Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › from 2016.05
RM2040EQ _51 Engine / Hybrid System _014692 HYBRID / BATTERY CONTROL _0074885 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P0A90-509  Drive Motor "A" Performance  


DESCRIPTION

For a description of MG2 (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0A90-251).

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P0A90-509 Drive Motor "A" Performance Motor system malfunction
·

Hybrid vehicle transaxle assembly

·

Inverter with converter assembly

·

Wire harness or connector

·

Power management control ECU


Comes on Master Warning Light:
Comes on

WIRING DIAGRAM

Refer to the wiring diagram for DTC P0AA6-526 (Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0AA6-526).

Refer to the wiring diagram for DTC P321E-318 (Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P321E-318).

CAUTION / NOTICE / HINT

CAUTION:
·

Before inspecting the high-voltage system or disconnecting the low voltage connector of the inverter with converter assembly, take safety precautions such as wearing insulated gloves and removing the service plug grip to prevent electrical shocks. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·

After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION).

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.




NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


PROCEDURE

1.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / DTC.

Powertrain > Hybrid Control > Trouble Codes
50001 236

d.

Check if DTCs are output.

Result:
Result Proceed to
Only P0A90-509 is output or P0A90-509 and DTCs other than the ones in the table below are also output. A
Any of the following DTCs are also output. B


DTC No. Relevant Diagnosis
P06B0-163 Sensor Power Supply "A" Circuit / Open
P06D6-511 Sensor Reference Voltage "F" Circuit / Open
P06E6-164 Sensor Power Supply "C" Circuit / Open
P0A1A-151, 166, 517, 658, 791, 809 Generator Control Module
P0A1B-198, 503, 505, 547, 554, 786, 794, 806 Drive Motor "A" Control Module
P0A1D (all INF codes)*1 Hybrid Powertrain Control Module
P0A3F-243 Drive Motor "A" Position Sensor Circuit
P0A40-500, 504, 506, 549, 556, 808 Drive Motor "A" Position Sensor Circuit Range / Performance
P0A41-245 Drive Motor "A" Position Sensor Circuit Low
P0A4B-253 Generator Position Sensor Circuit
P0A4C-513, 518, 811 Generator Position Sensor Circuit Range / Performance
P0A4D-255 Generator Position Sensor Circuit Low
P0A78-202, 279, 287, 548, 555, 807 Drive Motor "A" Inverter Performance
P0A7A-325, 810 Generator Inverter Performance
P0AA6 (all INF codes)*1 Hybrid Battery Voltage System Isolation Fault
P0BEA-290 Drive Motor "A" Phase V Current Sensor Circuit Range / Performance
P0BEE-298 Drive Motor "A" Phase W Current Sensor Circuit Range / Performance
P0C76-523 Hybrid Battery System Discharge Time Too Long
P0D2E-586 Drive Motor "A" Inverter Voltage Sensor Circuit Range / Performance
P0D2F-266 Drive Motor "A" Inverter Voltage Sensor Circuit Low
P0D30-267 Drive Motor "A" Inverter Voltage Sensor Circuit High
P0E05-328 Generator Phase V Current Sensor Circuit Range / Performance
P0E09-336 Generator Phase W Current Sensor Circuit Range / Performance
P0E32-585 DC/DC Converter Voltage Sensor "A" Range / Performance
P0E33-589 DC/DC Converter Voltage Sensor "A" Low
P0E34-590 DC/DC Converter Voltage Sensor "A" High
P1C2A-155 Generator A/D Converter Circuit
P1C2B-192 Drive Motor "A" A/D Converter Circuit
P1C2D-587 Hybrid Battery Voltage / DC/DC Converter Voltage Correlation
P1C3C-294 Drive Motor "A" Phase V Current Sensor Correlation
P1C3D-302 Drive Motor "A" Phase W Current Sensor Correlation
P1C3E-333 Generator Phase V Current Sensor Correlation
P1C3F-341 Generator Phase W Current Sensor Correlation
P1C4A-288 Drive Motor "A" Phase V Current Sensor Sub Circuit Range / Performance
P1C4F-296 Drive Motor "A" Phase W Current Sensor Sub Circuit Range / Performance
P1C54-326 Generator Phase V Current Sensor Sub Circuit Range / Performance
P1C59-334 Generator Phase W Current Sensor Sub Circuit Range / Performance
P1C6D-501 Drive Motor "A" Phase V Current Sensor Offset Range / Performance
P1C6E-502 Drive Motor "A" Phase W Current Sensor Offset Range / Performance
P1C71-515 Generator Phase V Current Sensor Offset Range / Performance
P1C72-516 Generator Phase W Current Sensor Offset Range / Performance
P1C73-512 Sensor Standard Voltage "F" Circuit / Open
P1CA6-156 Generator Control Module Malfunction
P1CA7-193 Drive Motor Control Module Malfunction
P1CAC-200 Generator Position Sensor Angle Malfunction
P1CAD-168 Drive Motor "A" Position Sensor Angle Malfunction
P1CAF-792 Generator Position Sensor REF Signal Cycle Malfunction
P1CB0-795 Drive Motor "A" Position Sensor REF Signal Cycle Malfunction
P1CB2-793 Generator Position Sensor REF Signal Stop Malfunction
P1CB3-796 Drive Motor "A" Position Sensor REF Signal Stop Malfunction
P3004-132 High Voltage Power Resource
P3133-659 Communication Error from Generator to Drive Motor "A"
P3134-661 Communication Error from Drive Motor "A" to Generator

HINT:
·

*1: If any INF codes are output for this DTC, refer to the corresponding diagnostic procedure.

·

P0A90-509 may be output due to a malfunction which causes the DTCs in the table above to be output. In this case, first troubleshoot the output DTCs in the table above. Then, perform a reproduction test to check that no DTCs are output.




e.

Turn the power switch off.



A

2.CHECK DTC OUTPUT (HYBRID CONTROL)

B

2.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / DTC.

Powertrain > Hybrid Control > Trouble Codes
50001 236

d.

Check if DTCs are output.

Result:
Result Proceed to
Any of the following DTCs are also output. A
Only P0A90-509 is output or P0A90-509 and DTCs other than the ones in the table below are also output. B


DTC No. Relevant Diagnosis
P0A92-261, 521 Hybrid Generator Performance
P0E71-344 Generator Torque Delivered Performance

HINT:

When the DTCs listed in the table above are also output, there may be a short between the HSDN (MG shut down signal) circuit and power circuit.



e.

Turn the power switch off.



A

3.CHECK POWER MANAGEMENT CONTROL ECU

B

4.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WITH CONVERTER ASSEMBLY CONNECTOR)
3.CHECK POWER MANAGEMENT CONTROL ECU

OK

4.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WITH CONVERTER ASSEMBLY CONNECTOR)

NG

7.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - INVERTER WITH CONVERTER ASSEMBLY)
4.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WITH CONVERTER ASSEMBLY CONNECTOR)

OK

5.CHECK INVERTER WITH CONVERTER ASSEMBLY (MOTOR CABLE CONNECTION CONDITION)

NG

CONNECT SECURELY

5.CHECK INVERTER WITH CONVERTER ASSEMBLY (MOTOR CABLE CONNECTION CONDITION)

A

6.CHECK HYBRID VEHICLE TRANSAXLE ASSEMBLY (MG2)

B

REPLACE MALFUNCTIONING PARTS

C

CONNECT SECURELY

6.CHECK HYBRID VEHICLE TRANSAXLE ASSEMBLY (MG2)

OK

REPLACE INVERTER WITH CONVERTER ASSEMBLY

NG

REPLACE HYBRID VEHICLE TRANSAXLE ASSEMBLY

7.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - INVERTER WITH CONVERTER ASSEMBLY)

OK

8.CHECK INVERTER WITH CONVERTER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK INVERTER WITH CONVERTER ASSEMBLY

OK

NG

REPLACE INVERTER WITH CONVERTER ASSEMBLY