Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › from 2016.05
RM2040EQ _51 Engine / Hybrid System _014692 HYBRID / BATTERY CONTROL _0074885 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P0A08-264  DC / DC Converter Status Circuit  


DESCRIPTION

The hybrid vehicle converter (DC/DC converter) converts the DC 244.8 V of the HV battery into DC 12 V in order to supply power to areas such as the vehicle's lighting, audio, and ECU systems. In addition, it charges the auxiliary battery. A transistor bridge circuit initially converts DC 244.8 V into alternating current, and a transformer lowers its voltage. Then, it is rectified and smoothed (into DC) and converted into DC 12 V. The hybrid vehicle converter controls the output voltage in order to keep a constant voltage at the terminals of the auxiliary battery.

The power management control ECU uses the NODD signal line to transmit a stop command to the hybrid vehicle converter and receive signals indicating the normal or abnormal condition of the 12 V charging system. If the vehicle is being driven with an inoperative hybrid vehicle converter, the voltage of the auxiliary battery will drop, which will prevent the continued operation of the vehicle. Therefore, the power management control ECU monitors the operation of the hybrid vehicle converter and alerts the driver if it detects a malfunction.

A217225E19
1,0.938 1.479,1.156 0.479,0.219 10 false DC/DC 0.885,2.24 1.531,2.448 0.646,0.208 10 false DC/DC-S 0.927,2.583 1.458,2.813 0.531,0.229 10 false MAIN 2.052,0.688 2.417,0.896 0.365,0.208 10 false AMD 1.021,3.083 1.573,3.521 0.552,0.438 10 false Auxiliary Battery 3.083,4.458 5.51,4.729 2.427,0.271 10 false Power Management Control ECU 1.979,3.469 4.094,3.76 2.115,0.292 10 false Inverter with Converter Assembly 2.26,2.438 3.917,2.719 1.656,0.281 10 false Hybrid Vehicle Converter 3.906,2.188 4.146,2.396 0.24,0.208 10 false S 4.115,2.188 4.573,2.396 0.458,0.208 10 false NODD 4.604,2.188 5.031,2.385 0.427,0.198 10 false VLO 5.396,2.198 5.802,2.417 0.406,0.219 10 false IGCT 6.396,2.438 7.135,2.875 0.74,0.438 10 false from IGCT Relay 5.292,0.313 6.052,0.552 0.76,0.24 10 false DC244.8V 4.99,2.198 5.323,2.396 0.333,0.198 10 false IDH 4.906,3.917 7.156,4.156 2.25,0.24 10 false Air Conditioning Amplifier Assembly

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P0A08-264 DC / DC Converter Status Circuit DC/DC converter malfunction or the auxiliary battery voltage drops to 11 V or less with the power switch on (READY)
The DC/DC converter is malfunctioning for 120 seconds and the inverter coolant water temperature is 70°C or lower.
(1 trip detection logic)
·

Wire harness or connector

·

Inverter cooling system

·

Hybrid vehicle transaxle assembly

·

Inverter with converter assembly

·

Fuse (DC/DC-S)

·

Fusible link block assembly (DC/DC)

·

No. 3 engine room wire

·

Power management control ECU


Does not come on Master Warning Light:
Comes on

WIRING DIAGRAM

A260107E09
2.302,6.969 4.469,7.375 2.167,0.406 10 false Power Management Control ECU 0.604,6.115 1.698,6.323 1.094,0.208 10 false Auxiliary Battery 5.76,6.969 7.115,7.646 1.354,0.677 10 false Inverter with Converter Assembly 2.563,4.146 3,4.323 0.438,0.177 10 false IGCT 1.385,3.552 2.156,3.729 0.771,0.177 10 false IGCT-MAIN 2.51,1.677 3.01,1.854 0.5,0.177 10 false DC/DC 2.406,0.958 3.146,1.135 0.74,0.177 10 false DC/DC-S 0.531,5.177 1.198,5.354 0.667,0.177 10 false MAIN 3.948,5.135 4.417,5.313 0.469,0.177 10 false MREL 3.938,5.51 4.375,5.688 0.438,0.177 10 false NODD 4.167,6.448 4.417,6.625 0.25,0.177 10 false E1 6,5.5 6.5,5.677 0.5,0.177 10 false NODD 6.031,0.833 6.417,1.01 0.385,0.177 10 false S 6.01,1.531 6.396,1.708 0.385,0.177 10 false AMD 6.042,3.406 6.458,3.583 0.417,0.177 10 false IGCT 5.667,0.823 6.031,1 0.365,0.177 10 false A13 5.667,3.417 5.99,3.594 0.323,0.177 10 false A13 5.656,5.604 5.948,5.781 0.292,0.177 10 false A13 4.438,5.135 4.708,5.313 0.271,0.177 10 false A38 4.448,5.615 4.76,5.792 0.313,0.177 10 false A38 4.521,6.563 4.729,6.74 0.208,0.177 10 false I3 3.479,5.792 3.938,5.969 0.458,0.177 10 false 100 Ω 2.906,5.854 3.365,6.031 0.458,0.177 10 false 47 kΩ 2.896,6.333 3.354,6.51 0.458,0.177 10 false 82 kΩ 4.479,1.542 4.74,1.719 0.26,0.177 10 false 1K 3.865,3.313 4.063,3.49 0.198,0.177 10 false 2 3.333,3.313 3.531,3.49 0.198,0.177 10 false 1 2.281,3.781 2.479,3.958 0.198,0.177 10 false 2 3.052,3.771 3.25,3.948 0.198,0.177 10 false 1 3.063,3.313 3.26,3.49 0.198,0.177 10 false 5 2.281,3.313 2.479,3.49 0.198,0.177 10 false 3 1.99,3.313 2.188,3.49 0.198,0.177 10 false 2 1.458,3.313 1.656,3.49 0.198,0.177 10 false 1 2.948,0.719 3.146,0.896 0.198,0.177 10 false 2 2.396,0.719 2.594,0.896 0.198,0.177 10 false 1 4.531,6.375 4.74,6.583 0.208,0.208 10 false 6 4.49,5.417 4.802,5.594 0.313,0.177 10 false 23 4.531,4.938 4.646,5.115 0.115,0.177 10 false 4 5.74,5.406 6.01,5.583 0.271,0.177 10 false 5 5.74,0.635 5.938,0.813 0.198,0.177 10 false 3 5.729,3.208 5.833,3.385 0.104,0.177 10 false 1 4.521,1.333 4.615,1.51 0.094,0.177 10 false 1 1.031,2.333 4.563,2.677 3.531,0.344 10 false Engine Room Relay Block and Junction Block Assembly 1.75,4.5 3.771,4.844 2.021,0.344 10 false No.2 Engine Room Relay Block 5.698,1.542 5.958,1.719 0.26,0.177 10 false C1 5.74,1.344 5.833,1.521 0.094,0.177 10 false 1 3.229,3.563 4.167,3.74 0.938,0.177 10 false DC/DC IGCT 1.844,1.938 3.729,2.281 1.885,0.344 10 false Fusible Link Block Assembly

Refer to the wiring diagram for DTC P0AA6-526 (See page1Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0AA6-526).

CAUTION / NOTICE / HINT

CAUTION:
·

Before inspecting the high-voltage system or disconnecting the low voltage connector of the inverter with converter assembly, take safety precautions such as wearing insulated gloves and removing the service plug grip to prevent electrical shocks. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·

After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION).

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.




NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


HINT:
·

If the DC/DC converter is malfunctioning, the auxiliary battery cannot be charged. Therefore, once the power switch is turned off, it may be impossible to turn it on (READY) again if the auxiliary battery is completely discharged. In this case, charge the auxiliary battery. Be careful as charging is not performed during the inspection.


·

If the power switch turns off immediately after it is turned on (READY), the auxiliary battery voltage may be low. Charge the auxiliary battery.



PROCEDURE

1.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / DTC.

Powertrain > Hybrid Control > Trouble Codes
50001 236

d.

Check if DTCs are output.

Result:
Result Proceed to
P0A08-264 only is output. A
Any of the following DTCs are also output. B


Relevant DTC
P0A1B-547 Drive Motor "A" Control Module
P0A40-549 Drive Motor "A" Position Sensor Circuit Range / Performance
P0A78-548 Drive Motor "A" Inverter Performance
P0A93-346 Inverter Cooling System Performance
P0AA6-526, 613 Hybrid Battery Voltage System Isolation Fault
P0ADB-227 Hybrid Battery Positive Contactor Control Circuit Low
P0ADF-229 Hybrid Battery Negative Contactor Control Circuit Low
P0AE6-225 Hybrid Battery Precharge Contactor Control Circuit Low
P0C73-776 Motor Electronics Coolant Pump "A" Control Performance
P3004-131, 803 High Voltage Power Resource
P314A-828 Inverter Coolant Pump Speed Signal


e.

Turn the power switch off.



A

2.CHECK FUSE (DC/DC-S)

B

2.CHECK FUSE (DC/DC-S)
a.

Remove the DC/DC-S fuse from the engine room relay block and junction block assembly.


b.
A259800C05
2.177,1.406 2.74,1.469 true 0.156,0.125 0.354,0.313 0.198,0.188 10 false *1 2.76,1.385 2.958,1.573 0.198,0.188 10 false *2
*1 Engine Room Relay Block and Junction Block Assembly
*2 DC/DC-S Fuse


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
DC/DC-S fuse terminals Always Below 1 Ω



c.

Install the DC/DC-S fuse.

Result:
Proceed to
OK
NG




OK

3.CHECK CONNECTOR CONNECTION CONDITION (POWER MANAGEMENT CONTROL ECU CONNECTOR)

NG

17.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - DC/DC-S FUSE)
3.CHECK CONNECTOR CONNECTION CONDITION (POWER MANAGEMENT CONTROL ECU CONNECTOR)

OK

4.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WITH CONVERTER ASSEMBLY CONNECTOR)

NG

CONNECT SECURELY

4.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WITH CONVERTER ASSEMBLY CONNECTOR)

OK

5.CHECK FUSIBLE LINK BLOCK ASSEMBLY (DC/DC)

NG

CONNECT SECURELY

5.CHECK FUSIBLE LINK BLOCK ASSEMBLY (DC/DC)
a.
A258447C04
2.615,1.75 2.438,1.917 false 0.781,1.74 0.958,1.885 false 0.125,0.104 0.385,0.313 0.26,0.208 10 false *1 1,1.844 1.156,2 0.156,0.156 10 false 1 2.313,1.875 2.469,2.031 0.156,0.156 10 false 2
*1 Fusible Link Block Assembly


Check the fusible link block assembly (DC/DC) in the engine room relay block and junction block assembly for improper installation.

OK:

The fusible link is installed securely.



b.

Remove the fusible link block assembly from the engine room relay block and junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Fusible link block assembly (DC/DC) 1 - 2 Always Below 1 Ω



d.

Install the fusible link block assembly.

Result:
Proceed to
OK
NG




OK

6.CHECK CABLE AND WIRE HARNESS

NG

REPLACE FUSIBLE LINK BLOCK ASSEMBLY (DC/DC)

6.CHECK CABLE AND WIRE HARNESS
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
A258636

Remove the upper inverter cover (generator cable side) and upper inverter cover (motor cable side) from the inverter with converter assembly.


c.
A258637C10
0.583,1.281 0.948,1.521 0.365,0.24 1.302,1.76 1.667,2 0.365,0.24 2.01,0.521 2.323,0.365 true 1.021,0.396 0.729,0.521 true 0.698,0.948 0.865,1.115 0.167,0.167 10 false W 1,1.104 1.177,1.281 0.177,0.177 10 false V 1.229,1.229 1.417,1.417 0.188,0.188 10 false U 1.375,1.417 1.542,1.583 0.167,0.167 10 false W 1.646,1.573 1.823,1.75 0.177,0.177 10 false V 1.948,1.708 2.135,1.896 0.188,0.188 10 false U 2.333,0.281 2.573,0.469 0.24,0.188 10 true *1 0.563,0.458 0.75,0.646 0.188,0.188 10 true *2 0.677,1.323 0.885,1.49 0.208,0.167 10 false n1 1.406,1.802 1.615,1.969 0.208,0.167 10 false o1
*1 Generator Cable
*2 Motor Cable


Using a megohmmeter set to 500 V, measure the insulation resistance according to the value(s) in the table below.

NOTICE:

Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than 500 V can result in damage to the component being inspected.


Standard Resistance:
Tester Connection Switch Condition Specified Condition
o1-1 (W) - Body ground and shield ground Power switch off 1 MΩ or higher
o1-2 (V) - Body ground and shield ground Power switch off 1 MΩ or higher
o1-3 (U) - Body ground and shield ground Power switch off 1 MΩ or higher
n1-1 (W) - Body ground and shield ground Power switch off 1 MΩ or higher
n1-2 (V) - Body ground and shield ground Power switch off 1 MΩ or higher
n1-3 (U) - Body ground and shield ground Power switch off 1 MΩ or higher


HINT:

Perform this inspection while the generator cable and motor cable are connected.



d.

Install the upper inverter cover (generator cable side) and upper inverter cover (motor cable side).

Result:
Proceed to
OK
NG




OK

7.CHECK AMD TERMINAL VOLTAGE (ENGINE ROOM RELAY BLOCK AND JUNCTION BLOCK ASSEMBLY SIDE)

NG

19.CHECK HYBRID VEHICLE TRANSAXLE ASSEMBLY (MG1)
7.CHECK AMD TERMINAL VOLTAGE (ENGINE ROOM RELAY BLOCK AND JUNCTION BLOCK ASSEMBLY SIDE)
CAUTION:

Be sure to wear insulated gloves.


a.
A260097N02
1.823,0.042 2.188,0.281 0.365,0.24 1.917,0.083 2.125,0.25 0.208,0.167 10 false 1K

Connect the cable to the negative (-) auxiliary battery terminal.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
1K-1 (AMD) - Body ground Power switch off Same as auxiliary battery voltage



c.

Disconnect the cable from the negative (-) auxiliary battery terminal.

Result:
Proceed to
OK
NG




OK

8.CHECK AMD TERMINAL CONNECTION CONDITION

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK AMD TERMINAL CONNECTION CONDITION
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
A259381

Check that the bolt for the AMD terminal (inverter with converter assembly side and engine room relay block and junction block assembly side) is tightened to the specified torque, the AMD terminal (inverter with converter assembly side and engine room relay block and junction block assembly side) is connected securely, and there is no contact problem.

Torque:

T=18 N*m {184 kgf*cm, 13ft.*lbf } (Inverter with converter assembly side)

T=8.0 N*m {82 kgf*cm, 71in.*lbf } (Engine room relay block and junction block assembly side)



Result:
Result Proceed to
There are no arc marks. The terminal is connected securely and there is no contact problem. A
There are no arc marks. The terminal is not connected securely and there is a contact problem. B
There are arc marks. - C



A

9.CHECK NO. 3 ENGINE ROOM WIRE

B

CONNECT SECURELY

C

REPLACE MALFUNCTIONING PARTS

9.CHECK NO. 3 ENGINE ROOM WIRE
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect No. 3 engine room wire from the AMD terminal (inverter with converter assembly side and engine room relay block and junction block assembly side).


c.
A259734C03
0.479,0.708 0.844,0.948 0.365,0.24 2.385,0.229 2.75,0.469 0.365,0.24 0.583,0.75 0.792,0.917 0.208,0.167 10 false C1 2.49,0.271 2.698,0.438 0.208,0.167 10 false 1K 0.167,0.063 0.458,0.25 0.292,0.188 10 false *1
*1 No. 3 Engine Room Wire


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C1-1 (AMD) - 1K-1 (AMD) Always Below 1 Ω



d.

Connect No. 3 engine room wire.


Result:
Proceed to
OK
NG



OK

10.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - DC/DC-S FUSE)

NG

REPLACE NO. 3 ENGINE ROOM WIRE

10.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - DC/DC-S FUSE)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect connector A13 from the inverter with converter assembly.


c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.
A258452C11
1.5,0.344 1.917,0.583 0.417,0.24 1.833,1.177 2.292,0.729 true 0.198,0.167 0.448,0.365 0.25,0.198 10 false *a 2.333,0.604 2.563,0.771 0.229,0.167 10 false S 1.583,0.375 1.854,0.542 0.271,0.167 10 false A13
*a Front view of wire harness connector
(to Inverter with Converter Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A13-3 (S) - Body ground Always Same as auxiliary battery voltage



e.

Disconnect the cable from the negative (-) auxiliary battery terminal.


f.

Connect the inverter with converter assembly connector.

Result:
Proceed to
OK
NG




OK

11.CHECK HARNESS AND CONNECTOR (RESISTANCE VALUE OF NODD INSIDE POWER MANAGEMENT CONTROL ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK HARNESS AND CONNECTOR (RESISTANCE VALUE OF NODD INSIDE POWER MANAGEMENT CONTROL ECU)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect connector A13 from the inverter with converter assembly.


c.
A258452C13
1.5,0.344 1.917,0.583 0.417,0.24 1.438,1.344 1.021,1.615 false 0.24,0.146 0.49,0.333 0.25,0.188 10 false *a 0.625,1.563 1.125,1.76 0.5,0.198 10 false NODD 1.573,0.385 1.844,0.552 0.271,0.167 10 false A13
*a Front view of wire harness connector
(to Inverter with Converter Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A13-5 (NODD) - Body ground Power switch off 110 to 150 kΩ



d.

Connect the inverter with converter assembly connector.

Result:
Proceed to
OK
NG




OK

12.CHECK DC/DC CONVERTER FUNCTION

NG

21.INSPECT POWER MANAGEMENT CONTROL ECU (RESISTANCE VALUE OF NODD INSIDE POWER MANAGEMENT CONTROL ECU)
12.CHECK DC/DC CONVERTER FUNCTION
HINT:

The current at the AMD terminal cannot be measured directly because of space limitations. Measure the current flowing at the auxiliary battery instead.


a.

Connect the AC/DC 400 A probe to the positive auxiliary battery line.


b.

Install the service plug grip.


c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Turn the power switch on (READY) and leave the vehicle as it is until the electric current flowing into the auxiliary battery becomes 10 A or less.

HINT:

If the power switch turns off immediately after it is turned on (READY), auxiliary battery voltage may be low. Recharge the auxiliary battery and perform this procedure again.



e.
A174427E06
0.978,0.503 1.57,0.844 0.591,0.341 10 Probe Direction 0.165,1.637 1.164,2.145 0.999,0.508 10 Current Flowing into Auxiliary Battery 0.652,0.955 0.835,0.583 0.835,0.583 0.95,0.583 false

A174428E06
0.996,0.355 1.587,0.696 0.591,0.341 10 Probe Direction 0.182,1.489 1.181,1.997 0.999,0.508 10 Current Flowing from Auxiliary Battery 0.669,0.807 0.852,0.435 0.852,0.435 0.967,0.435 false

Measure the current flowing from the auxiliary battery with the power switch on (READY), the headlight position switch and blower motor switch in the HI position, and the rear window defogger turned on.

Standard Current:
Item Condition Specified Condition
Current flowing from auxiliary battery Power switch on (READY)
(The headlight position switch and blower motor switch are in the HI position, and the rear window defogger is turned on.)
0 A or less
(no current from auxiliary battery)



f.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Item Condition Specified Condition
Auxiliary battery voltage Power switch on (READY)
(The headlight position switch and blower motor switch are in the HI position, and the rear window defogger is turned on.)
13 to 15 V



g.

Turn the power switch off.

Result:
Proceed to
OK
NG




OK

13.CHECK QUANTITY OF HV COOLANT

NG

REPLACE INVERTER WITH CONVERTER ASSEMBLY

13.CHECK QUANTITY OF HV COOLANT

A

14.CHECK COOLANT HOSE

B

ADD HV COOLANT

C

INSPECT FOR HV COOLANT LEAK AND ADD HV COOLANT

14.CHECK COOLANT HOSE

OK

15.PERFORM ACTIVE TEST USING GTS (CONTROL THE ELECTRIC COOLING FAN)

NG

CORRECT THE PROBLEM

15.PERFORM ACTIVE TEST USING GTS (CONTROL THE ELECTRIC COOLING FAN)

OK

16.CHECK HV COOLANT (CHECK FOR CONDITIONS THAT MAY HAVE CAUSED FREEZING)

NG

16.CHECK HV COOLANT (CHECK FOR CONDITIONS THAT MAY HAVE CAUSED FREEZING)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / DTC.

Powertrain > Hybrid Control > Trouble Codes
50001 236

d.

Read the freeze frame data Ambient Temperature using the GTS.


e.

Check if the freeze frame data Ambient Temperature is below freezing.

Result:
Result Proceed to
Ambient Temperature value is above freezing temperature of the HV coolant. A
Ambient Temperature value is below freezing temperature of the HV coolant. B


HINT:
·

HV coolant (SLLC) with a 30% concentration freezes at -15 °C (5°F) and HV coolant (SLLC) with a 50% concentration freezes at -35°C (-31°F).

·

If the HV coolant freezes in the HV radiator or HV water pump, the coolant temperature in the inverter with converter assembly rises because the HV coolant cannot circulate. As a result, a DTC may be set.

·

A DTC is set when the water pump impeller cannot rotate due to freezing of the HV coolant.

·

If a DTC is set due to freezing of HV coolant, the problem cannot be reproduced. Judge whether freezing of HV coolant occurred according to the freeze point of the HV coolant, HV coolant change history and ambient temperature when the DTC was set.




f.

Turn the power switch off.



A

REPLACE INVERTER WITH CONVERTER ASSEMBLY

B

22.REPLACE HV COOLANT
17.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - DC/DC-S FUSE)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect connector A13 from the inverter with converter assembly.


c.
A259800C05
2.177,1.406 2.74,1.469 true 0.156,0.125 0.354,0.313 0.198,0.188 10 false *1 2.76,1.385 2.958,1.573 0.198,0.188 10 false *2
*1 Engine Room Relay Block and Junction Block Assembly
*2 DC/DC-S Fuse


Remove the DC/DC-S fuse from the engine room relay block and junction block assembly.


d.

Measure the resistance according to the value(s) in the table below.

A259802C03
1.875,1.927 2.208,2.125 0.333,0.198 2.094,1.281 2.219,0.854 false 0.917,0.188 1.135,0.438 0.219,0.25 10 false *a 3.646,0.188 3.833,0.448 0.188,0.26 10 false *1 5.75,0.635 5.938,0.896 0.188,0.26 10 false *2 2.198,0.688 2.354,0.865 0.156,0.177 10 false S 1.917,1.948 2.188,2.115 0.271,0.167 10 false A13
*1 Engine Room Relay Block and Junction Block Assembly *2 DC/DC-S Fuse
*a Front view of wire harness connector
(to Inverter with Converter Assembly)
- -


Standard Resistance:
Tester Connection Switch Condition Specified Condition
A13-3 (S) or 2 (DC/DC-S fuse) - Body ground and other terminals Power switch off 10 kΩ or higher



e.

Install the DC/DC-S fuse.


f.

Connect the inverter with converter assembly connector.


Result:
Proceed to
OK
NG



OK

18.REPLACE INVERTER WITH CONVERTER ASSEMBLY

NG

23.REPAIR OR REPLACE HARNESS OR CONNECTOR
18.REPLACE INVERTER WITH CONVERTER ASSEMBLY

NEXT

REPLACE FUSE (DC/DC-S)

19.CHECK HYBRID VEHICLE TRANSAXLE ASSEMBLY (MG1)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
A258951

Remove the upper inverter cover (generator cable side) from the inverter with converter assembly.


c.
A258953C03
2.073,0.594 2.365,0.479 true 2.396,0.385 2.594,0.552 0.198,0.167 10 true *1
*1 Generator Cable


Disconnect the generator cable from the inverter with converter assembly.


d.
A258955C19
2.708,1 3.073,1.24 0.365,0.24 1.448,1.208 1.302,1.604 false 1.76,1.208 1.74,1.656 false 2.208,1.219 2.302,1.646 false 0.667,0.99 1.177,0.854 false 0.083,0.042 0.313,0.24 0.229,0.198 10 false *a 0.458,0.927 0.688,1.125 0.229,0.198 10 false *1 1.219,1.615 1.438,1.781 0.219,0.167 10 false W 1.698,1.667 1.917,1.865 0.219,0.198 10 false V 2.271,1.646 2.469,1.844 0.198,0.198 10 false U 2.813,1.042 3.021,1.208 0.208,0.167 10 false o1
*1 Shield Ground
*a Generator Cable
(Inverter with Converter Assembly Side)


Using a megohmmeter set to 500 V, measure the insulation resistance according to the value(s) in the table below.

NOTICE:

Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than 500 V can result in damage to the component being inspected.


Standard Resistance:
Tester Connection Switch Condition Specified Condition
o1-1 (W) - Body ground and shield ground Power switch off 100 MΩ or higher
o1-2 (V) - Body ground and shield ground Power switch off 100 MΩ or higher
o1-3 (U) - Body ground and shield ground Power switch off 100 MΩ or higher



e.

Connect the generator cable.


f.

Install the upper inverter cover.

Result:
Proceed to
OK
NG




OK

20.CHECK HYBRID VEHICLE TRANSAXLE ASSEMBLY (MG2)

NG

REPLACE HYBRID VEHICLE TRANSAXLE ASSEMBLY

20.CHECK HYBRID VEHICLE TRANSAXLE ASSEMBLY (MG2)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
A258951

Remove the upper inverter cover (motor cable side) from the inverter with converter assembly.


c.
A258954C03
1.052,0.49 0.729,0.594 false 0.542,0.552 0.698,0.708 0.156,0.156 10 true *1
*1 Motor Cable


Disconnect the motor cable from the inverter with converter assembly.


d.
A258955C20
2.708,1 3.073,1.24 0.365,0.24 1.458,1.208 1.313,1.604 false 1.76,1.219 1.74,1.667 false 2.208,1.219 2.302,1.646 false 0.667,0.99 1.177,0.854 false 0.083,0.042 0.313,0.24 0.229,0.198 10 false *a 0.458,0.927 0.688,1.125 0.229,0.198 10 false *1 1.219,1.615 1.438,1.781 0.219,0.167 10 false W 1.698,1.667 1.917,1.865 0.219,0.198 10 false V 2.271,1.646 2.469,1.844 0.198,0.198 10 false U 2.813,1.031 3.021,1.198 0.208,0.167 10 false n1
*1 Shield Ground
*a Motor Cable
(Inverter with Converter Assembly Side)


Using a megohmmeter set to 500 V, measure the insulation resistance according to the value(s) in the table below.

NOTICE:

Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than 500 V can result in damage to the component being inspected.


Standard Resistance:
Tester Connection Switch Condition Specified Condition
n1-1 (W) - Body ground and shield ground Power switch off 100 MΩ or higher
n1-2 (V) - Body ground and shield ground Power switch off 100 MΩ or higher
n1-3 (U) - Body ground and shield ground Power switch off 100 MΩ or higher



e.

Connect the motor cable.


f.

Install the upper inverter cover.

Result:
Proceed to
OK
NG




OK

REPLACE INVERTER WITH CONVERTER ASSEMBLY

NG

REPLACE HYBRID VEHICLE TRANSAXLE ASSEMBLY

21.INSPECT POWER MANAGEMENT CONTROL ECU (RESISTANCE VALUE OF NODD INSIDE POWER MANAGEMENT CONTROL ECU)
a.

Disconnect all the connectors from the power management control ECU.


b.
A204442C43
0.573,2.625 0.99,2.865 0.417,0.24 1.906,2.625 2.271,2.865 0.365,0.24 1.823,1.823 1.979,2.385 false 0.771,1.969 0.573,2.406 false 0.198,0.104 0.594,0.469 0.396,0.365 10 false *a 0.385,2.427 1.135,2.688 0.75,0.26 10 false NODD 1.927,2.406 2.365,2.635 0.438,0.229 10 false E1 0.656,2.677 1.063,2.917 0.406,0.24 10 false A38 2.031,2.677 2.313,2.927 0.281,0.25 10 false I3
*a Component without harness connected
(Power Management Control ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A38-23 (NODD) - I3-6 (E1) Power switch off 110 to 150 kΩ



c.

Connect the power management control ECU connectors.

Result:
Proceed to
OK
NG




OK

REPAIR OR REPLACE HARNESS OR CONNECTOR

NG

22.REPLACE HV COOLANT

NEXT

COMPLETED

23.REPAIR OR REPLACE HARNESS OR CONNECTOR
Result:
Proceed to
NEXT



NEXT

REPLACE FUSE (DC/DC-S)