1.REMOVE ROOF HEADLINING ASSEMBLY
2.REMOVE CHILD RESTRAINT SEAT ANCHOR BRACKET SUB-ASSEMBLY LH
73480
3.DISCONNECT REAR SEAT INNER WITH CENTER BELT ASSEMBLY LH
73360C
4.DISCONNECT REAR NO. 1 SEAT OUTER BELT ASSEMBLY RH
73370C
5.DISCONNECT REAR NO. 1 SEAT OUTER BELT ASSEMBLY LH
73373
6.REMOVE REAR SEAT SHOULDER BELT COVER
64330
7.REMOVE PACKAGE TRAY TRIM PANEL ASSEMBLY (w/o Rear Sunshade)
64330
8.REMOVE PACKAGE TRAY TRIM PANEL ASSEMBLY (w/ Rear Sunshade)
9.REMOVE CENTER STOP LIGHT SET (w/ Rear Sunshade)
64340B
10.REMOVE NO. 2 PACKAGE TRAY TRIM PANEL ASSEMBLY (w/ Rear Sunshade)
64811
11.REMOVE BACK WINDOW GLASS SUB-ASSEMBLY
Disconnect each connector.
| *1 | Protective Tape |
Apply protective tape to the area around the installation position of the back window glass on the vehicle body to prevent it from being scratched.
Apply protective tape to the vehicle body to prevent it from being scratched.
| *1 | Stopper |
| *2 | Piano Wire |
Pass a piano wire between the vehicle body and glass from the interior.
Tie both wire ends to wooden blocks or similar objects.
Cut off the adhesive by pulling the piano wire around the back window glass.
When separating the back window glass, take care not to damage the paint or interior and exterior ornaments.
| *1 | Matchmark |
Place matchmarks on the back window glass and vehicle body on the locations indicated in the illustration.
Matchmarks are not needed to be placed if the back window glass will not be reused.
Disconnect the back window glass stoppers.
| *A | 1-piece type | *B | 2-piece type |
| *1 | No. 1 Back Window Glass Stopper | *2 | No. 2 Back Window Glass Stopper |
There are No. 1 and No. 2 stoppers on the back window glass as shown in the illustration. Be careful not to damage the back window glass when cutting off the adhesive.
To prevent the back window glass from falling when performing this operation, be sure to hold the back window glass using suction cups.
Depending on the vehicle, either 1-piece or 2-piece type stoppers may be present.
Using suction cups, remove the back window glass sub-assembly.
Be careful not to drop the back window glass.
Leave as much adhesive on the vehicle body as possible when removing the back window glass.
56117A
12.REMOVE WINDOW GLASS ADHESIVE DAM
When reusing the back window glass:
| *A | Back Side |
Using a scraper, remove the window glass adhesive dam.
Be careful not to damage the back window glass.
Be sure to replace the window glass adhesive dam with a new one.
75573F
13.REMOVE BACK WINDOW OUTSIDE MOULDING
When reusing the back window glass:
| *A | Back Side |
Using a scraper, remove the back window outside moulding.
Be careful not to damage the back window glass.
Be sure to replace the back window outside moulding with a new one.
14.REMOVE NO. 1 BACK WINDOW GLASS STOPPER (for 1-piece Type)
When reusing the back window glass:
| *A | Back Side |
Using a scraper, remove the 2 No. 1 back window glass stoppers.
Be careful not to damage the back window glass.
Be sure to replace the No. 1 back window glass stoppers with new ones.
56116D
15.REMOVE NO. 2 BACK WINDOW GLASS STOPPER (for 2-piece Type)
When reusing the back window glass:
| *A | Back Side |
Using a scraper, remove the 2 No. 2 back window glass stoppers.
Be careful not to damage the back window glass.
Be sure to replace the No. 2 back window glass stoppers with new ones.
56115B
16.REMOVE NO. 1 BACK WINDOW GLASS STOPPER (for 2-piece Type)
Remove the 2 No. 1 back window glass stoppers.
Be sure to replace the No. 1 back window glass stoppers with new ones.
17.CLEAN BACK WINDOW GLASS
Using a scraper, remove any adhesive dam and adhesive residue from the back window glass.
Be careful not to damage the back window glass.
Clean the outer circumference of the back window glass with a non-residue solvent.
Do not touch the glass surface after cleaning it.
Be careful not to damage the glass.
Even if using new glass, clean it with a non-residue solvent.
18. CLEAN VEHICLE BODY
| *1 | Adhesive |
| *2 | Body |
Clean and shape the contact surface of the vehicle body.
Using a knife, cut away any rough adhesive on the contact surface of the vehicle body to ensure the appropriate surface shape.
Be careful not to damage the vehicle body.
Leave as much adhesive on the vehicle body as possible.
Clean the contact surface of the vehicle body with a piece of cloth saturated with cleaner.
Even if all the adhesive has been removed, clean the vehicle body.