Home › Engine / Hybrid System › 2AR-FXE ENGINE CONTROL › SFI SYSTEM (w/ EGR System)

DTC    P0560    System Voltage

for Preparation Click here


MONITOR DESCRIPTION

The auxiliary battery supplies electricity to the ECM even when the power switch is off. This power allows the ECM to store data such as DTC history, freeze frame data and fuel trim values. If the auxiliary battery voltage falls below a minimum level, the memory is cleared and the ECM determines that there is a malfunction in the power supply circuit. When the engine is next started, the ECM illuminates the MIL and stores the DTC.

DTC No.
DTC Detection Condition
Trouble Area
P0560
An open in the ECM back up power source circuit (1 trip detection logic).
  1. Open in back up power source circuit
  2. Auxiliary battery
  3. Auxiliary battery terminals
  4. ECM

HINT:
If DTC P0560 is stored, the ECM does not store other DTCs or the data stored in the ECM is partly cleared.


MONITOR STRATEGY


Required Sensors/Components
ECM
Frequency of Operation
Continuous

TYPICAL MALFUNCTION THRESHOLDS


Both of the following conditions are met
-
Auxiliary battery voltage
Less than 3.5 V
Stand-by RAM
Initialized

CONFIRMATION DRIVING PATTERN

  1. Connect the GTS to the DLC3.
  2. Turn the power switch on (IG).
  3. Turn the GTS on.
  4. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  5. Turn the power switch off and wait for at least 30 seconds.
  6. Turn the power switch on (IG).
  7. Turn the GTS on.
  8. Wait 5 seconds or more.
  9. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
  10. Read the pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  11. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  12. Input the DTC: P0560.
  13. Check the DTC judgment result.

    GTS Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.
    3. If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.


WIRING DIAGRAM


A315307E01


INSPECTION PROCEDURE

NOTICE:
  1. Inspect the fuses for circuits related to this system before performing the following inspection procedure.
  2. After turning power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (Click here).

HINT:
Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.INSPECT AUXILIARY BATTERY
  1. Inspect that the auxiliary battery is not depleted .

    OK:
    Auxiliary battery is not depleted



NG
REPLACE AUXILIARY BATTERY
OK


2.CHECK AUXILIARY BATTERY TERMINAL
  1. Check that the auxiliary battery terminals are not loose or corroded.

    OK:
    Auxiliary battery terminals are not loose or corroded



NG
REPAIR OR REPLACE AUXILIARY BATTERY TERMINAL
OK


3.CHECK TERMINAL VOLTAGE (POWER SOURCE OF ECM)


    A255690E08
  1. Disconnect the ECM connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    A25-1 (BATT) - Body ground
    Power switch off
    11 to 16 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to ECM)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (AUXILIARY BATTERY - ECM)
OK


4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0560)
  1. Connect the GTS to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the GTS on.

  1. Clear the DTCs (Click here).

  1. Turn the power switch off and wait for at least 30 seconds.

  1. Turn the power switch on (IG).

  1. Turn the GTS on.

  1. Wait 5 seconds or more.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs.

    Result 
    Result
    Proceed to
    DTC P0560 is output
    A
    DTCs are not output
    B



B
CHECK FOR INTERMITTENT PROBLEMS (Click here)
A

REPLACE ECM (Click here)