Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › from 2016.05
RM2040EQ _51 Engine / Hybrid System _014692 HYBRID / BATTERY CONTROL _0074885 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P3004-131  High Voltage Power Resource  


DESCRIPTION

Refer to the description for DTC P0AE6-225 (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0AE6-225).

The power management control ECU monitors the high-voltage wiring between the HV battery and the inverter with converter assembly and detects the following malfunction.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P3004-131 High Voltage Power Resource One of the following occurs during pre-charge (the time from when SMRP turns on until SMRG turns on):
·

Electric battery fuse in the service plug grip has an open circuit

·

Service plug grip is not installed

·

SMRP remains open

·

SMRB remains open

·

Precharge resistor has an open circuit

·

High voltage cable has an open circuit


·

Hybrid battery junction block assembly

·

No. 4 floor wire

·

Inverter with converter assembly

·

HV battery

·

Wire harness or connector


Does not come on Master Warning Light:
Comes on

WIRING DIAGRAM

Refer to the wiring diagram for DTC P0AA6-526 (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0AA6-526).

Refer to the wiring diagram for DTC P0AE6-225 (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0AE6-225).


CAUTION / NOTICE / HINT

CAUTION:
·

Before inspecting the high-voltage system or disconnecting the low voltage connector of the inverter with converter assembly, take safety precautions such as wearing insulated gloves and removing the service plug grip to prevent electrical shocks. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·

After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION).

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.


·

When disposing of an HV battery, make sure to return it through an authorized collection agent who is capable of handling it safely. If the HV battery is returned via the manufacturer specified route, it will be returned properly and in a safe manner by an authorized collection agent.



NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


PROCEDURE

1.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / DTC.


d.

Check if DTCs are output.

Powertrain > Hybrid Control > Trouble Codes
50001 236
Result:
Result Proceed to
P3004-131 only is output. A
DTCs shown in Table 1 are output simultaneously. B
DTCs shown in Table 2 are output simultaneously. C


Table 1
DTC No. Relevant Diagnosis
P06E6-164 Sensor Power Supply "C" Circuit / Open
P0A1A-151, 658 Generator Control Module
P0A1B-786 Drive Motor "A" Control Module
P0A1D (all INF codes)*1 Hybrid Powertrain Control Module
P0ADB-227 Hybrid Battery Positive Contactor Control Circuit Low
P0ADC-226 Hybrid Battery Positive Contactor Control Circuit High
P0ADF-229 Hybrid Battery Negative Contactor Control Circuit Low
P0AE0-228 Hybrid Battery Negative Contactor Control Circuit High
P0AE6-225 Hybrid Battery Precharge Contactor Control Circuit Low
P0AE7-224 Hybrid Battery Precharge Contactor Control Circuit High
P0C76-523 Hybrid Battery System Discharge Time Too Long
P0CA3-442 DC/DC Converter Step Up Voltage Performance
P0D2E-586 Drive Motor "A" Inverter Voltage Sensor Circuit Range / Performance
P0D2F-266 Drive Motor "A" Inverter Voltage Sensor Circuit Low
P0D30-267 Drive Motor "A" Inverter Voltage Sensor Circuit High
P1C2A-155 Generator A/D Converter Circuit
P1C73-512 Sensor Standard Voltage "F" Circuit / Open
P1CA6-156 Generator Control Module Malfunction
P1CA7-193 Drive Motor Control Module Malfunction
P2511-149 ECM/PCM Power Relay Sense Circuit Intermittent
P3004-800, 801 High Voltage Power Resource
P3133-659 Communication Error from Generator to Drive Motor "A"
P3134-661 Communication Error from Drive Motor "A" to Generator
P324E-788 MG-ECU Power Relay Intermittent Circuit
U0110 (all INF codes)*1 Lost Communication with Drive Motor Control Module "A"

Table 2
DTC No. Relevant Diagnosis
P0A95-123 High Voltage Fuse
P0ABF-123 Hybrid Battery Pack Current Sensor Circuit
P0AC0-123 Hybrid Battery Pack Current Sensor Circuit Range / Performance
P0AC1-123 Hybrid Battery Pack Current Sensor "A" Circuit Low
P0AC2-123 Hybrid Battery Pack Current Sensor "A" Circuit High
P0AFC-123 Hybrid Battery Pack Sensor Module
P0B3D-123 Hybrid Battery Voltage Sensor "A" Circuit Low
P0B42-123 Hybrid Battery Voltage Sensor "B" Circuit Low
P0B47-123 Hybrid Battery Voltage Sensor "C" Circuit Low
P0B4C-123 Hybrid Battery Voltage Sensor "D" Circuit Low
P0B51-123 Hybrid Battery Voltage Sensor "E" Circuit Low
P0B56-123 Hybrid Battery Voltage Sensor "F" Circuit Low
P0B5B-123 Hybrid Battery Voltage Sensor "G" Circuit Low
P0B60-123 Hybrid Battery Voltage Sensor "H" Circuit Low
P0B65-123 Hybrid Battery Voltage Sensor "I" Circuit Low
P0B6A-123 Hybrid Battery Voltage Sensor "J" Circuit Low
P0B6F-123 Hybrid Battery Voltage Sensor "K" Circuit Low
P0B74-123 Hybrid Battery Voltage Sensor "L" Circuit Low
P0B79-123 Hybrid Battery Voltage Sensor "M" Circuit Low
P0B7E-123 Hybrid Battery Voltage Sensor "N" Circuit Low
P0B83-123 Hybrid Battery Voltage Sensor "O" Circuit Low
P0B88-123 Hybrid Battery Voltage Sensor "P" Circuit Low
P0B8D-123 Hybrid Battery Voltage Sensor "Q" Circuit Low
P0B92-123 Hybrid Battery Voltage Sensor "R" Circuit Low
P308A-123 Hybrid Battery Voltage Sensor All Circuits Low
U029A-123 Lost Communication with Hybrid Battery Pack Sensor Module

HINT:
·

*1: If any INF codes are output for this DTC, refer to the corresponding diagnostic procedure.

·

P3004-131 may be output due to a malfunction which causes the DTCs in the table above to be output. In this case, first troubleshoot the output DTCs in the table above. Then, perform a reproduction test to check that no DTCs are output.




e.

Turn the power switch off.



A

2.CHECK FREEZE FRAME DATA (HYBRID CONTROL)

B

C

2.CHECK FREEZE FRAME DATA (HYBRID CONTROL)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / DTC.


d.

Read the freeze frame data of DTC P3004-131.

Result:
Result Proceed to
Both of the following conditions are met:
·

Post-boost voltage (VH-Voltage after Boosting) is below 50 V.

·

Difference between HV battery voltage (Power Resource VB) and pre-boost voltage (VL-Voltage before Boosting) is 40 V or less.


A
Other than above B



e.

Turn the power switch off.



A

REPLACE INVERTER WITH CONVERTER ASSEMBLY

B

3.CHECK CONNECTOR CONNECTION CONDITION (POWER MANAGEMENT CONTROL ECU CONNECTOR)
3.CHECK CONNECTOR CONNECTION CONDITION (POWER MANAGEMENT CONTROL ECU CONNECTOR)

OK

4.CHECK INVERTER WITH CONVERTER ASSEMBLY (NO. 4 FLOOR WIRE CONNECTOR CONNECTION CONDITION)

NG

CONNECT SECURELY

4.CHECK INVERTER WITH CONVERTER ASSEMBLY (NO. 4 FLOOR WIRE CONNECTOR CONNECTION CONDITION)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
A259710

Remove the connector cover assembly from the inverter with converter assembly.


c.
A259712N04
1.5,0.865 1.99,1.156 0.49,0.292 1.667,0.917 1.927,1.094 0.26,0.177 10 true Q1

Check the connector Q1 connection condition between the No. 4 floor wire and the inverter with converter assembly.

Specified Condition:

T=8.0 N*m (82 kgf*cm, 71 in.*lbf)



d.

Disconnect connector Q1 of the No. 4 floor wire from the inverter with converter assembly.


e.

Check for arc marks on the terminals of the No. 4 floor wire.

Result:
Result Proceed to
The terminals are connected securely and there are no contact problems. There are no arc marks. A
The terminals are not connected securely and there is a contact problem. There are arc marks. B
The terminals are not connected securely and there is a contact problem. There are no arc marks. C
The terminals are connected securely and there are no contact problems. There are arc marks. B



f.

Connect the No. 4 floor wire to the inverter with converter assembly.


g.

Install the connector cover assembly to the inverter with converter assembly.



A

5.CHECK HV BATTERY JUNCTION BLOCK ASSEMBLY (NO. 4 FLOOR WIRE CONNECTOR CONNECTION CONDITION)

B

REPLACE MALFUNCTIONING PARTS

C

CONNECT SECURELY

5.CHECK HV BATTERY JUNCTION BLOCK ASSEMBLY (NO. 4 FLOOR WIRE CONNECTOR CONNECTION CONDITION)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 4 hybrid battery shield panel.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV RELAY ASSEMBLY>REMOVAL


c.
A259723N06
0.281,0.604 0.771,0.896 0.49,0.292 1.688,0.177 2.177,0.469 0.49,0.292 0.417,0.656 0.667,0.854 0.25,0.198 10 true Q3 1.854,0.229 2.052,0.406 0.198,0.177 10 true Q2

Check the connector Q2 and connector Q3 connection condition between the No. 4 floor wire and the hybrid battery junction block assembly.


d.

Disconnect connector Q2 and connector Q3 of the No. 4 floor wire from the hybrid battery junction block assembly.


e.

Check for arc marks on the terminals of the No. 4 floor wire.

Result:
Result Proceed to
The terminals are connected securely and there are no contact problems. There are no arc marks. A
The terminals are not connected securely and there is a contact problem. There are arc marks. B
The terminals are not connected securely and there is a contact problem. There are no arc marks. C
The terminals are connected securely and there are no contact problems. There are arc marks. B



f.

Connect the No. 4 floor wire to the hybrid battery junction block assembly.


g.

Install the No. 4 hybrid battery shield panel.



A

6.CHECK NO. 4 FLOOR WIRE (INVERTER WITH CONVERTER ASSEMBLY - HYBRID BATTERY JUNCTION BLOCK ASSEMBLY)

B

REPLACE MALFUNCTIONING PARTS

C

CONNECT SECURELY

6.CHECK NO. 4 FLOOR WIRE (INVERTER WITH CONVERTER ASSEMBLY - HYBRID BATTERY JUNCTION BLOCK ASSEMBLY)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
A259710

Remove the connector cover assembly from the inverter with converter assembly.


c.
A259712N04
1.5,0.865 1.99,1.156 0.49,0.292 1.667,0.917 1.927,1.094 0.26,0.177 10 true Q1

Disconnect connector Q1 of the No. 4 floor wire from the inverter with converter assembly.


d.

Remove the No. 4 hybrid battery shield panel.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV RELAY ASSEMBLY>REMOVAL


e.
A260212C02
0.802,1.417 1.167,1.656 0.365,0.24 1.427,2.875 1.771,3.104 0.344,0.229 0.667,3.469 1.01,3.708 0.344,0.24 1.333,1.948 1.49,1.656 false 2.104,1.958 1.969,1.635 false 0.073,0.052 0.385,0.208 0.313,0.156 10 false *a 0.083,2.438 0.396,2.594 0.313,0.156 10 false *b 0.854,1.458 1.167,1.656 0.313,0.198 10 false Q1 2.01,1.979 2.469,2.177 0.458,0.198 10 false CEI 1.219,1.979 1.677,2.177 0.458,0.198 10 false CBI 0.688,3.51 0.958,3.677 0.271,0.167 10 true Q3 1.469,2.885 1.729,3.083 0.26,0.198 10 true Q2
*a No. 4 floor wire
(Inverter with Converter Assembly Side)
*b Component with harness connected
(Hybrid Battery Junction Block Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Q2-1 (CBI) - Q1-1 (CBI) Power switch off Below 1 Ω
Q3-1 (CEI) - Q1-2 (CEI) Power switch off Below 1 Ω



f.

Install the No. 4 hybrid battery shield panel.


g.

Connect the No. 4 floor wire to the inverter with converter assembly.


h.

Install the connector cover assembly to the inverter with converter assembly.


Result:
Proceed to
OK
NG



OK

7.CHECK HV BATTERY JUNCTION BLOCK ASSEMBLY (HV BATTERY HIGH VOLTAGE TERMINAL CONNECTION CONDITION)

NG

7.CHECK HV BATTERY JUNCTION BLOCK ASSEMBLY (HV BATTERY HIGH VOLTAGE TERMINAL CONNECTION CONDITION)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 1 hybrid battery shield sub-assembly

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV RELAY ASSEMBLY>REMOVAL


c.
A259730

Check the connections between the HV battery high voltage terminals and the hybrid battery junction block assembly.

Specified Condition:

5.4 N*m (55 kgf*cm, 48 in.*lbf)



d.

Check for arc marks on the terminals of the HV battery high voltage terminals.

Result:
Result Proceed to
The terminals are connected securely and there are no contact problems. There are no arc marks. A
The terminals are not connected securely and there is a contact problem. There are arc marks. B
The terminals are not connected securely and there is a contact problem. There are no arc marks. C
The terminals are connected securely and there are no contact problems. There are arc marks. B



e.

Install the No. 1 hybrid battery shield sub-assembly.



A

8.CHECK HV BATTERY

B

REPLACE MALFUNCTIONING PARTS

C

CONNECT SECURELY

8.CHECK HV BATTERY
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 1 hybrid battery shield sub-assembly

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV RELAY ASSEMBLY>REMOVAL


c.
A260213E03
1.458,0.99 1.948,1.281 0.49,0.292 1.49,1.781 1.979,2.073 0.49,0.292 1.104,2.594 1.552,3.24 true 2.521,2.833 2.052,3.25 true 2.563,2.698 2.667,2.854 0.104,0.156 10 false 1 0.969,2.396 1.073,2.552 0.104,0.156 10 false 2 1.635,1.042 1.823,1.24 0.188,0.198 10 true A 1.625,1.823 1.854,2.021 0.229,0.198 10 true q1

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A-1 (+) - Service plug grip terminal 1 Power switch off 114 V or higher
q1-1 (-) - Service plug grip terminal 2 Power switch off 79 V or higher


CAUTION:

Do not allow the probes of the electrical tester to contact each other during this inspection.



d.

Install the No. 1 hybrid battery shield sub-assembly.


Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - HYBRID BATTERY JUNCTION BLOCK ASSEMBLY)

NG

9.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - HYBRID BATTERY JUNCTION BLOCK ASSEMBLY)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect connector I3 from the power management control ECU.


c.

Remove the No. 4 hybrid battery shield panel.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV RELAY ASSEMBLY>REMOVAL


d.
A284482C34
1.906,2.365 2.271,2.573 0.365,0.208 1.552,3.51 1.865,3.74 0.313,0.229 2.021,1.781 1.552,1.781 false 2.198,3.688 2.708,4.406 false 2.552,1.781 2.083,1.781 false 1.979,3.688 1.594,4.406 false 0.042,0.063 0.354,0.219 0.313,0.156 10 false *a 0.073,2.531 0.385,2.688 0.313,0.156 10 false *b 1.115,1.708 1.729,1.906 0.615,0.198 10 false SMRB 2.771,4.344 3.219,4.552 0.448,0.208 10 false SMRB 2.01,2.365 2.771,2.646 0.76,0.281 10 false I3 1.604,3.552 1.917,3.75 0.313,0.198 10 false O9 2.604,1.708 3.219,1.906 0.615,0.198 10 false SMRP 1.146,4.344 1.594,4.552 0.448,0.208 10 false SMRP
*a Rear view of wire harness connector
(to Power Management Control ECU)
*b Rear view of wire harness connector
(to Hybrid Battery Junction Block Assembly)


Disconnect the connector O9 that drives the system main relay of the hybrid battery junction block assembly.

HINT:

Before disconnecting the connector O9 that drives the system main relay of the hybrid battery junction block assembly, make sure that the connector is securely engaged.



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I3-4 (SMRB) - O9-1 (SMRB) Power switch off Below 1 Ω
I3-3 (SMRP) - O9-4 (SMRP) Power switch off Below 1 Ω



f.

Connect the hybrid battery junction block assembly connector.


g.

Install the No. 4 hybrid battery shield panel.


h.

Connect the power management control ECU connector.


Result:
Proceed to
OK
NG



OK

10.INSPECT HV BATTERY JUNCTION BLOCK ASSEMBLY (SMRB)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.INSPECT HV BATTERY JUNCTION BLOCK ASSEMBLY (SMRB)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the hybrid battery junction block assembly.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV RELAY ASSEMBLY>COMPONENTS


c.
A259731C34
0.865,0.344 1.281,0.583 0.417,0.24 0.313,2.271 0.667,2.51 0.354,0.24 2.927,0.792 3.344,1.031 0.417,0.24 1.385,2.552 1.573,2.792 false 1.188,2.542 0.875,2.75 false 0.458,0.656 0.844,0.823 false 2.74,1.219 2.99,1.51 false 0.969,0.385 1.469,0.677 0.5,0.292 10 false Q2 0.385,2.302 0.875,2.563 0.49,0.26 10 false O9 3.073,0.823 3.406,1.115 0.333,0.292 10 false A 0.646,2.792 1.281,3.115 0.635,0.323 10 false GND 1.385,2.823 2.104,3.188 0.719,0.365 10 false SMRB 0.052,0.031 0.396,0.198 0.344,0.167 10 false *a 3.031,1.458 3.365,1.75 0.333,0.292 10 false + 0.188,0.583 0.677,0.875 0.49,0.292 10 false CBI
*a Component without harness connected
(Hybrid Battery Junction Block Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Q2-1 (CBI) - A-1 (+) Auxiliary battery voltage is applied between terminals O9-1 (SMRB) and O9-2 (GND) Below 1 Ω



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O9-1 (SMRB) - O9-2 (GND) -40 to 80°C (-40 to 176°F) 25.0 to 59.0 Ω



e.

Install the hybrid battery junction block assembly.


Result:
Proceed to
OK
NG



OK

11.INSPECT HV BATTERY JUNCTION BLOCK ASSEMBLY (SMRP)

NG

REPLACE HV BATTERY JUNCTION BLOCK ASSEMBLY

11.INSPECT HV BATTERY JUNCTION BLOCK ASSEMBLY (SMRP)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the hybrid battery junction block assembly.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV RELAY ASSEMBLY>COMPONENTS


c.
A259731C35
0.125,0.979 0.542,1.219 0.417,0.24 0.313,2.271 0.667,2.51 0.354,0.24 2.917,1.479 3.333,1.719 0.417,0.24 1.25,2.552 1.385,2.802 false 0.917,2.542 0.74,2.813 false 0.458,0.656 0.76,0.99 false 2.677,1.542 2.927,1.833 false 0.208,0.99 0.708,1.281 0.5,0.292 10 false Q3 0.375,2.302 0.865,2.563 0.49,0.26 10 false O9 3.063,1.51 3.396,1.802 0.333,0.292 10 false q1 1.26,2.844 1.896,3.167 0.635,0.323 10 false GND 0.49,2.865 1.208,3.229 0.719,0.365 10 false SMRP 0.052,0.031 0.396,0.198 0.344,0.167 10 false *a 2.99,1.76 3.323,2.052 0.333,0.292 10 false - 0.188,0.583 0.677,0.875 0.49,0.292 10 false CEI
*a Component without harness connected
(Hybrid Battery Junction Block Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Q3-1 (CEI) - q1-1 (-) Auxiliary battery voltage is applied between terminals O9-4 (SMRP) and O9-2 (GND) 28.5 to 31.5 Ω



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O9-4 (SMRP) - O9-2 (GND) -40 to 80°C (-40 to 176°F) 112 to 274 Ω



e.

Install the hybrid battery junction block assembly.


Result:
Proceed to
OK
NG



OK

12.CHECK FOR INTERMITTENT PROBLEMS

NG

REPLACE HV BATTERY JUNCTION BLOCK ASSEMBLY

12.CHECK FOR INTERMITTENT PROBLEMS

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>CHECK FOR INTERMITTENT PROBLEMS

HINT:
·

Since 2 trip detection logic is used, the DTC detection condition must be met twice.

·

If DTC P3004-131 is output again after performing the inspection, replace the hybrid vehicle converter. If DTC P3004-131 is not output again, replace the hybrid battery junction block assembly.



Result:
Proceed to
OK
NG



OK

REPLACE HV BATTERY JUNCTION BLOCK ASSEMBLY

NG