING DIAGRAM

Refer to the wiring diagram for DTC P0C73-776 (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0C73-776).

CAUTION / NOTICE / HINT

NOTICE:

If DTC P0A78-284, 286, P0A7A-322, 324, P0A94-553 or 557 is output, replace the inverter with converter assembly after this inspection.


HINT:

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

1.

Turn the power switch on (READY) and wait for 2 minutes or more.



PROCEDURE

1.CLEAR DTC

NEXT

2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (ACTIVATE THE WATER PUMP)
2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (ACTIVATE THE WATER PUMP)
NOTICE:

Be sure to perform the inspection with the auxiliary battery voltage at 11 V or more.


HINT:

When the auxiliary battery voltage is low, the inverter water pump assembly may not operate.


a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Active Test / Activate the Water Pump.

Powertrain > Hybrid Control > Active Test
Tester Display
Activate the Water Pump
50004 236 9

d.

Perform the Activate the Water Pump Active Test.


e.

Touch the inverter water pump assembly and check that it is operating (vibrating).

OK:

The inverter water pump is operating (vibrating).



f.

Turn the power switch off.

Result:
Proceed to
OK
NG




OK

3.CHECK CONNECTOR CONNECTION CONDITION (POWER MANAGEMENT CONTROL ECU CONNECTOR)

NG

9.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WATER PUMP ASSEMBLY CONNECTOR)
3.CHECK CONNECTOR CONNECTION CONDITION (POWER MANAGEMENT CONTROL ECU CONNECTOR)

OK

4.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WATER PUMP ASSEMBLY CONNECTOR)

NG

CONNECT SECURELY

4.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WATER PUMP ASSEMBLY CONNECTOR)

OK

5.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - INVERTER WATER PUMP ASSEMBLY)

NG

CONNECT SECURELY

5.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - INVERTER WATER PUMP ASSEMBLY)
a.

Disconnect connector A38 from the power management control ECU.


b.

Disconnect connector A50 from the inverter water pump assembly.


c.

Measure the resistance according to the value(s) in the table below.

A265405C31
0.406,1.719 0.781,1.948 0.375,0.229 4.375,1.292 4.75,1.521 0.375,0.229 0.917,2.24 1.156,1.823 false 5.031,1.875 5.302,1.469 false 0.49,1.771 0.792,1.938 0.302,0.167 10 false A38 0.74,2.26 1.115,2.458 0.375,0.198 10 false NIWP 0.323,0.354 0.573,0.542 0.25,0.188 10 false *a 4.573,0.813 4.75,0.979 0.177,0.167 10 false *b 4.448,1.344 4.771,1.552 0.323,0.208 10 false A50 4.906,1.896 5.26,2.115 0.354,0.219 10 false NWP
*a Rear view of wire harness connector
(to Power Management Control ECU)
*b Front view of wire harness connector
(to Inverter Water Pump Assembly)


Standard Resistance:
Tester Connection Switch Condition Specified Condition
A38-12 (NIWP) - A50-2 (NWP) Power switch off Below 1 Ω
A38-12 (NIWP) or A50-2 (NWP) -Body ground and other terminals Power switch off 10 kΩ or higher



d.

Connect the power management control ECU connector.


e.

Connect the inverter water pump assembly connector.

Result:
Proceed to
OK
NG




OK

6.CHECK POWER MANAGEMENT CONTROL ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK POWER MANAGEMENT CONTROL ECU
a.

Disconnect connector A50 from the inverter water pump assembly.


b.

Turn the power switch on (IG).


c.
A249750C20
0.594,0.938 1.01,1.177 0.417,0.24 1.865,0.938 2.281,1.177 0.417,0.24 0.823,1.771 0.667,2.396 false 1.823,1.708 1.865,2.385 false 0.677,1 1.083,1.219 0.406,0.219 10 false A38 0.177,0.156 0.448,0.323 0.271,0.167 10 false *a 1.802,2.427 2.198,2.74 0.396,0.313 10 false E1 0.542,2.438 0.958,2.698 0.417,0.26 10 false NIWP 2.021,0.99 2.427,1.208 0.406,0.219 10 false I3
*a Component with harness connected
(Power Management Control ECU)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A38-12 (NIWP) - I3-6 (E1) Power switch on (IG) 11 to 14 V



d.

Turn the power switch off.


e.

Connect the inverter water pump assembly connector.

Result:
Proceed to
OK
NG




OK

7.CLEAR DTC

NG

7.CLEAR DTC

NEXT

8.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (ACTIVATE THE WATER PUMP)
8.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (ACTIVATE THE WATER PUMP)
NOTICE:

Be sure to perform the inspection with the auxiliary battery voltage at 11 V or more.


HINT:

When the auxiliary battery voltage is low, the inverter water pump assembly may not operate.


a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Active Test / Activate the Water Pump.

Powertrain > Hybrid Control > Active Test
Tester Display
Activate the Water Pump
50004 236 9

d.

Perform the "Activate the Water Pump" Active Test.


e.
C264839C15
0.729,0.458 1.031,0.667 0.302,0.208 1.792,0.448 2.094,0.656 0.302,0.208 0.771,1.656 0.906,1.146 true 1.969,1.646 1.771,1.083 true 0.083,0.063 0.396,0.219 0.313,0.156 10 false *a 0.771,0.49 1.083,0.646 0.313,0.156 10 false A38 1.896,0.479 2.208,0.635 0.313,0.156 10 false I3 1.927,1.677 2.24,1.833 0.313,0.156 10 false E1 0.573,1.677 1.115,1.896 0.542,0.219 10 false NIWP 2.688,3.719 3.229,3.938 0.542,0.219 10 false GND
*a Component with harness connected
(Power Management Control ECU)


Connect an oscilloscope between the power management control ECU terminals specified in the table below, and measure the waveform.

Item Content
Terminal A38-12 (NIWP) - I3-6 (E1)
Equipment Setting 5 V/DIV., 100 ms./DIV.
Condition Power switch on (IG), during Active Test

OK:

The duration of wavelength is 300 msec or less.



f.

Turn the power switch off.

Result:
Proceed to
OK
NG




OK

NG

9.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WATER PUMP ASSEMBLY CONNECTOR)

OK

10.CHECK INSTALLATION CONDITION (INV W/PMP RELAY)

NG

CONNECT SECURELY

10.CHECK INSTALLATION CONDITION (INV W/PMP RELAY)
a.
A308320C01
2.021,0.781 2.854,1.021 false 0.219,0.198 0.531,0.396 0.313,0.198 10 false *1 2.927,0.969 3.24,1.167 0.313,0.198 10 false *2
*1 No. 2 Engine Room Relay Block
*2 INV W/PMP Relay


Check installation condition of the INV W/PMP relay.

OK:

INV W/PMP relay is installed correctly.



Result:
Proceed to
OK
NG



OK

11.CHECK HARNESS AND CONNECTOR (IGCT RELAY - INV W/PMP RELAY)

NG

34.INSPECT RELAY (INV W/PMP)
11.CHECK HARNESS AND CONNECTOR (IGCT RELAY - INV W/PMP RELAY)
a.

Remove the IGCT relay and INV W/PMP relay from the No. 2 engine room relay block.


b.
A308321C01
0.26,0.229 0.542,0.427 0.281,0.198 10 false *1 2.406,0.781 2.688,0.979 0.281,0.198 10 false *2 2.458,1.729 2.74,1.927 0.281,0.198 10 false *3
*1 No. 2 Engine Room Relay Block
*2 INV W/PMP Relay
*3 IGCT Relay


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
5 (IGCT relay) - 1 (INV W/PMP relay) Power switch off Below 1 Ω


NOTICE:

Do not apply excessive force when using the probes of the tester to perform the inspection. If excessive force is used, the holders will be damaged.


HINT:
A288054C02
0.177,0.177 0.49,0.375 0.313,0.198 10 *a 0.99,1.385 1.302,1.583 0.313,0.198 10 *b 2.021,2.979 2.333,3.177 0.313,0.198 10 *c
*a Example
*b Shake Slightly
*c Vibrate Slightly


·

Connectors

Slightly shake the connector vertically and horizontally.

·

Wire Harness

Slightly shake the wire harness vertically and horizontally.

The connector joint and fulcrum of the vibration are the major areas that should be checked thoroughly.

·

No. 2 Engine Room Relay Block

Apply slight vibration with a finger to the No. 2 engine room relay block and check whether a malfunction occurs.

·

INV W/PMP RLY fuse

Apply slight vibration with a finger to the INV W/PMP RLY fuse and check whether a malfunction occurs.




c.

Install the IGCT relay and INV W/PMP relay.


Result:
Proceed to
OK
NG



OK

12.INSPECT RELAY (INV W/PMP)

NG

29.CHECK INSTALLATION CONDITION (INV W/PMP RLY FUSE)
12.INSPECT RELAY (INV W/PMP)
a.
A308320C01
2.021,0.781 2.854,1.021 false 0.219,0.198 0.531,0.396 0.313,0.198 10 false *1 2.927,0.969 3.24,1.167 0.313,0.198 10 false *2
*1 No. 2 Engine Room Relay Block
*2 INV W/PMP Relay


Remove the INV W/PMP relay from the No. 2 engine room relay block.


b.
A167865C03
2.615,0.552 2.708,0.198 2.708,0.198 2.792,0.198 true 2.031,0.563 1.938,0.198 1.938,0.198 1.854,0.198 true 2.531,1.125 2.948,1.125 true 2.531,1.625 2.948,1.625 true 0.094,0.083 0.406,0.24 0.313,0.156 10 *1 0.229,0.792 0.542,0.948 0.313,0.156 10 5 0.24,1.333 0.552,1.49 0.313,0.156 10 2 1.198,1.333 1.51,1.49 0.313,0.156 10 1 1.208,0.792 1.521,0.948 0.313,0.156 10 3 1.75,0.135 2.063,0.292 0.313,0.156 10 1 2.844,0.125 3.156,0.281 0.313,0.156 10 2 3,1.063 3.313,1.219 0.313,0.156 10 5 3,1.563 3.313,1.719 0.313,0.156 10 3
*1 INV W/PMP Relay


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Auxiliary battery voltage is not applied between terminals 1 and 2 10 kΩ or higher
Auxiliary battery voltage is applied between terminals 1 and 2 Below 1 Ω



c.

Install the INV W/PMP relay.


Result:
Proceed to
OK
NG



OK

13.CHECK HARNESS AND CONNECTOR (INVERTER WATER PUMP ASSEMBLY - BODY GROUND)

NG

23.CHECK RELAY HOLDER TERMINAL (INV W/PMP RELAY)
13.CHECK HARNESS AND CONNECTOR (INVERTER WATER PUMP ASSEMBLY - BODY GROUND)
a.

Disconnect the A50 inverter water pump assembly connector.


b.
A288050C16
1.49,1.063 1.906,1.302 0.417,0.24 2.354,2.51 2.021,1.927 false 0.083,0.104 0.396,0.26 0.313,0.156 10 false *a 2.198,2.563 2.656,2.76 0.458,0.198 10 false +BWP 1.594,1.104 2.01,1.281 0.417,0.177 10 false A50
*a Front view of wire harness connector
(to Inverter Water Pump Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A50-4 (+BWP) - Body ground Power switch on (IG) 11 to 14 V


NOTICE:

Turning the power switch on (IG) with the power management control ECU connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.


HINT:
A288054C02
0.177,0.177 0.49,0.375 0.313,0.198 10 *a 0.99,1.385 1.302,1.583 0.313,0.198 10 *b 2.021,2.979 2.333,3.177 0.313,0.198 10 *c
*a Example
*b Shake Slightly
*c Vibrate Slightly


·

Connectors

Slightly shake the connector vertically and horizontally.

·

Wire Harness

Slightly shake the wire harness vertically and horizontally.

The connector joint and fulcrum of the vibration are the major areas that should be checked thoroughly.

·

No. 2 Engine Room Relay Block

Apply slight vibration with a finger to the No. 2 engine room relay block and check whether a malfunction occurs.

·

INV W/PMP fuse

Apply slight vibration with a finger to the INV W/PMP fuse and check whether a malfunction occurs.

·

INV W/PMP relay

Apply slight vibration with a finger to the INV W/PMP relay and check whether a malfunction occurs.




c.

Connect the inverter water pump assembly connector.


Result:
Proceed to
OK
NG



OK

14.CHECK HARNESS AND CONNECTOR (INVERTER WATER PUMP ASSEMBLY - BODY GROUND)

NG

15.CHECK INSTALLATION CONDITION (INV W/PMP FUSE)
14.CHECK HARNESS AND CONNECTOR (INVERTER WATER PUMP ASSEMBLY - BODY GROUND)
a.

Disconnect the A50 inverter water pump assembly connector.


b.
A288050C17
1.49,1.063 1.906,1.302 0.417,0.24 1.125,2.448 1.365,1.896 false 0.083,0.104 0.396,0.26 0.313,0.156 10 false *a 0.99,2.5 1.448,2.698 0.458,0.198 10 false GND 1.594,1.104 1.917,1.271 0.323,0.167 10 false A50
*a Front view of wire harness connector
(to Inverter Water Pump Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A50-1 (GND) - Body ground Power switch off Below 1 Ω



c.

Connect the inverter water pump assembly connector.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

15.CHECK INSTALLATION CONDITION (INV W/PMP FUSE)
a.
A260031C04
2.229,1.323 2.865,1.594 false 0.167,0.125 0.448,0.313 0.281,0.188 10 false *1 2.896,1.521 3.167,1.698 0.271,0.177 10 false *2
*1 No. 2 Engine Room Relay Block
*2 INV W/PMP Fuse


Check installation condition of the INV W/PMP fuse.

OK:

INV W/PMP fuse is installed correctly.



Result:
Proceed to
OK
NG



OK

16.INSPECT RELAY (INV W/PMP)

NG

CONNECT SECURELY

16.INSPECT RELAY (INV W/PMP)
a.
A308320C01
2.021,0.781 2.854,1.021 false 0.219,0.198 0.531,0.396 0.313,0.198 10 false *1 2.927,0.969 3.24,1.167 0.313,0.198 10 false *2
*1 No. 2 Engine Room Relay Block
*2 INV W/PMP Relay


Remove the INV W/PMP relay from the No. 2 engine room relay block.


b.
A167865C03
2.615,0.552 2.708,0.198 2.708,0.198 2.792,0.198 true 2.031,0.563 1.938,0.198 1.938,0.198 1.854,0.198 true 2.531,1.125 2.948,1.125 true 2.531,1.625 2.948,1.625 true 0.094,0.083 0.406,0.24 0.313,0.156 10 *1 0.229,0.792 0.542,0.948 0.313,0.156 10 5 0.24,1.333 0.552,1.49 0.313,0.156 10 2 1.198,1.333 1.51,1.49 0.313,0.156 10 1 1.208,0.792 1.521,0.948 0.313,0.156 10 3 1.75,0.135 2.063,0.292 0.313,0.156 10 1 2.844,0.125 3.156,0.281 0.313,0.156 10 2 3,1.063 3.313,1.219 0.313,0.156 10 5 3,1.563 3.313,1.719 0.313,0.156 10 3
*1 INV W/PMP Relay


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Auxiliary battery voltage is not applied between terminals 1 and 2 10 kΩ or higher
Auxiliary battery voltage is applied between terminals 1 and 2 Below 1 Ω



c.

Install the INV W/PMP relay.


Result:
Proceed to
OK
NG



OK

17.CHECK HARNESS AND CONNECTOR (INVERTER WATER PUMP ASSEMBLY - NO. 2 ENGINE ROOM RELAY BLOCK)

NG

20.CHECK RELAY HOLDER TERMINAL (INV W/PMP RELAY)
17.CHECK HARNESS AND CONNECTOR (INVERTER WATER PUMP ASSEMBLY - NO. 2 ENGINE ROOM RELAY BLOCK)
a.

Remove the INV W/PMP relay from the No. 2 engine room relay block.


b.

Disconnect the A50 inverter water pump assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

A260034C03
0.875,1.292 1.25,1.521 0.375,0.229 2.365,1.854 2.094,1.49 false 1.031,0.698 1.198,0.854 0.167,0.156 10 false *a 3.823,0.417 3.99,0.573 0.167,0.156 10 false *1 5.667,0.75 5.833,0.906 0.167,0.156 10 false *2 0.948,1.323 1.292,1.698 0.344,0.375 10 false A50 2.271,1.865 2.792,2.073 0.521,0.208 10 false +BWP
*1 No. 2 Engine Room Relay Block *2 INV W/PMP Relay
*a Front view of wire harness connector
(to Inverter Water Pump Assembly)
- -


Standard Resistance:
Tester Connection Condition Specified Condition
A50-4 (+BWP) - 3 (INV W/PMP relay) Power switch off Below 1 Ω
A50-4 (+BWP) or 3 (INV W/PMP relay) - Body ground and other terminals Power switch off 10 kΩ or higher


NOTICE:

Do not apply excessive force when using the probes of the tester to perform the inspection. If excessive force is used, the holders will be damaged.



d.

Install the INV W/PMP relay.


e.

Connect the inverter water pump assembly connector.


Result:
Proceed to
OK
NG



OK

18.CHECK FUSE (INV W/PMP)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

18.CHECK FUSE (INV W/PMP)
a.
A260031C04
2.229,1.323 2.865,1.594 false 0.167,0.125 0.448,0.313 0.281,0.188 10 false *1 2.896,1.521 3.167,1.698 0.271,0.177 10 false *2
*1 No. 2 Engine Room Relay Block
*2 INV W/PMP Fuse


Remove the INV W/PMP fuse from the No. 2 engine room relay block.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
INV W/PMP fuse Always Below 1 Ω



c.

Install the INV W/PMP fuse.


Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (INV W/PMP FUSE HOLDER TERMINAL OR INV W/PMP RELAY HOLDER TERMINAL)

NG

19.REPLACE INVERTER WATER PUMP ASSEMBLY
19.REPLACE INVERTER WATER PUMP ASSEMBLY

NEXT

REPLACE FUSE (INV W/PMP)

20.CHECK RELAY HOLDER TERMINAL (INV W/PMP RELAY)
a.

Check the terminals of the INV W/PMP relay holder.

OK:

The terminals of the INV W/PMP relay holder are not bent, loose or corroded.



Result:
Proceed to
OK
NG



OK

21.CHECK FUSE (INV W/PMP RLY)

NG

24.CHECK FUSE (INV W/PMP RLY)
21.CHECK FUSE (INV W/PMP RLY)
a.
A260032C04
0.131,0.086 0.315,0.242 0.184,0.156 10 *1 2.786,1.547 2.97,1.703 0.184,0.156 10 *2 1.721,1.543 2.752,1.624 false
*1 No. 2 Engine Room Relay Block
*2 INV W/PMP RLY Fuse


Remove the INV W/PMP RLY fuse from the No. 2 engine room relay block.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
INV W/PMP RLY fuse Always Below 1 Ω



c.

Install the INV W/PMP RLY fuse.


Result:
Proceed to
OK
NG



OK

REPLACE RELAY (INV W/PMP)

NG

22.REPLACE RELAY (INV W/PMP)
22.REPLACE RELAY (INV W/PMP)
Result:
Proceed to
NEXT



NEXT

REPLACE FUSE (INV W/PMP RLY)

23.CHECK RELAY HOLDER TERMINAL (INV W/PMP RELAY)
a.

Check the terminals of the INV W/PMP relay holder.

OK:

The terminals of the INV W/PMP relay holder are not bent, loose or corroded.



Result:
Proceed to
OK
NG



OK

REPLACE RELAY (INV W/PMP)

NG

26.REPAIR OR REPLACE HARNESS OR CONNECTOR (INV W/PMP RELAY HOLDER TERMINAL)
24.CHECK FUSE (INV W/PMP RLY)
a.
A260032C04
0.131,0.086 0.315,0.242 0.184,0.156 10 *1 2.786,1.547 2.97,1.703 0.184,0.156 10 *2 1.721,1.543 2.752,1.624 false
*1 No. 2 Engine Room Relay Block
*2 INV W/PMP RLY Fuse


Remove the INV W/PMP RLY fuse from the No. 2 engine room relay block.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
INV W/PMP RLY fuse Always Below 1 Ω



c.

Install the INV W/PMP RLY fuse.


Result:
Proceed to
OK
NG



OK

25.REPAIR OR REPLACE HARNESS OR CONNECTOR (INV W/PMP RELAY HOLDER TERMINAL)

NG

27.REPAIR OR REPLACE HARNESS OR CONNECTOR (INV W/PMP RELAY HOLDER TERMINAL)
25.REPAIR OR REPLACE HARNESS OR CONNECTOR (INV W/PMP RELAY HOLDER TERMINAL)
Result:
Proceed to
NEXT



NEXT

REPLACE RELAY (INV W/PMP)

26.REPAIR OR REPLACE HARNESS OR CONNECTOR (INV W/PMP RELAY HOLDER TERMINAL)
Result:
Proceed to
NEXT



NEXT

REPLACE RELAY (INV W/PMP)

27.REPAIR OR REPLACE HARNESS OR CONNECTOR (INV W/PMP RELAY HOLDER TERMINAL)
Result:
Proceed to
NEXT



NEXT

28.REPLACE FUSE (INV W/PMP RLY)
28.REPLACE FUSE (INV W/PMP RLY)
Result:
Proceed to
NEXT



NEXT

REPLACE RELAY (INV W/PMP)

29.CHECK INSTALLATION CONDITION (INV W/PMP RLY FUSE)
a.
A260032C04
0.131,0.086 0.315,0.242 0.184,0.156 10 *1 2.786,1.547 2.97,1.703 0.184,0.156 10 *2 1.721,1.543 2.752,1.624 false
*1 No. 2 Engine Room Relay Block
*2 INV W/PMP RLY Fuse


Check installation condition of the INV W/PMP RLY fuse.

OK:

INV W/PMP RLY fuse is installed correctly.



Result:
Proceed to
OK
NG



OK

30.CHECK FUSE (INV W/PMP RLY)

NG

33.INSPECT RELAY (INV W/PMP)
30.CHECK FUSE (INV W/PMP RLY)
a.
A260032C04
0.131,0.086 0.315,0.242 0.184,0.156 10 *1 2.786,1.547 2.97,1.703 0.184,0.156 10 *2 1.721,1.543 2.752,1.624 false
*1 No. 2 Engine Room Relay Block
*2 INV W/PMP RLY Fuse


Remove the INV W/PMP RLY fuse from the No. 2 engine room relay block.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
INV W/PMP RLY fuse Always Below 1 Ω



c.

Install the INV W/PMP RLY fuse.


Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (INV W/PMP RLY FUSE HOLDER TERMINAL)

NG

31.CHECK FUSE HOLDER TERMINAL (INV W/PMP RLY FUSE)
31.CHECK FUSE HOLDER TERMINAL (INV W/PMP RLY FUSE)
a.

Check the terminals of the INV W/PMP RLY fuse holder.

OK:

The terminals of the INV W/PMP RLY fuse holder are not bent, loose or corroded.



Result:
Proceed to
OK
NG



OK

REPLACE FUSE (INV W/PMP RLY)

NG

32.REPAIR OR REPLACE HARNESS OR CONNECTOR (INV W/PMP RLY FUSE HOLDER TERMINAL)
32.REPAIR OR REPLACE HARNESS OR CONNECTOR (INV W/PMP RLY FUSE HOLDER TERMINAL)
Result:
Proceed to
NEXT



NEXT

REPLACE FUSE (INV W/PMP RLY)

33.INSPECT RELAY (INV W/PMP)
a.
A308320C01
2.021,0.781 2.854,1.021 false 0.219,0.198 0.531,0.396 0.313,0.198 10 false *1 2.927,0.969 3.24,1.167 0.313,0.198 10 false *2
*1 No. 2 Engine Room Relay Block
*2 INV W/PMP Relay


Remove the INV W/PMP relay from the No. 2 engine room relay block.


b.
A167865C03
2.615,0.552 2.708,0.198 2.708,0.198 2.792,0.198 true 2.031,0.563 1.938,0.198 1.938,0.198 1.854,0.198 true 2.531,1.125 2.948,1.125 true 2.531,1.625 2.948,1.625 true 0.094,0.083 0.406,0.24 0.313,0.156 10 *1 0.229,0.792 0.542,0.948 0.313,0.156 10 5 0.24,1.333 0.552,1.49 0.313,0.156 10 2 1.198,1.333 1.51,1.49 0.313,0.156 10 1 1.208,0.792 1.521,0.948 0.313,0.156 10 3 1.75,0.135 2.063,0.292 0.313,0.156 10 1 2.844,0.125 3.156,0.281 0.313,0.156 10 2 3,1.063 3.313,1.219 0.313,0.156 10 5 3,1.563 3.313,1.719 0.313,0.156 10 3
*1 INV W/PMP Relay


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Auxiliary battery voltage is not applied between terminals 1 and 2 10 kΩ or higher
Auxiliary battery voltage is applied between terminals 1 and 2 Below 1 Ω



c.

Install the INV W/PMP relay.


Result:
Proceed to
OK
NG



OK

CONNECT SECURELY (INV W/PMP RLY FUSE)

NG

35.REPLACE RELAY (INV W/PMP)
34.INSPECT RELAY (INV W/PMP)
a.
A308320C01
2.021,0.781 2.854,1.021 false 0.219,0.198 0.531,0.396 0.313,0.198 10 false *1 2.927,0.969 3.24,1.167 0.313,0.198 10 false *2
*1 No. 2 Engine Room Relay Block
*2 INV W/PMP Relay


Remove the INV W/PMP relay from the No. 2 engine room relay block.


b.
A167865C03
2.615,0.552 2.708,0.198 2.708,0.198 2.792,0.198 true 2.031,0.563 1.938,0.198 1.938,0.198 1.854,0.198 true 2.531,1.125 2.948,1.125 true 2.531,1.625 2.948,1.625 true 0.094,0.083 0.406,0.24 0.313,0.156 10 *1 0.229,0.792 0.542,0.948 0.313,0.156 10 5 0.24,1.333 0.552,1.49 0.313,0.156 10 2 1.198,1.333 1.51,1.49 0.313,0.156 10 1 1.208,0.792 1.521,0.948 0.313,0.156 10 3 1.75,0.135 2.063,0.292 0.313,0.156 10 1 2.844,0.125 3.156,0.281 0.313,0.156 10 2 3,1.063 3.313,1.219 0.313,0.156 10 5 3,1.563 3.313,1.719 0.313,0.156 10 3
*1 INV W/PMP Relay


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Auxiliary battery voltage is not applied between terminals 1 and 2 10 kΩ or higher
Auxiliary battery voltage is applied between terminals 1 and 2 Below 1 Ω



c.

Install the INV W/PMP relay.


Result:
Proceed to
OK
NG



OK

CONNECT SECURELY (INV W/PMP RELAY)

NG

36.REPLACE RELAY (INV W/PMP)
35.REPLACE RELAY (INV W/PMP)
Result:
Proceed to
NEXT



NEXT

CONNECT SECURELY (INV W/PMP RLY FUSE)

36.REPLACE RELAY (INV W/PMP)
Result:
Proceed to
NEXT



NEXT

CONNECT SECURELY (INV W/PMP RELAY)