DTC P2111 Throttle Actuator Control System - Stuck Open |
DTC P2112 Throttle Actuator Control System - Stuck Closed |
| DTC No. | DTC Detection Condition | Trouble Area |
| P2111 | The ECM signals the throttle actuator to close, but the actuator is stuck (1 trip detection logic). |
|
| P2112 | The ECM signals the throttle actuator to open, but the actuator is stuck (1 trip detection logic). |
|
| Required Sensors/Components | Throttle actuator (throttle with motor body assembly) |
| Frequency of Operation | Continuous |
| Throttle actuator | On |
| Throttle actuator duty calculation | Executing |
| Throttle position sensor fail | Not detected |
| Throttle actuator current-cut operation | Not executing |
| Throttle actuator power supply | 4 V or higher |
| Throttle actuator fail | Not detected |
| Both of following conditions are met: | - |
| Throttle actuator current | 2 A or higher |
| Duty cycle to close throttle | 80% or higher |
| Both of the following conditions are met: | - |
| Throttle actuator current | 2 A or higher |
| Duty cycle to open throttle | 80% or more |
| Throttle position sensor voltage | No change |
| Throttle position sensor voltage | No change |

| GTS Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|
| 1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P2111 OR P2112) |
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
| DTC P2111 or P2112 is output | A |
| DTC P2111 or P2112 and other DTCs are output | B |
|
| ||||
| A | |
| 2.INSPECT THROTTLE WITH MOTOR BODY ASSEMBLY (VISUALLY CHECK THROTTLE VALVE) |
Check for contamination between the throttle valve and housing. If necessary, clean the throttle with motor body assembly. Also check that the throttle valve moves smoothly.
|
| ||||
| OK | |
| 3.READ VALUE USING GTS (THROTTLE POSITION) |
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Clear the DTCs (Click here).
Turn the power switch off and wait for at least 30 seconds.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Throttle Position No. 1, Throttle Position No. 2 and Throttle Position Command.
Read the values displayed on the GTS while wiggling the ECM wire harness.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
| Value in Data List changes when wire harness is wiggled, or DTC is output | A |
| Other than above | B |
|
| ||||
| A | |
| 4.REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - THROTTLE WITH MOTOR BODY ASSEMBLY) |
As the DTC was stored due to a change in the contact resistance of the connector, repair or replace the wire harness or connector (Click here).
| NEXT | ||
| ||
| 5.REPLACE THROTTLE WITH MOTOR BODY ASSEMBLY |
Replace the throttle with motor body assembly (Click here).
| NEXT | |
| 6.CHECK WHETHER DTC OUTPUT RECURS (DTC P2111 OR P2112) |
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Clear the DTCs (Click here).
Turn the power switch off and wait for at least 30 seconds.
Turn the power switch on (IG).
Turn the GTS on.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
| DTCs are not output | A |
| DTC P2111 or P2112 is output | B |
|
| ||||
| A | ||
| ||