The main body ECU (multiplex network body ECU) detects whether either the rear doors are open or closed based on the courtesy light switch condition and then sends the rear door status signal to the combination meter assembly. The combination meter assembly detects rear seat belt state. The rear seat belt warning light on the clock assembly illuminates or turns off in accordance with the rear door state, vehicle speed and rear seat belt state.
The seat belt warning system uses the CAN communication system. First, confirm that there is no malfunction in the CAN communication system. Refer to the How to Proceed with Troubleshooting procedure (See page Vehicle Interior>SEAT BELT>SEAT BELT WARNING SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body / Main Body / Data List.
Read the Data List according to the display on the intelligent tester.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| RR Door Courtesy SW | Rear door courtesy light switch signal | ON or OFF | ON: Rear door RH open
OFF: Rear door RH closed |
- |
| RL Door Courtesy SW | Rear door courtesy light switch signal | ON or OFF | ON: Rear door LH open
OFF: Rear door LH closed |
- |
| Tester Display |
|---|
| RR Door Courtesy SW |
| RL Door Courtesy SW |
ON or OFF appears on the tester screen according to the rear door condition.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Rear Seat Belt Warning Light (Clock Assembly) |
| *b | LH |
| *c | Center |
| *d | RH |
Check the rear seat belt warning function.
Click hereVehicle Interior>SEAT BELT>SEAT BELT WARNING SYSTEM>ON-VEHICLE INSPECTION
| Result | Proceed to |
|---|---|
| The rear seat belt warning lights operation is normal | A |
| The rear seat belt warning lights (all seat) operation is not normal | B |
| The rear seat belt warning light (RH) operation is not normal | C |
| The rear seat belt warning light (center) operation is not normal | D |
| The rear seat belt warning light (LH) operation is not normal | E |
A
B
C
D
E
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body / Combination Meter / Active Test.
Perform the Active Test according to the display on the intelligent tester.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Rear Seat Belt | Rear seat belt warning light | ON/OFF | - |
| Tester Display |
|---|
| Rear Seat Belt |
| Result | Proceed to |
|---|---|
| The rear seat belt warning light does not operate normally | A |
| The rear seat belt warning light operates normally | B |
A
B
Disconnect the I59 clock assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I59-8 (IG+) - Body ground | Power switch on (IG) | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the I59 clock assembly connector.
Disconnect the I17 combination meter assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I17-9 (RLMT) - Body ground | Always | 11 to 14 V |
| I17-10 (RCMT) - Body ground | Always | 11 to 14 V |
| I17-11 (RRMT) - Body ground | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body / Combination Meter / Data List.
Read the Data List according to the display on the intelligent tester.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| 2nd-Row Seatbelt Buckle (R) | Rear RH seat belt buckle switch signal | ON or OFF | OFF: Rear RH seat belt fastened
ON: Rear RH seat belt not fastened |
- |
| Tester Display |
|---|
| 2nd-Row Seatbelt Buckle (R) |
| Result | Proceed to |
|---|---|
| ON or OFF does not appear on the tester screen according to the rear seat belt condition | A |
| ON or OFF appears on the tester screen according to the rear seat belt condition | B |
A
B
Disconnect the I18 combination meter assembly connector.
Disconnect the O45 rear seat inner with center belt assembly RH (for RH) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I18-6 (RRSB) - O45-1 | Always | Below 1 Ω |
| I18-6 (RRSB) - Body ground | Always | 10 kΩ or higher |
| O45-2 - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body / Combination Meter / Active Test.
Perform the Active Test according to the display on the intelligent tester.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Rear Seat Belt | Rear seat belt warning light | ON/OFF | - |
| Tester Display |
|---|
| Rear Seat Belt |
| Result | Proceed to |
|---|---|
| The rear seat belt warning light does not operate normally | A |
| The rear seat belt warning light operates normally | B |
A
B
Disconnect the I17 combination meter assembly connector.
Disconnect the I59 clock assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I17-3 (RRMT) - I59-5 (RRID) | Always | Below 1 Ω |
| I17-3 (RRMT) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body / Combination Meter / Data List.
Read the Data List according to the display on the intelligent tester.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| 2nd-Row Seatbelt Buckle (C) | Rear center seat belt buckle switch signal | ON or OFF | OFF: Rear center seat belt fastened
ON: Rear center seat belt not fastened |
- |
| Tester Display |
|---|
| 2nd-Row Seatbelt Buckle (C) |
| Result | Proceed to |
|---|---|
| ON or OFF does not appear on the tester screen according to the rear seat belt condition | A |
| ON or OFF appears on the tester screen according to the rear seat belt condition | B |
A
B
Disconnect the I18 combination meter assembly connector.
Disconnect the O46 rear seat inner with center belt assembly RH (for center) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I18-5 (RCSB) - O46-1 | Always | Below 1 Ω |
| I18-5 (RCSB) - Body ground | Always | 10 kΩ or higher |
| O46-2 - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body / Combination Meter / Active Test.
Perform the Active Test according to the display on the intelligent tester.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Rear Seat Belt | Rear seat belt warning light | ON/OFF | - |
| Tester Display |
|---|
| Rear Seat Belt |
| Result | Proceed to |
|---|---|
| The rear seat belt warning light does not operate normally | A |
| The rear seat belt warning light operates normally | B |
A
B
Disconnect the I17 combination meter assembly connector.
Disconnect the I59 clock assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I17-2 (RCMT) - I59-6 (RCID) | Always | Below 1 Ω |
| I17-2 (RCMT) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body / Combination Meter / Data List.
Read the Data List according to the display on the intelligent tester.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| 2nd-Row Seatbelt Buckle (L) | Rear LH seat belt buckle switch signal | ON or OFF | OFF: Rear LH seat belt fastened
ON: Rear LH seat belt not fastened |
- |
| Tester Display |
|---|
| 2nd-Row Seatbelt Buckle (L) |
| Result | Proceed to |
|---|---|
| ON or OFF does not appear on the tester screen according to the rear seat belt condition | A |
| ON or OFF appears on the tester screen according to the rear seat belt condition | B |
A
B
Disconnect the I18 combination meter assembly connector.
Disconnect the N41 rear seat inner with center belt assembly LH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I18-10 (RLSB) - N41-1 | Always | Below 1 Ω |
| I18-10 (RLSB) - Body ground | Always | 10 kΩ or higher |
| N41-2 - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body / Combination Meter / Active Test.
Perform the Active Test according to the display on the intelligent tester.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Rear Seat Belt | Rear seat belt warning light | ON/OFF | - |
| Tester Display |
|---|
| Rear Seat Belt |
| Result | Proceed to |
|---|---|
| The rear seat belt warning light does not operate normally | A |
| The rear seat belt warning light operates normally | B |
A
B
Disconnect the I17 combination meter assembly connector.
Disconnect the I59 clock assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I17-6 (RLMT) - I59-7 (RLID) | Always | Below 1 Ω |
| I17-6 (RLMT) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG