Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM › from 2015.04
RM2040EQ _56 Audio / Visual / Telematics _014718 PARK ASSIST / MONITORING _0075026 BLIND SPOT MONITOR SYSTEM C

PARK ASSIST / MONITORING  BLIND SPOT MONITOR SYSTEM  C1AB1  Short to +B in Outer Mirror Indicator(Slave)  


DESCRIPTION

This DTC is stored when the blind spot monitor sensor LH detects a +B short in the outer rear view mirror indicator LH.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1AB1 Short to +B in Outer Mirror Indicator(Slave)
Both of the following conditions are met:
·

Blind spot monitor main switch (warning canceling switch assembly) is on.


·

The blind spot monitor sensor is not sending voltage to the indicator but the indicator receives voltage above a specified level for a specified period of time.


·

Outer mirror LH

·

Outer rear view mirror assembly LH

·

Wire harness or connector

·

Blind spot monitor sensor LH

·

Outer mirror control ECU assembly LH



WIRING DIAGRAM

E314323E20
1.604,1.26 1.76,1.458 0.156,0.198 10 false 1 1.604,1.74 1.74,1.896 0.135,0.156 10 false 2 1.302,1.365 1.458,1.563 0.156,0.198 10 false + 1.313,1.823 1.469,2.021 0.156,0.198 10 false - 0.271,2.188 0.885,2.385 0.615,0.198 10 false IND2 0.271,2.365 2.563,2.563 2.292,0.198 10 false Outer Mirror LH 0.26,2.646 2.427,3.031 2.167,0.385 10 false (Outer Rear View Mirror Indicator LH) 2.885,1.354 3.344,1.552 0.458,0.198 10 false z16 2.917,1.615 3.156,1.823 0.24,0.208 10 false 12 2.885,1.833 3.344,2.031 0.458,0.198 10 false z16 5.76,1.208 6.219,1.406 0.458,0.198 10 false 4 4.563,1.146 4.823,1.354 0.26,0.208 10 false 10 2.958,1.156 3.115,1.354 0.156,0.198 10 false 7 4.521,1.354 4.979,1.552 0.458,0.198 10 false K12 4.094,1.833 4.552,2.031 0.458,0.198 10 false GND 4.615,1.635 5.073,1.833 0.458,0.198 10 false 7 5.969,1.354 6.427,1.552 0.458,0.198 10 false OMIL 5.906,3.542 7.094,3.938 1.188,0.396 10 false Blind Spot Monitor Sensor LH 4,1.365 4.458,1.563 0.458,0.198 10 false BDSL 0.177,3.448 2.521,3.698 2.344,0.25 10 false Outer Rear View Mirror Assembly LH 3.198,3.417 4.75,3.771 1.552,0.354 10 false Outer Mirror Control ECU Assembly LH 5.906,3.385 6.365,3.583 0.458,0.198 10 false T21 4.552,1.833 5.01,2.031 0.458,0.198 10 false K12 3.271,1.354 3.729,1.552 0.458,0.198 10 false BDIL 3.292,1.823 3.75,2.021 0.458,0.198 10 false HTR-


CAUTION / NOTICE / HINT

NOTICE:

When checking for DTCs, make sure that the blind spot monitor main switch (warning canceling switch assembly) is on.


PROCEDURE

1.CHECK DTC
a.

Clear the DTCs.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>DTC CHECK / CLEAR

Body Electrical > Blind Spot Monitor Slave > Clear DTCs
50002 314

b.

Recheck for DTCs and check if the same DTC is output again.

Body Electrical > Blind Spot Monitor Slave > Trouble Codes
50001 314
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

NG

2.INSPECT OUTER MIRROR LH (OUTER MIRROR REAR VIEW INDICATOR CIRCUIT)
2.INSPECT OUTER MIRROR LH (OUTER MIRROR REAR VIEW INDICATOR CIRCUIT)
a.

Disconnect the T21 blind spot monitor sensor LH connector.


b.
E233763C13
1.542,0.448 2.063,0.76 0.521,0.313 1.896,1.625 2.438,0.833 false 2.438,0.833 2.646,0.833 false 0.094,0.094 0.302,0.292 0.208,0.198 10 false *a 2.667,0.74 3.115,0.927 0.448,0.188 10 false OMIL 1.688,0.531 2.01,0.708 0.323,0.177 10 false T21
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor LH)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
T21-4 (OMIL) - Body ground Power switch on (IG) Below 1 V



Result:
Proceed to
OK
NG



OK

NG

3.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR INDICATOR CIRCUIT)
3.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR INDICATOR CIRCUIT)
a.

Disconnect the IND2 outer mirror LH connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
T21-4 (OMIL) - Body ground Power switch on (IG) Below 1 V



Result:
Proceed to
OK
NG



OK

NG

4.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR INDICATOR CIRCUIT)
4.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR INDICATOR CIRCUIT)
a.

Disconnect the z16 outer mirror control ECU assembly LH connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
T21-4 (OMIL) - Body ground Power switch on (IG) Below 1 V



Result:
Proceed to
OK
NG



OK

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY LH

NG

5.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR INDICATOR CIRCUIT)
5.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR INDICATOR CIRCUIT)
a.

Disconnect the K12 outer mirror control ECU assembly LH connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
T21-4 (OMIL) - Body ground Power switch on (IG) Below 1 V



Result:
Proceed to
OK
NG



OK

REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR