Home › Engine / Hybrid System › 2AR-FXE COOLING › COOLING FAN SYSTEM
RM2040EQ _51 Engine / Hybrid System _014697 2AR-FXE COOLING _0074927 COOLING FAN SYSTEM J

2AR-FXE COOLING  COOLING FAN SYSTEM  Cooling Fan Circuit  


DESCRIPTION

The ECM calculates an appropriate cooling fan speed based on the engine coolant temperature, air conditioning switch condition, refrigerant pressure, engine speed and vehicle speed, and sends the signals to the cooling fan ECU to regulate the cooling fans. The cooling fan ECU controls the cooling fan speed based on the duty ratio signal sent from the ECM. By basing its control on the operating conditions, the ECM can control the fan speed optimally using the cooling fan ECU, achieving both high cooling performance and quietness.

WIRING DIAGRAM

A270194
0.521,3.479 1.177,3.823 0.656,0.344 10 false Auxiliary Battery 1.969,2.344 2.583,2.542 0.615,0.198 10 false IG1 No. 2 4.167,0.917 4.469,1.083 0.302,0.167 10 false FAN 1.958,1.083 2.917,1.26 0.958,0.177 10 false ECU-IG1 No. 1 0.427,2.906 1,3.073 0.573,0.167 10 false MAIN 1.823,0.427 2.115,0.594 0.292,0.167 10 false FAN 4.146,2.708 4.51,2.854 0.365,0.146 10 false ECM 2.104,3.833 2.531,3.99 0.427,0.156 10 false IG1D 4.135,2.26 4.458,2.406 0.323,0.146 10 false RFC 5.156,0.25 5.479,0.396 0.323,0.146 10 false +B1 5.167,2.25 5.344,2.396 0.177,0.146 10 false SI 5.156,3.542 5.479,3.688 0.323,0.146 10 false E1 5.948,1.823 7.115,2 1.167,0.177 10 false Cooling Fan Motor 6.188,3.344 7.063,3.677 0.875,0.333 10 false No. 2 Cooling Fan Motor 4.917,4.177 6.042,4.354 1.125,0.177 10 false Cooling Fan ECU 1.042,4.271 4.073,4.5 3.031,0.229 10 false Power Management Control ECU 1.552,2.844 3.229,3.26 1.677,0.417 10 false Instrument Panel Junction Block Assembly 0.896,1.198 1.094,1.365 0.198,0.167 10 false 1 1.01,2.646 1.135,2.813 0.125,0.167 10 false 7 1.198,2.656 1.396,2.823 0.198,0.167 10 false 3B 2.51,3.729 2.635,3.896 0.125,0.167 10 false 2 3.344,0.948 3.542,1.115 0.198,0.167 10 false 3D 3.344,0.771 3.542,0.938 0.198,0.167 10 false 36 3.167,2.656 3.365,2.823 0.198,0.167 10 false 3A 2.906,2.656 3.104,2.823 0.198,0.167 10 false 27 3.844,2.719 4.135,2.885 0.292,0.167 10 false A25 1.042,4.115 1.333,4.281 0.292,0.167 10 false I4 4.844,3.365 4.969,3.531 0.125,0.167 10 false 1 4.875,2.073 5,2.24 0.125,0.167 10 false 2 4.479,2.167 4.677,2.333 0.198,0.167 10 false 44 4.552,0.167 4.677,0.333 0.125,0.167 10 false 5 3.979,0.177 4.104,0.344 0.125,0.167 10 false 3 4.552,0.604 4.677,0.771 0.125,0.167 10 false 2 3.969,0.604 4.094,0.771 0.125,0.167 10 false 1 4.865,0.104 4.99,0.271 0.125,0.167 10 false 3 4.813,3.552 5.104,3.719 0.292,0.167 10 false A10 4.802,0.26 5.094,0.427 0.292,0.167 10 false A10 4.813,2.26 5.104,2.427 0.292,0.167 10 false A10 5.906,1.094 6.198,1.26 0.292,0.167 10 false z14 5.896,1.542 6.188,1.708 0.292,0.167 10 false z14 5.948,1.375 6.073,1.542 0.125,0.167 10 false 1 5.948,0.927 6.073,1.094 0.125,0.167 10 false 2 5.896,2.583 6.188,2.75 0.292,0.167 10 false z15 5.896,3.042 6.188,3.208 0.292,0.167 10 false z15 5.938,2.865 6.063,3.031 0.125,0.167 10 false 1 5.979,2.354 6.104,2.521 0.125,0.167 10 false 2 0.875,1.365 1.073,1.531 0.198,0.167 10 false 3F 0.427,1.844 0.698,2.292 0.271,0.448 10 false DC/ DC

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE ELECTRIC COOLING FAN)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Electric Cooling Fan.

Powertrain > Engine and ECT > Active Test
Tester Display
Control the Electric Cooling Fan
50004 234 16

e.

Check the operation of the cooling fans while operating them using the tester.


OK:
Tester Operation Specified Condition
ON Cooling fans operating
OFF Cooling fans stopped


Result:
Result Proceed to
OK A
NG (Cooling fans do not operate) B
NG (Cooling fans do not stop) C



A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

B

2.INSPECT COOLING FAN MOTOR (COOLING FAN MOTOR AND NO. 2 COOLING FAN MOTOR)

C

15.CHECK HARNESS AND CONNECTOR (ECM - COOLING FAN ECU)
2.INSPECT COOLING FAN MOTOR (COOLING FAN MOTOR AND NO. 2 COOLING FAN MOTOR)
a.

Inspect the cooling fan motor and No. 2 cooling fan motor.

Click hereEngine / Hybrid System>2AR-FXE COOLING>COOLING FAN SYSTEM>ON-VEHICLE INSPECTION


Result:
Result Proceed to
OK A
NG (Cooling fan motor) B
NG (No. 2 cooling fan motor) C



A

3.CHECK HARNESS AND CONNECTOR (COOLING FAN ECU POWER SOURCE)

B

C

REPLACE NO.2 COOLING FAN MOTOR

3.CHECK HARNESS AND CONNECTOR (COOLING FAN ECU POWER SOURCE)
a.
A254660
0.573,1.146 0.875,1.406 0.302,0.26 0.885,1.865 1.333,1.302 false 2.115,1.323 2.469,1.865 false 0.604,1.188 1.063,1.385 0.458,0.198 10 false A10 0.125,0.156 0.583,0.354 0.458,0.198 10 false *a 0.771,1.885 1.229,2.083 0.458,0.198 10 false E1 2.375,1.885 2.833,2.083 0.458,0.198 10 false +B1
*a Front view of wire harness connector
(to Cooling Fan ECU)


Disconnect the cooling fan ECU connector.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A10-3 (+B1) - A10-1 (E1) Power switch on (IG) 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (ECM - COOLING FAN ECU)

NG

5.CHECK HARNESS AND CONNECTOR (COOLING FAN ECU - BODY GROUND)
4.CHECK HARNESS AND CONNECTOR (ECM - COOLING FAN ECU)
a.

Disconnect the ECM connector.


b.

Disconnect the cooling fan ECU connector.


c.

Measure the resistance according to the value(s) in the table below.


Standard Resistance:
Tester Connection Condition Specified Condition
A25-44 (RFC) or A10-2 (SI) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - COOLING FAN ECU)

5.CHECK HARNESS AND CONNECTOR (COOLING FAN ECU - BODY GROUND)
a.

Disconnect the cooling fan ECU connector.


b.

Measure the resistance according to the value(s) in the table below.


Standard Resistance:
Tester Connection Condition Specified Condition
A10-1 (E1) - Body ground Always Below 1 Ω


Result:
Proceed to
OK
NG



OK

6.INSPECT FAN RELAY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (COOLING FAN ECU - BODY GROUND)

6.INSPECT FAN RELAY

Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (FAN RELAY POWER SOURCE)

NG

REPLACE FAN RELAY

7.CHECK HARNESS AND CONNECTOR (FAN RELAY POWER SOURCE)
a.

Remove the FAN relay from the engine room relay block and junction block assembly.


A264817
0.604,1.969 0.917,2.167 0.313,0.198 10 false *2 2.24,0.667 2.552,0.865 0.313,0.198 10 false *1
*1 Engine Room Relay Block and Junction Block Assembly
*2 FAN Relay


b.

Measure the voltage according to the value(s) in the table below.


Standard Voltage:
Tester Connection Condition Specified Condition
3 (FAN relay) - Body ground Power switch off 11 to 14 V


Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (COOLING FAN ECU - FAN RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (FAN RELAY - AUXILIARY BATTERY)

8.CHECK HARNESS AND CONNECTOR (COOLING FAN ECU - FAN RELAY)
a.

Remove the FAN relay from the engine room relay block and junction block assembly.


b.

Disconnect the cooling fan ECU connector.


c.

Measure the resistance according to the value(s) in the table below.


Standard Resistance:
Tester Connection Condition Specified Condition
A10-3 (+B1) - 5 (FAN relay) Always Below 1 Ω
A10-3 (+B1) or 5 (FAN relay) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (FAN RELAY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (COOLING FAN ECU - FAN RELAY)

9.CHECK HARNESS AND CONNECTOR (FAN RELAY - BODY GROUND)
a.

Remove the FAN relay from the engine room relay block and junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.


Standard Resistance:
Tester Connection Condition Specified Condition
2 (FAN relay) - Body ground Always Below 1 Ω


Result:
Proceed to
OK
NG



OK

10.CHECK HARNESS AND CONNECTOR (FAN RELAY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (FAN RELAY - BODY GROUND)

10.CHECK HARNESS AND CONNECTOR (FAN RELAY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Remove the FAN relay from the engine room relay block and junction block assembly.


b.

Disconnect the instrument panel junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.


Standard Resistance:
Tester Connection Condition Specified Condition
1 (FAN relay) - 3D-36 Always Below 1 Ω
1 (FAN relay) or 3D-36 - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



OK

11.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (IG1 NO. 2 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (FAN RELAY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

11.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (IG1 NO. 2 RELAY)
a.

Disconnect the instrument panel junction block assembly connector.


b.

Measure the resistance according to the value(s) in the table below.


A284396
6.281,1.208 6.542,1.396 0.26,0.188 6.292,2.333 6.552,2.521 0.26,0.188 3.646,3.198 3.906,3.385 0.26,0.188 3.615,2.344 3.875,2.531 0.26,0.188 1.135,1 1.448,1.156 0.313,0.156 10 false *1 6.292,1.229 6.625,1.427 0.333,0.198 10 false 3B 6.333,2.344 6.667,2.542 0.333,0.198 10 false 3A 3.667,2.365 4,2.563 0.333,0.198 10 false 3D 3.698,3.219 4.031,3.417 0.333,0.198 10 false 3F
*1 Instrument Panel Junction Block Assembly - -


Standard Resistance:
Tester Connection Condition Specified Condition
3F-1 - 3D-36 Auxiliary battery voltage is not applied between terminals 3A-27 and 3B-7 10 kΩ or higher
3F-1 - 3D-36 Auxiliary battery voltage is applied between terminals 3A-27 and 3B-7 Below 1 Ω


Result:
Proceed to
OK
NG



OK

12.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY POWER SOURCE)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (IG1 NO. 2 RELAY)

12.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY POWER SOURCE)
a.

Disconnect the instrument panel junction block assembly connector.


A258462
0.531,1.021 0.813,1.281 0.281,0.26 0.594,1.073 0.906,1.271 0.313,0.198 10 false 3F 0.156,0.167 0.469,0.365 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to Instrument Panel Junction Block Assembly)


b.

Measure the voltage according to the value(s) in the table below.


Standard Voltage:
Tester Connection Condition Specified Condition
3F-1 - Body ground Power switch off 11 to 14 V


Result:
Proceed to
OK
NG



OK

13.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - AUXILIARY BATTERY)

13.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - BODY GROUND)
a.

Disconnect the instrument panel junction block assembly connector.


b.

Measure the resistance according to the value(s) in the table below.


Standard Resistance:
Tester Connection Condition Specified Condition
3B-7 - Body ground Always Below 1 Ω


Result:
Proceed to
OK
NG



OK

14.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - POWER MANAGEMENT CONTROL ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - BODY GROUND)

14.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - POWER MANAGEMENT CONTROL ECU)
a.

Disconnect the instrument panel junction block assembly connector.


b.

Disconnect the power management control ECU connector.


c.

Measure the resistance according to the value(s) in the table below.


Standard Resistance:
Tester Connection Condition Specified Condition
3A-27 - I4-2 (IG1D) Always Below 1 Ω
3A-27 or I4-2 (IG1D) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - POWER MANAGEMENT CONTROL ECU)

15.CHECK HARNESS AND CONNECTOR (ECM - COOLING FAN ECU)
a.

Disconnect the ECM connector.


b.

Disconnect the cooling fan ECU connector.


c.

Measure the resistance according to the value(s) in the table below.


Standard Resistance:
Tester Connection Condition Specified Condition
A25-44 (RFC) - A10-2 (SI) Always Below 1 Ω


Result:
Proceed to
OK
NG



OK

16.CHECK HARNESS AND CONNECTOR (COOLING FAN MOTOR - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - COOLING FAN ECU)

16.CHECK HARNESS AND CONNECTOR (COOLING FAN MOTOR - BODY GROUND)
a.

Disconnect the cooling fan motor connector.


A255683
0.656,1.198 1.01,1.458 0.354,0.26 0.74,1.25 1.198,1.448 0.458,0.198 10 false z14 0.167,0.167 0.625,0.365 0.458,0.198 10 false *a
*a Component without harness connected
(Cooling Fan Motor)


b.

Measure the resistance according to the value(s) in the table below.


Standard Resistance:
Tester Connection Condition Specified Condition
z14-1 - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



OK

17.CHECK HARNESS AND CONNECTOR (NO. 2 COOLING FAN MOTOR - BODY GROUND)

NG

17.CHECK HARNESS AND CONNECTOR (NO. 2 COOLING FAN MOTOR - BODY GROUND)
a.

Disconnect the No. 2 cooling fan motor connector.


A255684
0.635,1.229 0.979,1.5 0.344,0.271 0.698,1.292 1.156,1.49 0.458,0.198 10 false z15 0.156,0.167 0.615,0.365 0.458,0.198 10 false *a
*a Component without harness connected
(No. 2 Cooling Fan Motor)


b.

Measure the resistance according to the value(s) in the table below.


Standard Resistance:
Tester Connection Condition Specified Condition
z15-1 - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPLACE NO.2 COOLING FAN MOTOR