Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM

CAN COMMUNICATION SYSTEM > Check CAN Bus Lines for Short Circuit (RHD Models)

for Preparation Click here


DESCRIPTION

There may be a short circuit between the V bus main lines and/or CAN branch lines when the resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is below 54 Ω.

Symptom
Trouble Area
Resistance between terminals 6 (CANH) and 14 (CANL) of DLC3 is below 54 Ω.
  1. Short in CAN main bus line
  2. Short in CAN branch line
  3. Power management control ECU
  4. ECM
  5. Main body ECU (Multiplex network body ECU)
  6. Combination meter assembly
  7. Brake booster with master cylinder assembly (Skid control ECU)
  8. Steering sensor
  9. Clearance warning ECU assembly
  10. Power steering ECU assembly
  11. Airbag sensor assembly
  12. Air conditioning amplifier assembly
  13. Smart key ECU assembly (Certification ECU)
  14. Radio and display receiver assembly
  15. CAN junction LH connector
  16. CAN junction RH connector

WIRING DIAGRAM


C273084E02


C248241E04


INSPECTION PROCEDURE

NOTICE:
  1. Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
  2. After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (Click here).
  3. Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (Click here).
  4. After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.
  5. DTC check procedure: Turn the power switch on (IG), turn the cruise control system on using the cruise control main switch (ON/OFF switch), wait at least 60 seconds, and then drive the vehicle at a speed of 20 km/h (12 mph) or more for at least 11 seconds.
  6. After the repair, perform Communication Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed (Click here).

HINT:
  1. Operating the power switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.
  2. Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.
  3. Connectors that connect to the CAN junction connector can be distinguished by the color of their CAN bus lines. When the connectors have been disconnected from the CAN junction connector, reconnecting the connectors to non-original positions on the CAN junction connector does not affect system performance. However, it is preferred to reconnect the connectors to their original positions to avoid negative effects on the wiring such as tension on the wire harnesses, and to make future maintenance easier.

1.CHECK FOR SHORT IN CAN BUS LINES (DLC3 BRANCH LINE)
  1. Disconnect the cable from the negative (-) auxiliary battery terminal.



    C248242E01
  1. Disconnect the I96 CAN junction RH connector.
    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to CAN Junction RH Connector)
    *b
    to DLC3

    NOTICE:
    1. Before disconnecting the connector, make a note of where it is connected.
    2. Reconnect the connector to its original position.



    C210421E47
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I39-6 (CANH) - I39-14 (CANL)
    Cable disconnected from negative (-) auxiliary battery terminal
    1 MΩ or higher

    Text in Illustration 
    *1
    DLC3



NG
REPAIR OR REPLACE CAN BRANCH LINE CONNECTED TO DLC3
OK


2.CHECK FOR SHORT IN CAN BUS LINES (BRANCH LINE)
  1. Reconnect the I96 CAN junction RH connector.



    C210421E47
  1. Connect the probes of an ohmmeter to terminals 6 (CANH) and 14 (CANL) of the DLC3.
    Text in Illustration 
    *1
    DLC3



  1. While observing the resistance value shown on the tester, disconnect the I95, I102, I103, I100, I107 and I109 CAN junction LH connectors or I97, I106, I110 and I111 CAN junction RH connectors one by one until the resistance becomes normal (between 54 and 69 Ω).

    HINT:
    Disconnect the branch line connectors other than those of the DLC3.


    C273085E01


    Text in Illustration 
    *1
    Power Management Control ECU
    *2
    Main Body ECU (Multiplex Network Body ECU)
    *3
    Air Conditioning Amplifier Assembly
    *4
    Airbag Sensor Assembly
    *5
    Power Steering ECU Assembly
    *6
    ECM
    *7
    Radio and Display Receiver Assembly
    *8
    Combination Meter Assembly
    *9
    DLC3
    *10
    Smart Key ECU Assembly (Certification ECU)
    *11
    Brake Booster with Master Cylinder Assembly (Skid Control ECU)
    *12
    Steering Sensor
    *13
    Clearance Warning ECU Assembly
    *14
    CAN Junction RH Connector
    *15
    CAN Junction LH Connector
    -
    -

    C241464E04


    Text in Illustration 
    *a
    Component without harness connected
    (CAN Junction LH Connector)
    -
    -

    Wiring Color 
    CAN Junction LH Connector Side
    Code
    Color (CANH Side)
    Color (CANL Side)
    CAN main bus line (bus line connecting CAN junction LH connector and CAN junction RH connector)
    I93
    B
    W
    Radio and display receiver assembly
    I107
    R
    W
    ECM
    I104
    G
    W
    Power steering ECU assembly
    I100
    L
    W
    Airbag sensor assembly
    I103
    Y
    W
    Air conditioning amplifier assembly
    I102
    V
    W
    Main body ECU (Multiplex network body ECU)
    I95
    P
    W
    Power management control ECU
    I109
    BE
    W

    C273083E02


    Text in Illustration 
    *a
    Component without harness connected
    (CAN Junction RH Connector)
    -
    -

    Wiring Color 
    CAN Junction RH Connector Side
    Code
    Color (CANH Side)
    Color (CANL Side)
    Clearance warning ECU assembly
    I111
    P
    W
    Steering sensor
    I97
    V
    W
    Brake booster with master cylinder assembly (Skid control ECU)
    I110
    Y
    W
    Smart key ECU assembly (Certification ECU)
    I106
    L
    W
    DLC3
    I96
    G
    W
    Combination meter assembly
    I94
    R
    W
    CAN main bus line (bus line connecting CAN junction LH connector and CAN junction RH connector)
    I101
    B
    W

    NOTICE:
    Do not reconnect the disconnected connectors until this inspection is complete because there may be a short in 2 or more branch lines.


    Result:

    Symptom
    Proceed to
    The resistance is still below 54 Ω when all the specified connectors are disconnected. (There are no shorts between a pair of branch lines.)
    A
    The resistance becomes normal (between 54 and 69 Ω) when a connector is disconnected. (There is a short between one or more pairs of branch lines.)
    B

  1. When there is a short in one or more of the branch lines:

    1. Reconnect all of the connectors to the CAN junction connector, except for the one that was disconnected last (the short-circuited bus line). Check that the resistance shown on the tester is normal (between 54 and 69 Ω) to confirm that there is a short in the one branch line only.

      HINT:
      1. Connectors that connect to the CAN junction connector can be distinguished by the color of their CAN bus lines.
      2. Reconnecting the connectors to non-original positions on the CAN junction connector does not affect system performance. However, it is preferred to reconnect the connectors to their original positions to avoid negative effects on the wiring such as tension on the wire harnesses, and to make future maintenance easier.



B
Go to step 7
A


3.CHECK FOR SHORT IN CAN BUS LINES (COMBINATION METER ASSEMBLY MAIN BUS LINE)


    C248237E01
  1. Disconnect the I94 CAN junction RH connector.
    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to CAN Junction RH Connector)
    *b
    to Combination Meter Assembly

    NOTICE:
    1. Before disconnecting the connector, make a note of where it is connected.
    2. Reconnect the connector to its original position.



    C210421E47
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I39-6 (CANH) - I39-14 (CANL)
    Cable disconnected from negative (-) auxiliary battery terminal
    108 to 132 Ω

    Text in Illustration 
    *1
    DLC3

    Result:

    Symptom
    Proceed to
    The resistance is still below 54 Ω when the combination meter assembly connector is disconnected. (There are no shorts in the combination meter assembly or between its main bus lines.)
    A
    The resistance falls within the specified range (between 108 and 132 Ω) (the other terminating resistor is normal) when the combination meter assembly connector is disconnected. (There is a short in the combination meter assembly or between its main bus lines.)
    B



B
Go to step 8
A


4.CHECK FOR SHORT IN CAN BUS LINES (ECM MAIN BUS LINE)


    C248246E01
  1. Disconnect the I104 CAN junction LH connector.
    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to CAN Junction LH Connector)
    *b
    to ECM

    NOTICE:
    1. Before disconnecting the connector, make a note of where it is connected.
    2. Reconnect the connector to its original position.



    C210421E47
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I39-6 (CANH) - I39-14 (CANL)
    Cable disconnected from negative (-) auxiliary battery terminal
    1 MΩ or higher

    Text in Illustration 
    *1
    DLC3

    HINT:
    Measure the resistance with the combination meter assembly main bus line connector (I94) disconnected.


    Result:

    Symptom
    Proceed to
    The resistance is still below 1 MΩ when the ECM connector is disconnected. (There are no shorts in the ECM or between its main bus lines.)
    A
    The resistance becomes 1 MΩ or higher when the ECM connector is disconnected. (There is a short in the ECM or between its main bus lines.)
    B



B
Go to step 9
A


5.CHECK FOR SHORT IN CAN BUS LINES (CAN J/C RH)


    C248239E02
  1. Disconnect the I101 CAN junction RH connector.
    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to CAN Junction RH Connector)
    *b
    to CAN Junction LH Connector

    NOTICE:
    1. Before disconnecting the connector, make a note of where it is connected.
    2. Reconnect the connector to its original position.



    C210421E47
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I39-6 (CANH) - I39-14 (CANL)
    Cable disconnected from negative (-) auxiliary battery terminal
    1 MΩ or higher

    Text in Illustration 
    *1
    DLC3



NG
REPLACE CAN JUNCTION RH CONNECTOR
OK


6.CHECK FOR SHORT IN CAN BUS LINES (CAN J/C LH - CAN J/C RH)
  1. Reconnect the I101 CAN junction RH connector.



    C248247E01
  1. Disconnect the I93 CAN junction LH connector.
    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to CAN Junction LH Connector)
    *b
    to CAN Junction RH Connector

    NOTICE:
    1. Before disconnecting the connector, make a note of where it is connected.
    2. Reconnect the connector to its original position.



    C210421E47
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I39-6 (CANH) - I39-14 (CANL)
    Cable disconnected from negative (-) auxiliary battery terminal
    1 MΩ or higher

Text in Illustration 
*1
DLC3


NG
REPAIR OR REPLACE CAN MAIN BUS LINES (CAN J/C LH - CAN J/C RH)
OK

REPLACE CAN JUNCTION LH CONNECTOR 

7.CHECK FOR SHORT IN CAN BUS LINES (ECU, SENSOR)
  1. Reconnect the connector for the short-circuited branch line to the CAN junction connector (the connector that caused the bus line resistance to become normal (between 54 and 69 Ω) when it was disconnected).

  1. Disconnect the connector that includes the DLC3 connected CAN lines (such as CANH and CANL) from the ECU or sensor to which the short-circuited branch line is connected (Click here).



    C210421E47
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I39-6 (CANH) - I39-14 (CANL)
    Cable disconnected from negative (-) auxiliary battery terminal
    54 to 69 Ω

    Text in Illustration 
    *1
    DLC3

    HINT:
    If the resistance becomes normal (between 54 and 69 Ω) when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.



NG
REPAIR OR REPLACE CORRESPONDING ECU OR SENSOR BRANCH LINES OR CONNECTOR
OK

REPLACE CORRESPONDING ECU OR SENSOR 

8.CHECK FOR SHORT IN CAN BUS LINES (COMBINATION METER ASSEMBLY)
  1. Reconnect the I94 CAN junction RH connector.

  1. Disconnect the I18 combination meter assembly connector.



    C210421E47
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I39-6 (CANH) - I39-14 (CANL)
    Cable disconnected from negative (-) auxiliary battery terminal
    108 to 132 Ω

    Text in Illustration 
    *1
    DLC3

    HINT:
    If the resistance becomes normal (between 108 to 132 Ω) when the connector is disconnected, there may be a short in the combination meter assembly.



NG
REPAIR OR REPLACE CAN MAIN BUS LINES (COMBINATION METER ASSEMBLY MAIN LINES)
OK

REPLACE COMBINATION METER ASSEMBLY (Click here)  

9.CHECK FOR SHORT IN CAN BUS LINES (ECM)
  1. Reconnect the I104 CAN junction LH connector.

  1. Disconnect the A25 ECM connector.



    C210421E47
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I39-6 (CANH) - I39-14 (CANL)
    Cable disconnected from negative (-) auxiliary battery terminal
    1 MΩ or higher

    Text in Illustration 
    *1
    DLC3

    HINT:
    1. Measure the resistance with the combination meter assembly main bus line connector (I18) disconnected.
    2. If the resistance changes to 1 MΩ or higher when the connector is disconnected, there may be a short in the ECM.



NG
REPAIR OR REPLACE CAN MAIN BUS LINES (ECM MAIN LINES)
OK

REPLACE ECM (Click here)