Home › Engine / Hybrid System › 2AR-FXE ENGINE CONTROL › SFI SYSTEM (w/o EGR System)

DTC    P2111    Throttle Actuator Control System - Stuck Open

DTC    P2112    Throttle Actuator Control System - Stuck Closed

for Preparation Click here


DESCRIPTION

The throttle actuator is operated by the ECM, and opens and closes the throttle valve using gears. The opening angle of the throttle valve is detected by the throttle position sensor, which is mounted on the throttle with motor body assembly. The throttle position sensor provides feedback to the ECM. This feedback allows the ECM to appropriately control the throttle actuator and monitor the throttle opening angle as the ECM responds to driver inputs.

HINT:
This Electronic Throttle Control System (ETCS) does not use a throttle cable.


DTC No.
DTC Detection Condition
Trouble Area
P2111
The ECM signals the throttle actuator to close, but the actuator is stuck (1 trip detection logic).
  1. Throttle actuator
  2. Throttle with motor body assembly
  3. Throttle valve
  4. Wire harness or connector
  5. ECM
P2112
The ECM signals the throttle actuator to open, but the actuator is stuck (1 trip detection logic).
  1. Throttle actuator
  2. Throttle with motor body assembly
  3. Throttle valve
  4. Wire harness or connector
  5. ECM

MONITOR DESCRIPTION

The ECM determines that there is a malfunction in the ETCS when the throttle valve remains at a fixed angle despite a high drive current from the ECM. The ECM illuminates the MIL and stores a DTC.

MONITOR STRATEGY


Required Sensors/Components
Throttle actuator (throttle with motor body assembly)
Frequency of Operation
Continuous

TYPICAL ENABLING CONDITIONS


All 
Throttle actuator
On
Throttle actuator duty calculation
Executing
Throttle position sensor fail
Not detected
Throttle actuator current-cut operation
Not executing
Throttle actuator power supply
4 V or higher
Throttle actuator fail
Not detected

P2111: Throttle Actuator Stuck Open 
Both of following conditions are met:
-
Throttle actuator current
2 A or higher
Duty cycle to close throttle
80% or higher

P2112: Throttle Actuator Stuck Closed 
Both of the following conditions are met:
-
Throttle actuator current
2 A or higher
Duty cycle to open throttle
80% or more

TYPICAL MALFUNCTION THRESHOLDS


P2111: Throttle Actuator Stuck Open 
Throttle position sensor voltage
No change

P2112: Throttle Actuator Stuck Closed 
Throttle position sensor voltage
No change

CONFIRMATION DRIVING PATTERN


A199314E07

  1. Connect the intelligent tester to the DLC3.
  2. Turn the power switch on (IG) and turn the tester on.
  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  4. Turn the power switch off and wait for at least 30 seconds.
  5. Turn the power switch on (IG) and turn the tester on [A].
  6. Put the engine in inspection mode (maintenance mode) (Click here).
  7. Start the engine and fully depress and release the accelerator pedal quickly (to fully open and close the throttle valve).
  8. Enter the following menus: Powertrain / Engine and ECT / DTC [B].
  9. Read the pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  10. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  11. Input the DTC: P2111 or P2112.
  12. Check the DTC judgment result.

    Tester Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.
    3. If the judgment result shows INCOMPLETE or N/A, perform steps [A] and [B] again and, if necessary, drive the vehicle for period of time.


FAIL-SAFE

When either of these DTCs or other DTCs relating to Electronic Throttle Control System (ETCS) malfunctions are stored, the ECM enters fail-safe mode. During fail-safe mode, the ECM cuts the current to the throttle actuator, and the throttle valve is returned to a 5.5° throttle angle by the return spring. The ECM stops the engine and the vehicle can be driven using solely the hybrid system. If the accelerator pedal is depressed firmly and gently, the vehicle can be driven slowly.
Fail-safe mode continues until a pass condition is detected, and the power switch is then turned off.

WIRING DIAGRAM

Refer to DTC P2102 .

INSPECTION PROCEDURE

HINT:
  1. Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
  2. Refer to "Data List / Active Test" [Throttle Position Command, Throttle Position No. 1, Throttle Motor Current, Throttle Motor Duty (Open), Throttle Motor Duty (Close)] (Click here).

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P2111 OR P2112)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.

    Result 
    Result
    Proceed to
    DTC P2111 or P2112 is output
    A
    DTC P2111 or P2112 and other DTCs are output
    B

    HINT:
    If any DTCs other than P2111 or P2112 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART (Click here)
A


2.INSPECT THROTTLE WITH MOTOR BODY ASSEMBLY (VISUALLY CHECK THROTTLE VALVE)
  1. Check for contamination between the throttle valve and housing. If necessary, clean the throttle with motor body assembly. Also check that the throttle valve moves smoothly.

    OK:
    Throttle valve is not contaminated with foreign objects and moves smoothly.

    HINT:
    Perform "Inspection After Repair" after cleaning the throttle with motor body assembly (Click here).



NG
Go to step 5
OK


3.READ VALUE USING INTELLIGENT TESTER (THROTTLE POSITION)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the tester on.

  1. Clear the DTCs (Click here).

  1. Turn the power switch off and wait for at least 30 seconds.

  1. Turn the power switch on (IG) and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Throttle Position No. 1, Throttle Position No. 2 and Throttle Position Command.

  1. Read the values displayed on the tester while wiggling the ECM wire harness.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.

    Result 
    Result
    Proceed to
    Value in Data List changes when wire harness is wiggled, or DTC is output
    A
    Other than above
    B



B
Go to step 6
A


4.REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - THROTTLE WITH MOTOR BODY ASSEMBLY)
  1. As the DTC was stored due to a change in the contact resistance of the connector, repair or replace the wire harness or connector (Click here).


NEXT

END 

5.REPLACE THROTTLE WITH MOTOR BODY ASSEMBLY
  1. Replace the throttle with motor body assembly (Click here).

    HINT:
    Perform "Inspection After Repair" after replacing the throttle with motor body assembly (Click here).


NEXT


6.CHECK WHETHER DTC OUTPUT RECURS (DTC P2111 OR P2112)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the tester on.

  1. Clear the DTCs (Click here).

  1. Turn the power switch off and wait for at least 30 seconds.

  1. Turn the power switch on (IG).

  1. Turn the tester on.

  1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.

    Result 
    Result
    Proceed to
    DTC is not output
    A
    DTC P2111 or P2112 is output
    B



B
REPLACE ECM (Click here)
A

END