DTC P2119 Throttle Actuator Control Throttle Body Range / Performance |
| DTC No. | DTC Detection Condition | Trouble Area |
| P2119 | The throttle valve opening angle continues to vary greatly from the target opening angle (1 trip detection logic). |
|
| Required Sensors/Components | Throttle actuator (throttle with motor body assembly) |
| Frequency of Operation | Continuous |
| Throttle actuator | On |
| Throttle actuator duty calculation | Executing |
| Throttle position sensor fail | Not detected |
| Throttle actuator current-cut operation | Not executing |
| Throttle actuator power supply | 4 V or higher |
| Throttle actuator fail | Not detected |
| Either of the following conditions is met | 1 or 2 |
| 1. Difference between commanded closed throttle position and current closed throttle position | 0.3 V or higher |
| 2. Difference between commanded open throttle position and current open throttle position | 0.3 V or higher |

| Tester Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|
| 1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P2119) |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
| Result | Proceed to |
| DTC P2119 is output | A |
| DTC P2119 and other DTCs are output | B |
|
| ||||
| A | |
| 2.READ VALUE USING INTELLIGENT TESTER (THROTTLE POSITION) |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the tester on.
Clear the DTCs (Click here).
Turn the power switch off and wait for at least 30 seconds.
Turn the power switch on (IG) and turn the tester on.
Put the engine in inspection mode (maintenance mode) (Click here).
Start the engine.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Throttle Position No. 1 and Throttle Position Command.
Read the values displayed on the tester while fully depressing and releasing the accelerator pedal quickly.
| Result | Proceed to |
| Throttle Position No. 1 does not change | A |
| Throttle Position No. 1 changes even a little | B |
|
| ||||
| A | |
| 3.INSPECT THROTTLE WITH MOTOR BODY ASSEMBLY (RESISTANCE OF THROTTLE ACTUATOR) |
Inspect the throttle with motor body assembly (Click here).
|
| ||||
| OK | |
| 4.INSPECT THROTTLE WITH MOTOR BODY ASSEMBLY (VISUALLY CHECK THROTTLE VALVE) |
Check for contamination between the throttle valve and housing. If necessary, clean the throttle with motor body assembly. Also, check that the throttle valve moves smoothly.
|
| ||||
| OK | |
| 5.READ VALUE USING INTELLIGENT TESTER (THROTTLE POSITION) |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the tester on.
Clear the DTCs (Click here).
Turn the power switch off and wait for at least 30 seconds.
Turn the power switch on (IG) and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Throttle Position No. 1, Throttle Position No. 2 and Throttle Position Command.
Read the values displayed on the tester while wiggling the ECM wire harness.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
| Result | Proceed to |
| Value in Data List changes when wire harness is wiggled, or DTC is output | A |
| Other than above | B |
|
| ||||
| A | |
| 6.REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - THROTTLE WITH MOTOR BODY ASSEMBLY) |
As the DTC was stored due to a change in the contact resistance of the connector, repair or replace the wire harness or connector (Click here).
| NEXT | ||
| ||
| 7.REPLACE THROTTLE WITH MOTOR BODY ASSEMBLY |
Replace the throttle with motor body assembly (Click here).
| NEXT | |
| 8.CHECK WHETHER DTC OUTPUT RECURS (DTC P2119) |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the tester on.
Clear the DTCs (Click here).
Turn the power switch off and wait for at least 30 seconds.
Turn the power switch on (IG).
Turn the tester on.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
| Result | Proceed to |
| DTC is not output | A |
| DTC P2119 is output | B |
|
| ||||
| A | ||
| ||