DTC C1214/62 Hydraulic Control System Malfunction |
| DTC No. | INF Code | DTC Detection Condition | Trouble Area |
| C1214/62 | 431 | Decrease in hydraulic pressure control performance. (Pressure increase malfunction) |
|
| ↑ | 432 | Decrease in hydraulic pressure control performance. (Pressure decrease malfunction) | ↑ |
| ↑ | 433 | Malfunctions such as leaks occur in the SLA valve. | ↑ |
| ↑ | 434 435 | Malfunctions such as leaks occur in the SLR valve. | ↑ |
| ↑ | 436 437 | Decrease in hydraulic pressure control performance. | ↑ |
| ↑ | 438 | Malfunctions such as leaks occur in a hydraulic circuit valve. | Brake actuator (Brake booster with master cylinder assembly) |
| 1.CHECK FOR FLUID LEAK |
Check that there are no fluid leaks in the brake lines between the brake actuator (brake booster with master cylinder assembly) and the wheel cylinders.
Check that the brakes are not dragging.
|
| ||||
| OK | |
| 2.PERFORM AIR BLEEDING |
Clear the DTCs (Click here).
Perform the air bleeding procedure in Bleed Brake System .
| NEXT | |
| 3.CHECK BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (ACTUATOR SIDE) |
Make sure that there is no looseness at the locking part and the connecting part of the connector.
Disconnect the skid control ECU (brake booster with master cylinder assembly) connector 2 minutes after the power switch is turned off.
Check both the connector body and the terminals for deformation and corrosion.
| Result | Proceed to |
| OK | A |
| NG (for LHD) | B |
| NG (for RHD) | C |
|
| ||||
|
| ||||
| A | |
| 4.CHECK HARNESS AND CONNECTOR (VEHICLE SIDE) |
Measure the voltage and resistance on the wire harness side (Click here).
|
| ||||
| OK | |
| 5.READ VALUE USING INTELLIGENT TESTER (WHEEL CYLINDER PRESSURE SENSOR) |
Reconnect the skid control ECU (brake booster with master cylinder assembly) connector.
Connect an LSPV gauge set.
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Select the Data List on the intelligent tester (Click here).
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Wheel Cylinder Pressure Sensor | Wheel cylinder pressure sensor / Min.: 0.00 V, Max.: 5.00 V | When brake pedal released: 0.10 to 0.90 V | Reading increases when brake pedal is depressed |
Check the output value of the wheel cylinder pressure sensor at each hydraulic pressure level during electronically controlled brake system control.
| Hydraulic Pressure (MPa (kgf/cm2, psi)) | Wheel Cylinder Pressure Sensor (V) |
| 2.0 (20.4, 290) | 0.53 to 1.33 |
| 5.0 (51.0, 725) | 1.12 to 1.92 |
| 7.0 (71.4, 1015) | 1.52 to 2.32 |
| 10.0 (102.0, 1451) | 2.14 to 2.94 |
| Hydraulic Pressure (MPa (kgf/cm2, psi)) | Wheel Cylinder Pressure Sensor (V) |
| 2.0 (20.4, 290) | 0.53 to 1.33 |
| 5.0 (51.0, 725) | 1.12 to 1.92 |
| 7.0 (71.4, 1015) | 1.52 to 2.32 |
| 10.0 (102.0, 1451) | 2.14 to 2.94 |
| Result | Proceed to |
| OK | A |
| NG (for LHD) | B |
| NG (for RHD) | C |
|
| ||||
|
| ||||
| A | |
| 6.CHECK BRAKE DISC |
Turn the power switch off.
Disconnect the brake pedal stroke sensor assembly connector.
Perform a road test according to Freeze Frame Data or customer problem analysis. While driving, check for abnormal brake pedal vibration caused by brake discs that are worn or have excess runout.
|
| ||||
| OK | |
| 7.RECONFIRM DTC |
Reconnect the brake pedal stroke sensor assembly connector.
Clear the DTCs (Click here).
Perform a road test under the same malfunction conditions recreated based on the Freeze Frame Data or customer problem analysis.
Check if the same DTC is output (Click here).
| Result | Proceed to |
| DTC C1214/62 is not output. | A |
| DTC C1214/62 is output (for LHD). | B |
| DTC C1214/62 is output (for RHD). | C |
|
| ||||
|
| ||||
| A | ||
| ||