Home › Vehicle Exterior › MIRROR (EXT) › OUTER REAR VIEW MIRROR

OUTER REAR VIEW MIRROR > INSPECTION

for Preparation Click here



1. INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH


  1. Check the operation of the mirror surface.



      B281818E01
    1. Disconnect the outer rear view mirror assembly RH connector.

    2. Apply auxiliary battery voltage and check the operation of the mirror.

      OK:
      Measurement Condition
      Specified Condition
      Auxiliary battery positive (+) → Terminal 6 (MV)
      Auxiliary battery negative (-) → Terminal 5 (M+)
      Turns upward
      Auxiliary battery positive (+) → Terminal 5 (M+)
      Auxiliary battery negative (-) → Terminal 6 (MV)
      Turns downward
      Auxiliary battery positive (+) → Terminal 4 (MH)
      Auxiliary battery negative (-) → Terminal 5 (M+)
      Turns left
      Auxiliary battery positive (+) → Terminal 5 (M+)
      Auxiliary battery negative (-) → Terminal 4 (MH)
      Turns right

      Text in Illustration 
      *a
      Component without harness connected
      (Outer Rear View Mirror Assembly RH)
      If the result is not as specified, replace the outer rear view mirror assembly RH.



  1. Check the operation of the retractable mirror.

    NOTICE:
    1. Disconnect and reconnect the auxiliary battery between each mirror position check.
    2. The mirror position cannot be changed manually when the auxiliary battery is connected. To change the mirror position manually, the auxiliary battery must be disconnected first.




      B199932E13
    1. Disconnect the outer rear view mirror assembly RH connector.

    2. For each position: Disconnect the auxiliary battery, set the mirror position by hand, connect the auxiliary battery, and check the retractable mirror's movement.

      OK:
      Tester Connection
      Condition
      Specified Condition
      Auxiliary battery positive (+) → Terminal 3 (MR)
      Auxiliary battery negative (-) → Terminal 9 (MF)
      Forward position (A)
      Moves from (A) to retracted position (E)
      Auxiliary battery positive (+) → Terminal 9 (MF)
      Auxiliary battery negative (-) → Terminal 3 (MR)
      Forward position (A)
      Does not move
      Auxiliary battery positive (+) → Terminal 3 (MR)
      Auxiliary battery negative (-) → Terminal 9 (MF)
      Position between forward position (A) and driving position (C)
      Moves from (B) to forward position (E)
      Auxiliary battery positive (+) → Terminal 9 (MF)
      Auxiliary battery negative (-) → Terminal 3 (MR)
      Position between forward position (A) and driving position (C)
      Moves from (B) to retracted position (A)
      Auxiliary battery positive (+) → Terminal 3 (MR)
      Auxiliary battery negative (-) → Terminal 9 (MF)
      Driving position (C)
      Moves from (C) to retracted position (E)
      Auxiliary battery positive (+) → Terminal 9 (MF)
      Auxiliary battery negative (-) → Terminal 3 (MR)
      Driving position (C)
      Does not move
      Auxiliary battery positive (+) → Terminal 3 (MR)
      Auxiliary battery negative (-) → Terminal 9 (MF)
      Position between driving position (C) and retracted position (E)
      Moves from (D) to retracted position (E)
      Auxiliary battery positive (+) → Terminal 9 (MF)
      Auxiliary battery negative (-) → Terminal 3 (MR)
      Position between driving position (C) and retracted position (E)
      Moves from (D) to driving position (C)
      Auxiliary battery positive (+) → Terminal 3 (MR)
      Auxiliary battery negative (-) → Terminal 9 (MF)
      Retracted position (E)
      Does not move
      Auxiliary battery positive (+) → Terminal 9 (MF)
      Auxiliary battery negative (-) → Terminal 3 (MR)
      Retracted position (E)
      Moves from (E) to driving position (C)

      Text in Illustration 
      *1
      (A) Forward Position
      *2
      (B)
      *3
      (C) Driving position
      *4
      (D)
      *5
      (E) Retracted Position
      *a
      Component without harness connected
      (Outer Rear View Mirror Assembly RH)
      If the result is not as specified, replace the outer rear view mirror assembly RH.



  1. Check the operation of the mirror heater.



      B281820E01
    1. Disconnect the outer rear view mirror assembly RH connector.

      HINT:
      The resistance of the mirror heater varies depending on the shape of the heater wire. Remove the mirror surface to check the shape of the heater wire before inspection.
      1. Remove the outer rear view mirror assembly RH (Click here).
      2. Check the shape of the heater wire (Click here).

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Heater Wire Shape A 
      Tester Connection
      Condition
      Specified Condition
      2 (HR+) - 8 (HR-)
      25°C (77°F)
      7.6 to 11.4 Ω
      Heater Wire Shape B 
      Tester Connection
      Condition
      Specified Condition
      2 (HR+) - 8 (HR-)
      25°C (77°F)
      9.2 to 13.8 Ω

      Text in Illustration 
      *a
      Component without harness connected
      (Outer Rear View Mirror Assembly RH)
      If the result is not as specified, replace the outer rear view mirror assembly RH.

    3. Connect the cable from the positive (+) terminal to terminal 2 and the negative auxiliary battery (-) terminal to terminal 8, then check that the mirror becomes warm.

      HINT:
      It takes a short time for the mirror to become warm.

      OK:
      Mirror becomes warm.

      If the result is not as specified, replace the outer rear view mirror assembly RH.



2. INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH


  1. Check the operation of the mirror surface.



      B281822E01
    1. Disconnect the outer rear view mirror assembly LH connector.

    2. Apply auxiliary battery voltage and check the operation of the mirror.

      OK:
      Measurement Condition
      Specified Condition
      Auxiliary battery positive (+) → Terminal 6 (MV)
      Auxiliary battery negative (-) → Terminal 5 (M+)
      Turns upward
      Auxiliary battery positive (+) → Terminal 5 (M+)
      Auxiliary battery negative (-) → Terminal 6 (MV)
      Turns downward
      Auxiliary battery positive (+) → Terminal 4 (MH)
      Auxiliary battery negative (-) → Terminal 5 (M+)
      Turns left
      Auxiliary battery positive (+) → Terminal 5 (M+)
      Auxiliary battery negative (-) → Terminal 4 (MH)
      Turns right

      Text in Illustration 
      *a
      Component without harness connected
      (Outer Rear View Mirror Assembly LH)
      If the result is not as specified, replace the outer rear view mirror assembly LH.



  1. Check the operation of the retractable mirror.

    NOTICE:
    1. Disconnect and reconnect the auxiliary battery between each mirror position check.
    2. The mirror position cannot be changed manually when the auxiliary battery is connected. To change the mirror position manually, the auxiliary battery must be disconnected first.




      B199933E12
    1. Disconnect the outer rear view mirror assembly LH connector.

    2. For each position: Disconnect the auxiliary battery, set the mirror position by hand, connect the auxiliary battery, and check the retractable mirror's movement.

      OK:
      Tester Connection
      Condition
      Specified Condition
      Auxiliary battery positive (+) → Terminal 3 (MR)
      Auxiliary battery negative (-) → Terminal 9 (MF)
      Forward position (A)
      Moves from (A) to retracted position (E)
      Auxiliary battery positive (+) → Terminal 9 (MF)
      Auxiliary battery negative (-) → Terminal 3 (MR)
      Forward position (A)
      Does not move
      Auxiliary battery positive (+) → Terminal 3 (MR)
      Auxiliary battery negative (-) → Terminal 9 (MF)
      Position between forward position (A) and driving position (C)
      Moves from (B) to retracted position (E)
      Auxiliary battery positive (+) → Terminal 9 (MF)
      Auxiliary battery negative (-) → Terminal 3 (MR)
      Position between forward position (A) and driving position (C)
      Moves from (B) to forward position (A)
      Auxiliary battery positive (+) → Terminal 3 (MR)
      Auxiliary battery negative (-) → Terminal 9 (MF)
      Driving position (C)
      Moves from (C) to retracted position (E)
      Auxiliary battery positive (+) → Terminal 9 (MF)
      Auxiliary battery negative (-) → Terminal 3 (MR)
      Driving position (C)
      Does not move
      Auxiliary battery positive (+) → Terminal 3 (MR)
      Auxiliary battery negative (-) → Terminal 9 (MF)
      Position between driving position (C) and retracted position (E)
      Moves from (D) to retracted position (E)
      Auxiliary battery positive (+) → Terminal 9 (MF)
      Auxiliary battery negative (-) → Terminal 3 (MR)
      Position between driving position (C) and retracted position (E)
      Moves from (D) to driving position (C)
      Auxiliary battery positive (+) → Terminal 3 (MR)
      Auxiliary battery negative (-) → Terminal 9 (MF)
      Retracted position (E)
      Does not move
      Auxiliary battery positive (+) → Terminal 9 (MF)
      Auxiliary battery negative (-) → Terminal 3 (MR)
      Retracted position (E)
      Moves from (E) to driving position (C)

      Text in Illustration 
      *1
      (A) Forward Position
      *2
      (B)
      *3
      (C) Driving position
      *4
      (D)
      *5
      (E) Retracted Position
      *a
      Component without harness connected
      (Outer Rear View Mirror Assembly LH)
      If the result is not as specified, replace the outer rear view mirror assembly LH.



  1. Check the operation of the mirror heater.



      B281824E01
    1. Disconnect the outer rear view mirror assembly LH connector.

      HINT:
      The resistance of the mirror heater varies depending on the shape of the heater wire. Remove the mirror surface to check the shape of the heater wire before inspection.
      1. Remove the outer rear view mirror assembly LH (Click here).
      2. Check the shape of the heater wire (Click here).

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Heater Wire Shape A 
      Tester Connection
      Condition
      Specified Condition
      2 (HL+) - 8 (HL-)
      25°C (77°F)
      7.6 to 11.4 Ω
      Heater Wire Shape B 
      Tester Connection
      Condition
      Specified Condition
      2 (HL+) - 8 (HL-)
      25°C (77°F)
      9.2 to 13.8 Ω

      Text in Illustration 
      *a
      Component without harness connected
      (Outer Rear View Mirror Assembly LH)
      If the result is not as specified, replace the outer rear view mirror assembly LH.

    3. Connect the cable from the positive (+) terminal to terminal 2 and the negative auxiliary battery (-) terminal to terminal 8, then check that the mirror becomes warm.

      HINT:
      It takes a short time for the mirror to become warm.

      OK:
      Mirror becomes warm.

      If the result is not as specified, replace the outer rear view mirror assembly LH.