Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART ENTRY AND START SYSTEM(for Start Function) › from 2015.04
RM2040EQ _58 Vehicle Interior _014723 THEFT DETERRENT / KEYLESS ENTRY _0075054 SMART ENTRY AND START SYSTEM(for Start Function) C

THEFT DETERRENT / KEYLESS ENTRY  SMART ENTRY AND START SYSTEM(for Start Function)  B2284  Brake Signal Malfunction  


DESCRIPTION

This DTC is stored when the brake signal sent via direct line and the brake signal sent via CAN communication do not match.

HINT:

When the cable is disconnected and reconnected to the negative (-) auxiliary battery terminal, the power source mode returns to the state it was in before the cable was disconnected.


DTC No. Detection Item DTC Detection Condition Trouble Area Note
B2284 Brake Signal Malfunction The brake signal sent via direct line and the brake signal sent via CAN communication (1-trip detection logic*) do not match.
·

AM2 fuse

·

STOP fuse

·

Brake control system

·

Power management control ECU

·

Wire harness or connector


DTC Output Confirmation Operation

Connect the cable to the negative (-) auxiliary battery terminal, release the brake pedal and wait 20 seconds or more. Then depress the brake pedal for 20 seconds or more.



*: Only detected while a malfunction is present and the power switch is on (IG)


Vehicle Condition and Fail-safe Function when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Function when Malfunction Detected
With the electrical key transmitter sub-assembly in the cabin, even if an hybrid control system start operation is performed, the hybrid control system does not start (the multi-information display message (smart warning light) is not displayed). However, the hybrid control system can be started by turning the power switch on (ACC) and then pressing and holding it.
·

If there is a malfunction when the direct line is on, the hybrid control system can be started by pressing the power switch with the brake pedal released.

·

If there is a malfunction when the direct line is off, the hybrid control system cannot be started by pressing the power switch with the brake pedal depressed.


-

WIRING DIAGRAM

B293338E09
3.021,3.125 4.302,3.542 1.281,0.417 10 false Power Management Control ECU 2.156,2.135 3.125,2.823 0.969,0.688 10 false CAN Communication Line 0.521,2.469 2.063,3.177 1.542,0.708 10 false Skid Control ECU (Brake Booster with Master Cylinder Assembly) 4.583,0.854 6.323,1.021 1.74,0.167 10 false Stop Light Switch Assembly 4.583,0.708 5.052,1.021 0.469,0.313 10 false A33 0.385,0.573 1.26,0.896 0.875,0.323 10 false from Auxiliary Battery 1.771,0.74 2.104,0.927 0.333,0.188 10 false AM2 3.229,0.583 3.667,0.729 0.438,0.146 10 false AM21 2.958,0.375 3.073,0.521 0.115,0.146 10 false 7 2.948,0.573 3.156,0.76 0.208,0.188 10 false I4 3.229,0.979 3.667,1.125 0.438,0.146 10 false AM22 2.958,0.781 3.073,0.927 0.115,0.146 10 false 1 2.948,0.969 3.219,1.156 0.271,0.188 10 false I3 3.833,1.49 4.271,1.635 0.438,0.146 10 false E01 4.281,1.292 4.396,1.438 0.115,0.146 10 false 5 4.271,1.479 4.542,1.667 0.271,0.188 10 false I3 5.938,0.469 6.115,0.615 0.177,0.146 10 false 2 4.292,1.698 4.406,1.844 0.115,0.146 10 false 5 4.271,1.865 4.542,2.052 0.271,0.188 10 false I4 3.906,2.365 4.344,2.51 0.438,0.146 10 false E1 4.281,2.156 4.396,2.302 0.115,0.146 10 false 6 4.271,2.344 4.542,2.531 0.271,0.188 10 false I3 3.833,2.75 4.271,2.896 0.438,0.146 10 false E12 4.281,2.552 4.396,2.698 0.115,0.146 10 false 4 4.26,2.729 4.531,2.917 0.271,0.188 10 false I4 3.813,0.573 4.146,0.719 0.333,0.146 10 false STP 4.24,0.385 4.573,0.594 0.333,0.208 10 false 10 4.271,0.563 4.604,0.75 0.333,0.188 10 false I4 5.052,1.281 5.927,1.615 0.875,0.333 10 false from Auxiliary Battery 6.323,1.438 6.781,1.583 0.458,0.146 10 false STOP 4.781,0.469 5,0.615 0.219,0.146 10 false 1 3.823,1.885 4.26,2.031 0.438,0.146 10 false E02

CAUTION / NOTICE / HINT

HINT:

Check the connector connection to the terminal to make sure that there is no abnormality such as a loose connection, deformation, etc.


NOTICE:
·

When using the intelligent tester with the power switch off, perform either of the following: 1) Turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the intelligent tester and vehicle begins, or 2) connect the intelligent tester to the vehicle, select the vehicle type under manual mode, and then enter the following menus:

for Power Source Control: Body / Power Source Control / DTC.

for Entry&Start: Body / Entry&Start / DTC.

·

The smart entry and start system (for Start Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the smart entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

·

Before replacing the power management control ECU, refer to the Service Bulletin.

·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.

·

After performing repairs, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.



HINT:
Related Data List and Active Test Items
DTC Data List Item Active Test Item
B2284
Power Source Control
·

Stop Light Switch1


ABS/VSC/TRAC
·

Stop Light SW


-


PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SWITCH ASSEMBLY)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Power Source Control / Data List.


e.

Read the Data List according to the display on the intelligent tester.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Stop Light Switch1 Stop light switch1 ON or OFF ON: Brake pedal depressed
OFF: Brake pedal released
·

Use this item to determine whether the stop light switch is malfunctioning.

·

The hybrid control system cannot be started when this item is OFF.

·

When this item is malfunctioning, the hybrid control system can be started by pressing and holding the power switch for a certain period of time.


Body Electrical > Power Source Control > Data List
Tester Display
Stop Light Switch1
50003 223 3
OK:

ON (brake pedal is depressed) and OFF (brake pedal is released) appear on the screen.



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE)
2.CHECK HARNESS AND CONNECTOR (POWER SOURCE)

OK

3.CHECK HARNESS AND CONNECTOR (GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR IN CIRCUIT CONNECTED TO POWER SOURCE

3.CHECK HARNESS AND CONNECTOR (GROUND)

OK

4.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - STOP LIGHT SWITCH ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - STOP LIGHT SWITCH ASSEMBLY)
a.

Disconnect the A33 connector from the stop light switch assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I4-10 (STP) - A33-1 Always Below 1 Ω
I4-10 (STP) or A33-1 - Body ground Always 10 kΩ or higher



c.

Reconnect the A33 stop light switch assembly connector.


d.

Disconnect the I4 connector from the power management control ECU.


e.
B288689C08
1.469,0.094 1.927,0.375 0.458,0.281 1.219,1.604 1.417,1.208 false 1.635,0.146 1.906,0.302 0.271,0.156 10 false I4 0.177,0.156 0.344,0.313 0.167,0.156 10 false *a 1.031,1.667 1.396,1.823 0.365,0.156 10 false STP
*a Front view of wire harness connector(to Power Management Control ECU)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
I4-10 (STP) - Body ground Brake pedal released 1 V or less
Brake pedal depressed 9 V or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR