POWER DOOR LOCK CONTROL SYSTEM > All Doors LOCK/UNLOCK Functions do not Operate Via Door Control Switch or Door Key Cylinder |


| 1.CHECK DOOR LOCK OPERATION |
Check door lock operation (Click here).
| Result | Proceed to |
| All doors cannot be locked through multiplex network master switch | A |
| All doors cannot be locked through driver door key cylinder | B |
|
| ||||
| A | |
| 2.CHECK DTC OUTPUT (LIN COMMUNICATION SYSTEM) |
Clear the DTC (Click here).
Recheck for DTCs.
|
| ||||
| OK | |
| 3.REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY |
Replace the multiplex network master switch assembly (Click here).
| NEXT | |
| 4.CHECK DOOR LOCK OPERATION |
Check that all doors can be locked and unlocked by using the multiplex network master switch assembly (Click here).
|
| ||||
| OK | ||
| ||
| 5.READ VALUE USING INTELLIGENT TESTER (DOOR KEY-LINKED LOCK AND UNLOCK SWITCH) |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body / Main Body / Data List.
Read the Data List according to the display on the intelligent tester.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Door Key SW-Lock | Driver door key-linked lock/unlock switch lock signal/ON or OFF | ON: Driver door key cylinder turned to lock position OFF: Driver door key cylinder not turned to lock position | - |
| D Door Key SW-UL | Driver door key-linked lock/unlock switch unlock signal/ON or OFF | ON: Driver door key cylinder turned to unlock position OFF: Driver door key cylinder not turned to unlock position | - |
|
| ||||
| OK | ||
| ||
| 6.INSPECT FRONT DOOR LOCK WITH MOTOR ASSEMBLY (for DRIVER DOOR) |
Remove the front door lock with motor assembly (for driver door) (Click here).
for LHD
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 9 (L) - 7 (E) | Locked | Below 1 Ω |
| 9 (L) - 7 (E) | off | 10 kΩ or higher |
| 10 (UL) - 7 (E) | Unlocked | Below 1 Ω |
| 10 (UL) - 7 (E) | off | 10 kΩ or higher |
| *a | Component without harness connected (Front Door Lock with Motor Assembly LH) |
| *b | Unlock |
| *c | Lock |
for RHD
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 6 (L) - 8 (E) | Locked | Below 1 Ω |
| 6 (L) - 8 (E) | off | 10 kΩ or higher |
| 5 (UL) - 8 (E) | Unlocked | Below 1 Ω |
| 5 (UL) - 8 (E) | off | 10 kΩ or higher |
| *a | Component without harness connected (Front Door Lock with Motor Assembly RH) |
| *b | Unlock |
| *c | Lock |
|
| ||||
| OK | |
| 7.CHECK HARNESS AND CONNECTOR (FRONT DOOR LOCK WITH MOTOR ASSEMBLY - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)) |
Disconnect the I13 main body ECU (multiplex network body ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| K1-9 (L) - I13-11 (L2) | Always | Below 1 Ω |
| K1-10 (UL) - I13-24 (UL3) | Always | Below 1 Ω |
| K1-7 (E) - Body ground | Always | Below 1 Ω |
| I13-11 (L2) - Body ground | Always | 10 kΩ or higher |
| I13-24 (UL3) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| J1-6 (L) - I13-11 (L2) | Always | Below 1 Ω |
| J1-5 (UL) - I13-24 (UL3) | Always | Below 1 Ω |
| J1-8 (E) - Body ground | Always | Below 1 Ω |
| I13-11 (L2) - Body ground | Always | 10 kΩ or higher |
| I13-24 (UL3) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||