Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM

ELECTRONICALLY CONTROLLED BRAKE SYSTEM > TRC OFF Indicator Light Remains ON

for Preparation Click here


DESCRIPTION

The skid control ECU (brake booster with master cylinder assembly) is connected to the combination meter assembly via CAN communication.
Pressing the VSC OFF switch (vehicle stability control switch) turns off traction control and pressing and holding this switch turns off traction and VSC controls. If TRC control is turned off, the TRC OFF message will be displayed on the multi-information display.

WIRING DIAGRAM


C239016E20


INSPECTION PROCEDURE

NOTICE:
When replacing the skid control ECU (brake booster with master cylinder assembly), perform initialization and calibration of the linear solenoid valve (Click here).

1.CHECK CAN COMMUNICATION SYSTEM
  1. Check if CAN communication system DTCs are output (Click here).

    Result:

    Result
    Proceed to
    DTC is not output.
    A
    DTC is output.
    B



B
INSPECT CAN COMMUNICATION SYSTEM (Click here)
A


2.CHECK IF SKID CONTROL ECU CONNECTOR IS SECURELY CONNECTED
  1. Check if the skid control ECU (brake booster with master cylinder assembly) connector is securely connected.

    OK:
    The connector is securely connected.



NG
CONNECT CONNECTOR TO ECU CORRECTLY
OK


3.CHECK AUXILIARY BATTERY
  1. Check the auxiliary battery voltage.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    Auxiliary battery
    Power switch on (IG)
    11 to 14 V
    Auxiliary battery
    Power switch on (READY)
    11 to 15.5 V



NG
CHARGE OR REPLACE AUXILIARY BATTERY
OK


4.READ VALUE USING INTELLIGENT TESTER (VEHICLE STABILITY CONTROL SWITCH)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Select the Data List on the intelligent tester (Click here).

    ABS/VSC/TRC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    TRC/VSC Off Mode
    TRC/VSC off mode / Normal, TRC OFF, Unknown or VSC OFF
    Normal: Normal mode
    TRC OFF: TRC off mode
    Unknown: Unspecified
    VSC OFF: VSC off mode
    -

  1. Using the intelligent tester, check that the switch condition on the intelligent tester changes according to VSC OFF switch (vehicle stability control switch) operation.



NG
Go to step 6
OK


5.INSPECT COMBINATION METER ASSEMBLY
  1. Turn the power switch off.

  1. Perform the Active Test of the combination meter assembly (meter CPU) using the intelligent tester (Click here).

  1. Check the combination meter assembly.

    OK:
    The multi-information display turns on or off in accordance with intelligent tester operation.


    Result:

    Result
    Proceed to
    OK (for LHD)
    A
    OK (for RHD)
    B
    NG
    C

    HINT:
    If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing the part (Click here).



B
REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (Click here)

C
REPLACE COMBINATION METER ASSEMBLY (Click here)
A

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (Click here)  

6.INSPECT VEHICLE STABILITY CONTROL SWITCH


    C311100E03
  1. Turn the power switch off.

  1. Disconnect the VSC OFF switch (vehicle stability control switch) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    9 (+) - 6 (E)
    Switch is pushed
    Below 1 Ω
    9 (+) - 6 (E)
    Switch is not pushed
    10 kΩ or higher

    Text in Illustration 
    *a
    Component without harness connected
    (VSC OFF Switch (Vehicle Stability Control Switch))



NG
REPLACE VEHICLE STABILITY CONTROL SWITCH (Click here)
OK


7.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - VEHICLE STABILITY CONTROL SWITCH)
  1. Disconnect the skid control ECU (brake booster with master cylinder assembly) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A28-8 (CSW) - I179-9 (+)
    Always
    Below 1 Ω
    A28-8 (CSW) - Body ground
    Always
    10 kΩ or higher
    I179-6 (E) - Body ground
    Always
    Below 1 Ω


    Result:

    Result
    Proceed to
    OK (for LHD)
    A
    OK (for RHD)
    B
    NG
    C

    HINT:
    If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step (Click here).



B
REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (Click here)

C
REPAIR OR REPLACE HARNESS OR CONNECTOR
A

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (Click here)