This DTC is stored when a malfunction occurs in the speakers.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B15C3 | Speaker Output Short | A short is detected in the speaker output circuit | ·
Harness or connector ·
Speaker ·
Radio and display receiver assembly |
Disconnect the I152 and I153 radio and display receiver assembly connectors.
Disconnect the I83 and I1 front No. 2 speaker assembly connectors.
Disconnect the O18 and O21 rear speaker assembly connectors.
Measure the resistance between the radio and display receiver assembly and body ground to check for a short circuit in the wire harness.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I152-1 (FR+) - Body ground | Always | 10 kΩ or higher |
| I152-5 (FR-) - Body ground | Always | 10 kΩ or higher |
| I152-2 (FL+) - Body ground | Always | 10 kΩ or higher |
| I152-6 (FL-) - Body ground | Always | 10 kΩ or higher |
| I153-1 (RR+) - Body ground | Always | 10 kΩ or higher |
| I153-3 (RR-) - Body ground | Always | 10 kΩ or higher |
| I153-2 (RL+) - Body ground | Always | 10 kΩ or higher |
| I153-6 (RL-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the J5 and K5 front No. 1 speaker assembly connectors.
Disconnect the I83 and I1 front No. 2 speaker assembly connectors.
Measure the resistance between each of the front No. 2 speaker assemblies and body ground to check for a short circuit in the wire harness.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I83-3 (+) - Body ground | Always | 10 kΩ or higher |
| I83-1 (-) - Body ground | Always | 10 kΩ or higher |
| I1-3 (+) - Body ground | Always | 10 kΩ or higher |
| I1-1 (-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the front No. 1 speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>REMOVAL
| *a | Component without harness connected
(Front No. 1 Speaker Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 - 2 | Always | 3.2 to 4.8 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the front No. 2 speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>REMOVAL
| *A | for RH |
| *B | for LH |
| *a | Component without harness connected
(Front No. 2 Speaker Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 4 (TWR+) - 2 (TWR-) | Always | 10 kΩ or higher |
| 3 (+) - 4 (TWR+) | Always | Below 1 Ω |
| 1 (-) - 2 (TWR-) | Always | Below 1 Ω |
| 4 (TWL+) - 2 (TWL-) | Always | 10 kΩ or higher |
| 3 (+) - 4 (TWL+) | Always | Below 1 Ω |
| 1 (-) - 2 (TWL-) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the front No. 2 speaker assembly with a new or known good one.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>REMOVAL
Clear the DTCs.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM>DTC CHECK / CLEAR
Recheck for DTCs and check that no DTCs are output.
No DTCs are output.
Connect all the connectors to the front No. 2 speaker assemblies that were disconnected.
When there is a possibility that either the right or left front No. 2 speaker assembly is defective, inspect by interchanging the right one with the left one.
Perform the above inspection on both the LH and RH side.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the rear speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR PACKAGE TRAY SPEAKER>REMOVAL
| *a | Component without harness connected
(Rear Speaker Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 - 2 | Always | 3.2 to 4.8 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG