Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM

METER / GAUGE SYSTEM > Speedometer Malfunction

for Preparation Click here


DESCRIPTION

The meter ECU receives the vehicle speed signal from the skid control ECU via the CAN communication system. The speed sensors detect the wheel speed and send signals to the skid control ECU. The skid control ECU supplies power to the vehicle speed sensors. The skid control ECU creates the vehicle speed signal based on the pulses of the voltage.

HINT:
  1. Factors that affect the indicated vehicle speed include tire size, tire inflation, and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a intelligent tester. For details about testing and the margin of error, see the reference chart (Click here).
  2. If the vehicle speed sensor circuit has a malfunction, the skid control ECU stores the DTCs. Troubleshoot brake control system (Click here).


WIRING DIAGRAM


E143765E62


INSPECTION PROCEDURE

NOTICE:
If the vehicle speed is outside the allowable range when tested, perform the on-vehicle inspection .

HINT:
Before starting the following inspection, check tire size and tire air pressure.

1.CHECK CAN COMMUNICATION SYSTEM
  1. Check if CAN communication DTCs are output (Click here).

    Result:

    Result
    Proceed to
    DTCs are not output.
    A
    DTCs are output.
    B



B
GO TO CAN COMMUNICATION SYSTEM (Click here)
A


2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (SPEED METER OPERATION)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Combination Meter / Active Test.

  1. Check the operation by referring to the table below.

    Combination Meter 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Speed Meter Operation
    Speedometer
    0, 40, 80, 120, 160, 200, 240 km/h
    -

    OK:
    Speedometer indication is normal.



NG
REPLACE COMBINATION METER ASSEMBLY (Click here)
OK


3.CHECK BRAKE CONTROL SYSTEM
  1. Check if brake control system DTCs are output (Click here).


Result:

Result
Proceed to
DTCs are not output.
A
DTCs are output.
B



B
GO TO BRAKE CONTROL SYSTEM (Click here)
A


4.READ VALUE USING INTELLIGENT TESTER (VEHICLE SPEED, VEHICLE SPEED METER)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the intelligent tester on.

  1. Enter the following menus:

    1. for ABS/VSC/TRC: Chassis / ABS/VSC/TRC / Data List.

    2. for Combination Meter: Body / Combination Meter / Data List.

  1. Check the values by referring to the table below.

    ABS/VSC/TRC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Vehicle Speed
    Vehicle speed/Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
    Vehicle stopped: 0 km/h (0 mph)
    When driving at constant speed: No large fluctuations

    Combination Meter 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Vehicle Speed Meter
    Vehicle speed/Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph)
    Almost the same as actual vehicle speed
    -

    Result:

    Result
    Proceed to
    The data list values of the ECUs match.
    A
    The data list values of the ECUs do not match.
    B

    HINT:
    1. When the Data List values of the ECUs match, an internal malfunction of the combination meter assembly is suspected.
    2. When the Data List values of the ECUs do not match, a signal output error of the skid control ECU or an internal malfunction of the combination meter assembly is suspected.



B
Go to step 5
A

REPLACE COMBINATION METER ASSEMBLY (Click here)  

5.REPLACE COMBINATION METER ASSEMBLY
  1. Replace the combination meter assembly with a new or a known good one (Click here).


Result:

Result
Proceed to
The operation of the speedometer returns to normal.
A
The operation of the speedometer does not returns to normal (for LHD).
B
The operation of the speedometer does not returns to normal (for RHD).
C



B
REPLACE BRAKE BOOSTER ASSEMBLY (Click here)

C
REPLACE BRAKE BOOSTER ASSEMBLY (Click here)
A

END