Home › Vehicle Interior › INTERIOR PANELS / TRIM › ROOF HEADLINING › from 2015.04
RM2040EQ _58 Vehicle Interior _014732 INTERIOR PANELS / TRIM _0075129 ROOF HEADLINING A

INTERIOR PANELS / TRIM  ROOF HEADLINING  REMOVAL  


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the auxiliary battery negative (-) terminal. Therefore, make sure to read the disconnecting the cable from the auxiliary battery negative (-) terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 64718C 2.REMOVE LUGGAGE TRIM SERVICE HOLE COVER

Hide 3.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 67913 4.REMOVE FRONT DOOR SCUFF PLATE RH

a.
B396384N01
0.729,1.542 0.885,1.74 0.156,0.198 10 false A 2.302,0.688 2.458,0.885 0.156,0.198 10 false A 3.135,0.917 3.292,1.115 0.156,0.198 10 false B 1.406,2.656 1.563,2.854 0.156,0.198 10 true B 0.417,1.354 0.573,1.552 0.156,0.198 10 false 1 1.99,0.479 2.146,0.677 0.156,0.198 10 false 1 1.052,2.354 1.208,2.552 0.156,0.198 10 false 2 2.771,0.563 2.927,0.76 0.156,0.198 10 false 2 0.573,0.531 0.729,0.729 0.156,0.198 10 false C 2.656,1.875 2.813,2.073 0.156,0.198 10 false C

Disengage the 2 claws (A) in the direction indicated by the arrows (1) shown in the illustration.


b.

Disengage the 2 claws (B) in the direction indicated by the arrows (2) shown in the illustration.


c.

Disengage the 6 claws (C) to remove the front door scuff plate RH.


Hide 62111A 5.REMOVE COWL SIDE TRIM SUB-ASSEMBLY RH

a.
B286808

Remove the clip.


b.

Pull the cowl side trim sub-assembly RH as shown in the illustration to disengage the 2 clips and remove the cowl side trim sub-assembly RH.


Hide 62311B 6.REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH

a.

Remove the front door opening trim weatherstrip RH.


Hide 62211 7.REMOVE FRONT PILLAR GARNISH RH

a.
B287222C02
2.802,0.75 2.719,0.448 false 2.729,0.76 3.063,1.042 0.333,0.281 10 false *1
*1 Front Pillar Garnish Clip


Pull the upper part of the front pillar garnish RH toward the inside of the cabin and disengage the clip and front pillar garnish RH from the base of the front pillar garnish clip.

HINT:

Let the front pillar garnish RH hang from the front pillar garnish clip.



b.
B287223N04
1.313,1.479 1.646,1.677 0.333,0.198 10 false B 0.74,0.833 0.969,0.99 0.229,0.156 10 false A 0.99,0.146 1.281,0.365 0.292,0.219 10 false A

While pushing the tabs of the front pillar garnish clip in the direction indicated by the arrows (A) shown in the illustration, disengage the front pillar garnish clip.

NOTICE:

Disengage the front pillar garnish clip by hand. Using a tool may damage the front pillar garnish clip.



c.

Pull the front pillar garnish RH in the direction indicated by the arrow (B) shown in the illustration to disengage the 2 guides and remove the front pillar garnish RH.


d.
B287225C03
2.333,1 2.333,1.365 true 2.177,0.385 1.646,0.313 false 1.927,0.76 1.188,0.656 true 1.458,0.229 1.719,0.438 0.26,0.208 10 false *a 1,0.573 1.26,0.802 0.26,0.229 10 false *b 2.25,1.375 2.542,1.583 0.292,0.208 10 false *1
*1 Curtain Shield Airbag Assembly RH
*a Adhesive Tape
*b Protective Cover


Protect the curtain shield airbag assembly RH.

i.

Cover the curtain shield airbag assembly RH with a piece of cloth or nylon and secure the edges of the cover with tape as shown in the illustration.

NOTICE:

Cover the curtain shield airbag assembly RH with a protective cover as soon as the front pillar garnish RH is removed.




Hide 67914 8.REMOVE FRONT DOOR SCUFF PLATE LH

HINT:

Use the same procedure as for the RH side.


Hide 62112A 9.REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH

HINT:

Use the same procedure as for the RH side.


Hide 62312B 10.REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH

HINT:

Use the same procedure as for the RH side.


Hide 62212 11.REMOVE FRONT PILLAR GARNISH LH

HINT:

Use the same procedure as for the RH side.


Hide 12.REMOVE REAR SEAT CUSHION ASSEMBLY

Hide 72693 13.REMOVE REAR SEAT CUSHION LOCK HOOK

Hide 14.REMOVE REAR SEATBACK ASSEMBLY RH

Hide 64277C 15.REMOVE NO. 2 ROOM PARTITION COVER

Hide 16.REMOVE REAR SEATBACK ASSEMBLY LH

Hide 17.REMOVE REAR SIDE SEATBACK ASSEMBLY LH

Hide 18.REMOVE REAR SIDE SEATBACK ASSEMBLY RH

Hide 67917A 19.REMOVE REAR DOOR SCUFF PLATE RH

a.
B396385N01
2.854,0.708 3.01,0.906 0.156,0.198 10 false 1 3.135,0.927 3.292,1.125 0.156,0.198 10 false A 3.063,2.354 3.219,2.552 0.156,0.198 10 false B 2.76,2.01 2.917,2.208 0.156,0.198 10 false 2 2.188,2.75 2.344,2.948 0.156,0.198 10 false C 0.344,1.74 0.5,1.938 0.156,0.198 10 false C 1.115,0.844 1.271,1.042 0.156,0.198 10 false C 1.594,0.625 1.75,0.823 0.156,0.198 10 false C

Disengage the claw (A) in the direction indicated by the arrow (1) shown in the illustration.


b.

Disengage the claw (B) in the direction indicated by the arrow (2) shown in the illustration.


c.

Disengage the 4 claws (C) to remove the rear door scuff plate RH.

HINT:

Disengage the claws from the front side of the rear door scuff plate RH.



Hide 62331A 20.REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH

a.

Remove the rear door opening trim weatherstrip RH.


Hide 73233 21.REMOVE LAP BELT OUTER ANCHOR COVER (for RH Side)

Hide 73210 22.DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY RH

Hide 62413A 23.REMOVE CENTER PILLAR LOWER GARNISH RH

a.
B287226

Disengage the 2 claws and 3 clips, and remove the center pillar lower garnish RH.


Hide 62411B 24.REMOVE CENTER PILLAR UPPER GARNISH RH

a.
B287227

Remove the 2 screws.


b.

Disengage the clip.


c.

Pass the floor anchor of the front seat outer belt assembly RH through the center pillar upper garnish RH and remove the center pillar upper garnish RH.


Hide 62471A 25.REMOVE ROOF SIDE INNER GARNISH RH

a.
B287228

Disengage the 5 clips.


b.

Disengage the 2 guides and remove the roof side inner garnish RH.


Hide 67918A 26.REMOVE REAR DOOR SCUFF PLATE LH

HINT:

Use the same procedure as for the RH side.


Hide 62332A 27.REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH

HINT:

Use the same procedure as for the RH side.


Hide 73233 28.REMOVE LAP BELT OUTER ANCHOR COVER (for LH Side)

HINT:

Use the same procedure as for the RH side.


Hide 73220 29.DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY LH

HINT:

Use the same procedure as for the RH side.


Hide 62414A 30.REMOVE CENTER PILLAR LOWER GARNISH LH

HINT:

Use the same procedure as for the RH side.


Hide 62412B 31.REMOVE CENTER PILLAR UPPER GARNISH LH

HINT:

Use the same procedure as for the RH side.


Hide 62472A 32.REMOVE ROOF SIDE INNER GARNISH LH

HINT:

Use the same procedure as for the RH side.


Hide 33.REMOVE FRONT SEAT ASSEMBLY RH

Hide 34.REMOVE FRONT SEAT ASSEMBLY LH

HINT:

Use the same procedure as for the RH side.


Hide 35.REMOVE INSTRUMENT PANEL SAFETY PAD

Hide 89943 36.REMOVE RAIN SENSOR COVER (w/ Lane Departure Alert System)

Hide 86466C 37.REMOVE NO. 2 LANE DEPARTURE WARNING CAMERA COVER (w/ Lane Departure Alert System)

Hide 86466 38.REMOVE NO. 1 LANE DEPARTURE WARNING CAMERA COVER (w/ Lane Departure Alert System)

Hide 63650A 39.REMOVE ROOF CONSOLE BOX ASSEMBLY (w/o Sliding Roof)

Hide 63650A 40.REMOVE ROOF CONSOLE BOX ASSEMBLY (w/ Sliding Roof)

Hide 81240 41.REMOVE NO. 1 ROOM LIGHT ASSEMBLY (w/o Sliding Roof)

Hide 81360T 42.REMOVE SPOT LIGHT ASSEMBLY (w/ Sliding Roof)

Hide 74610A 43.REMOVE ASSIST GRIP SUB-ASSEMBLY (for RH Side)

a.
B287232C06
1.844,1.052 1.281,0.604 false 1.125,0.521 1.5,0.802 0.375,0.281 10 false *a
*a Protective Tape


Using a screwdriver, disengage the 4 claws and remove the 2 assist grip covers.

NOTICE:

Do not forcibly pry the assist grip covers to prevent them from being deformed.


HINT:

Tape the screwdriver tip before use.



b.
B287236

Disengage the 2 clips and remove the assist grip sub-assembly.


c.

Remove the 2 clips from the vehicle body.


Hide 74610A 44.REMOVE ASSIST GRIP SUB-ASSEMBLY (for LH Side)

HINT:

Use the same procedure as for the RH side.


Hide 74620C 45.REMOVE REAR ASSIST GRIP ASSEMBLY RH

a.
B287234C08
1.771,1 1.438,0.656 false 1.25,0.563 1.406,0.708 0.156,0.146 10 false *a
*a Protective Tape


Using a screwdriver, disengage the 4 claws and remove the 2 assist grip covers.

NOTICE:

Do not forcibly pry the assist grip covers to prevent them from being deformed.


HINT:

Tape the screwdriver tip before use.



b.
B287237

Disengage the 2 clips and remove the rear assist grip assembly RH.


c.

Remove the 2 clips from the vehicle body.


Hide 74630E 46.REMOVE REAR ASSIST GRIP ASSEMBLY LH

HINT:

Use the same procedure as for the RH side.


Hide 63318C 47.REMOVE SLIDING ROOF OPENING TRIM MOULDING (w/ Sliding Roof)

a.

Remove the sliding roof opening trim moulding.


Hide 74325 48.REMOVE VISOR BRACKET COVER (for RH Side)

a.
B287229

Using a moulding remover, disengage the 4 claws and remove the visor bracket cover.


Hide 74310 49.REMOVE VISOR ASSEMBLY RH

a.
B287231

Remove the 2 screws and visor assembly RH.


Hide 74325 50.REMOVE VISOR BRACKET COVER (for LH Side)

HINT:

Use the same procedure as for the RH side.


Hide 74320 51.REMOVE VISOR ASSEMBLY LH

HINT:

Use the same procedure as for the RH side.


Hide 74348 52.REMOVE VISOR HOLDER

a.
B211697E01
1.094,0.292 1.563,0.563 0.469,0.271 10 false 45°

Turn the visor holder approximately 45° and pull it out as shown in the illustration.


b.

Disengage the 2 claws and remove the visor holder.

HINT:

Use the same procedure for the other visor holder.



Hide 53.REMOVE ROOF HEADLINING ASSEMBLY (w/o Sliding Roof)

a.

w/ Lane Departure Alert System:

i.

Disconnect the connector from the inner rear view mirror.


ii.

Disconnect the connector from the rain sensor.


iii.

Disconnect the connector from the lane departure warning camera.



b.

Remove the bolt and disconnect the bracket from the front pillar RH.

B396413C01
5.24,4.208 5.615,4.448 0.375,0.24 12 false *A
*A w/ Digital Audio Broadcasting Antenna - -



c.

Disengage the 3 clamps from the front pillar RH.


d.

Disengage the 4 clamps from the front pillar LH.


e.

Disengage the 2 clamps and disconnect the connector from the rear pillar RH.


f.

w/ Digital Audio Broadcasting Antenna:

i.

Disengage the clamp and disconnect the connector from the rear pillar LH.



g.

Remove the 2 clips.


h.

Slide the roof headlining assembly to disengage the 2 clips as shown in the illustration.

HINT:

Leave the 2 clips in the vehicle.



i.
B279009

Remove the roof headlining assembly from the vehicle through the front passenger side door.

NOTICE:

Do not damage the roof headlining assembly or vehicle interior.



j.
B279104

Remove the 2 clips from the vehicle body as shown in the illustration.


Hide 54.REMOVE ROOF HEADLINING ASSEMBLY (w/ Sliding Roof)

a.

w/ Lane Departure Alert System:

i.

Disconnect the connector from the inner rear view mirror.


ii.

Disconnect the connector from the rain sensor.


iii.

Disconnect the connector from the lane departure warning camera.



b.

Disconnect the connector from the sliding roof drive gear assembly.

B396415C01
5.25,4.219 5.625,4.458 0.375,0.24 12 false *A
*A w/ Digital Audio Broadcasting Antenna - -



c.

Remove the bolt and disconnect the bracket from the front pillar RH.


d.

Disengage the 3 clamps from the front pillar RH.


e.

Disengage the 4 clamps from the front pillar LH.


f.

Disengage the 2 clamps and disconnect the connector from the rear pillar RH.


g.

w/ Digital Audio Broadcasting Antenna:

i.

Disengage the clamp and disconnect the connector from the rear pillar LH.



h.

Remove the 2 clips.


i.

Disengage the 2 fasteners.


j.

Slide the roof headlining assembly to disengage the 2 clips as shown in the illustration.

HINT:

Leave the 2 clips in the vehicle.



k.
B279010

Remove the roof headlining assembly from the vehicle through the front passenger side door.

NOTICE:

Do not damage the roof headlining assembly or vehicle interior.



l.
B279104

Remove the 2 clips from the vehicle body as shown in the illustration.