Home › Vehicle Exterior › SLIDING ROOF / CONVERTIBLE › SLIDING ROOF SYSTEM

SLIDING ROOF SYSTEM > Sliding Roof does not Move by Operating Sliding Roof Control Switch

for Preparation Click here


DESCRIPTION

The sliding roof ECU (sliding roof drive gear sub-assembly) receives slide and tilt signals when the sliding roof switch is operated and drives its built-in motor.

WIRING DIAGRAM


B278886E08


INSPECTION PROCEDURE

NOTICE:
  1. Inspect the fuses for circuits related to this system before performing the following inspection procedure.
  2. When the sliding roof ECU (sliding roof drive gear sub-assembly) is removed and reinstalled or replaced, the sliding roof ECU (sliding roof drive gear sub-assembly) must be initialized (Click here).
  3. The sliding roof system uses the LIN communication system. First, confirm that there are no malfunctions in the LIN communication system. Refer to the How to Proceed with Troubleshooting procedure (Click here).
  4. When a sliding roof ECU (sliding roof drive gear sub-assembly) DTC is output, first perform troubleshooting for the sliding roof ECU (sliding roof drive gear sub-assembly) DTC.

1.READ VALUE USING INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Sliding Roof / Data List.

  1. Read the Data List according to the display on the intelligent tester.


Sliding Roof (Sliding Roof ECU (Sliding Roof Drive Gear Sub-assembly)) 
Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Open Switch
OPEN switch signal/ON or OFF
ON: OPEN switch pressed
OFF: OPEN switch not pressed
-
Close Switch
CLOSE switch signal/ON or OFF
ON: CLOSE switch pressed
OFF: CLOSE switch not pressed
-
Up Switch
UP switch signal/ON or OFF
ON: UP switch pressed
OFF: UP switch not pressed
-
Down Switch
DOWN switch signal/ON or OFF
ON: DOWN switch pressed
OFF: DOWN switch not pressed
-

OK:
The intelligent tester display changes according to switch operation as shown in the table.



NG
Go to step 3
OK


2.CHECK HARNESS AND CONNECTOR (SLIDING ROOF ECU - AUXILIARY BATTERY AND BODY GROUND)
  1. Disconnect the S4 sliding roof ECU (sliding roof drive gear sub-assembly) connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    S4-8 (B) - Body ground
    Power switch off
    11 to 14 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    S4-12 (E) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY) (Click here)  

3.INSPECT SLIDING ROOF SWITCH (ROOF CONSOLE BOX ASSEMBLY)


    B270995E01
  1. Remove the sliding roof switch (roof console box assembly) (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    5 (UP) - 1 (GND)
    UP switch is pressed
    Below 1 Ω
    5 (UP) - 1 (GND)
    UP switch is not pressed
    10 kΩ or higher
    4 (DOWN) - 1 (GND)
    DOWN switch is pressed
    Below 1 Ω
    4 (DOWN) - 1 (GND)
    DOWN switch is not pressed
    10 kΩ or higher
    3 (OPN) - 1 (GND)
    OPEN switch is pressed
    Below 1 Ω
    3 (OPN) - 1 (GND)
    OPEN switch is not pressed
    10 kΩ or higher
    2 (CLS) - 1 (GND)
    CLOSE switch is pressed
    Below 1 Ω
    2 (CLS) - 1 (GND)
    CLOSE switch is not pressed
    10 kΩ or higher

    Text in Illustration 
    *a
    Component without harness connected
    (Sliding Roof Switch (Roof Console Box Assembly))



NG
REPLACE SLIDING ROOF SWITCH (ROOF CONSOLE BOX ASSEMBLY) (Click here)
OK


4.CHECK HARNESS AND CONNECTOR (SLIDING ROOF ECU - SLIDING ROOF SWITCH AND BODY GROUND)
  1. Disconnect the S7 sliding roof switch (roof console box assembly) connector.

  1. Disconnect the S4 sliding roof ECU (sliding roof drive gear sub-assembly) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    S4-5 (CLS) - S7-2 (CLS)
    Always
    Below 1 Ω
    S4-5 (CLS) - Body ground
    Always
    10 kΩ or higher
    S4-7 (OPN) - S7-3 (OPN)
    Always
    Below 1 Ω
    S4-7 (OPN) - Body ground
    Always
    10 kΩ or higher
    S4-6 (DWN) - S7-4 (DOWN)
    Always
    Below 1 Ω
    S4-6 (DWN) - Body ground
    Always
    10 kΩ or higher
    S4-4 (UP) - S7-5 (UP)
    Always
    Below 1 Ω
    S4-4 (UP) - Body ground
    Always
    10 kΩ or higher
    S7-1 (GND) - Body ground
    Always
    Below 1 Ω
    S4-12 (E) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY) (Click here)