Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM

DTC    C1203/95    ECM Communication Circuit Malfunction

for Preparation Click here


DESCRIPTION

The circuit is used to send TRC and VSC information from the skid control ECU to the power management control ECU, and hybrid control system information from the power management control ECU to the skid control ECU via the CAN communication system.
Identification information sent from other ECUs is stored when shipped from the factory and used as default values.

NOTICE:
DTC C1203/95 is output when an incorrect ECU is installed. If initialization is performed and learning occurs with an incorrect ECU installed, operations and functions will differ from that stored when the vehicle was shipped from the factory. Therefore, make sure that learning occurs properly.


DTC No.
INF Code
DTC Detection Condition
Trouble Area
C1203/95
-
Either of the following is detected:
  1. Identification information sent from other ECUs does not match with the value stored when shipped from the factory.
  2. No stored information for destination.
  1. The wrong ECU or sensor was installed
  2. Skid control ECU (Brake booster with master cylinder assembly)

INSPECTION PROCEDURE

NOTICE:
When replacing the skid control ECU (brake booster with master cylinder assembly), perform initialization and calibration of the linear solenoid valve (Click here).

1.CHECK PART NUMBER
  1. Check that the proper power management control ECU, main body ECU (multiplex network body ECU), yaw rate and acceleration sensor (for separate type) and/or yaw rate and acceleration sensor (airbag sensor assembly) (for built-in type) are installed.

    OK:
    Proper ECUs and sensor are installed.

  1. Check if the power management control ECU, main body ECU (multiplex network body ECU), yaw rate and acceleration sensor (for separate type) and/or yaw rate and acceleration sensor (airbag sensor assembly) (for built-in type) were replaced before the DTC was recorded.

    OK:
    ECU or sensor were not replaced.


    Result:

    Result
    Proceed to
    OK
    A
    NG (A proper power management control ECU is not installed and/or the power management control ECU was replaced.)
    B
    NG (A proper main body ECU (multiplex network body ECU) is not installed and/or the main body ECU (multiplex network body ECU) was replaced.)
    C
    NG (A proper yaw rate and acceleration sensor is not installed and/or the yaw rate and acceleration sensor was replaced (for separate type).)
    D
    NG (A proper yaw rate and acceleration sensor (airbag sensor assembly) is not installed and/or the yaw rate and acceleration sensor (airbag sensor assembly) was replaced (for built-in type).)
    E



B
REPLACE POWER MANAGEMENT CONTROL ECU (Click here)

C
REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)

D
REPLACE YAW RATE AND ACCELERATION SENSOR (Click here)

E
REPLACE AIRBAG SENSOR ASSEMBLY (Click here)
A


2.PERFORM INITIALIZATION AND CALIBRATION OF LINEAR SOLENOID VALVE
  1. Perform initialization and calibration of the linear solenoid valve (Click here).

    HINT:
    Before performing initialization and calibration of the linear solenoid valve, C1203/95 will be output.


NEXT


3.RECONFIRM DTC
  1. Turn the power switch off.

  1. Clear the DTCs (Click here).

  1. Turn the power switch on (IG).

  1. Check if the same DTC is output (Click here).

    Result:

    Result
    Proceed to
    DTC C1203/95 is output (for LHD).
    A
    DTC C1203/95 is output (for RHD).
    B
    DTC C1203/95 is not output.
    C



B
REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (Click here)

C
END
A

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (Click here)