DTC B2285 Steering Lock Position Signal Circuit Malfunction |
| DTC Code | DTC Detection Condition | Trouble Area | DTC Output Confirmation Operation |
| B2285 | The steering lock position signal sent by the steering lock ECU (steering lock actuator assembly) via direct line and the steering lock position signal sent via LIN communication (1-trip detection logic*) do not match. |
| Disconnect the cable from the negative (-) auxiliary battery terminal, wait 30 seconds and then reconnect the cable to the negative (-) auxiliary battery terminal. Wait 40 seconds or more with the power switch off (with the steering wheel locked), then turn the power switch on (ACC) (with the steering unlocked) and wait 40 seconds or more. |
| Vehicle Condition when Malfunction Detected | Fail-safe Function when Malfunction Detected |
| The hybrid control system cannot be started. | The ECU does not send an hybrid control system start request. |

| DTC | Data List Item | Active Test Item |
| B2285 | Power Source Control
Entry&Start
| - |
| 1.CHECK FOR DTC (LIN COMMUNICATION SYSTEM) |
Check for DTCs (Click here).
|
| ||||
| OK | |
| 2.READ VALUE USING INTELLIGENT TESTER (STEERING UNLOCK SWITCH) |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body / Power Source Control / Data List.
According to the display on the intelligent tester, read the Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Steering Unlock Switch | State of steering unlock sensor signal output from steering lock actuator assembly/ON or OFF | ON: Steering unlocked OFF: Steering locked |
|
| Result | Proceed to |
| Data List item does not change | A |
| Data List item changes | B |
|
| ||||
| A | |
| 3.CHECK HARNESS AND CONNECTOR (POWER SOURCE) |
![]() |
Disconnect the I3 and I4 connectors from the power management control ECU.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I3-1 (AM22) - Body ground | Power switch off | 11 to 14 V |
| I4-7 (AM21) - Body ground | Power switch off | 11 to 14 V |
| *a | Front view of wire harness connector (to Power Management Control ECU) |
|
| ||||
| OK | |
| 4.CHECK HARNESS AND CONNECTOR (GROUND) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I3-5 (E01) - Body ground | Always | Below 1 Ω |
| I3-6 (E1) - Body ground | Always | Below 1 Ω |
| I4-4 (E12) - Body ground | Always | Below 1 Ω |
| I4-5 (E02) - Body ground | Always | Below 1 Ω |
| *a | Front view of wire harness connector (to Power Management Control ECU) |
|
| ||||
| OK | |
| 5.INSPECT STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| Positive (+) tester probe → I24-4 (SLP1) Negative (-) tester probe → Body ground | Steering locked* | 10 kΩ or higher |
| Steering unlocked* | Below 1 Ω |
| *a | Component with harness connected (Steering Lock ECU (Steering Lock Actuator Assembly)) |
|
| ||||
| OK | |
| 6.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY) |
Disconnect the I4 connector from the power management control ECU.
Disconnect the I24 connector from the steering lock ECU (steering lock actuator assembly).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I4-16 (SLP) - I24-4 (SLP1) | Always | Below 1 Ω |
| I4-16 (SLP) or I24-4 (SLP1) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||