RADIATOR > INSTALLATION |
| 1. INSTALL RADIATOR ASSEMBLY |
![]() |
Install the fan assembly to the radiator with the 2 guides at the bottom and 3 claws on the top.
| *a | Guide |
Install the 2 lower radiator supports to the radiator assembly.
![]() |
Install the radiator with fan assembly.
Install the radiator with fan assembly to the condenser assembly and radiator assembly (for inverter coolant) with the 4 bolts.
Connect the No. 4 inverter cooling hose with the clamp.
Connect the connector and the 2 clamps.
Connect the 2 clamps.
| 2. INSTALL UPPER RADIATOR SUPPORT |
Install the 2 radiator support cushions to the radiator assembly.
Install the upper radiator support with the 5 bolts and connect the hood lock control cable clamp to the upper radiator support.
Connect the 2 connectors.
| 3. INSTALL HOOD LOCK ASSEMBLY (for LHD) |
![]() |
Apply MP grease to the sliding areas of the lock.
Connect the hood lock control cable assembly.
Install the hood lock assembly with the 2 bolts and hood lock bolt.
Connect the connector.
| 4. INSTALL HOOD LOCK ASSEMBLY (for RHD) |
![]() |
Apply MP grease to the sliding areas of the lock.
Connect the hood lock control cable assembly.
Install the hood lock assembly with the 2 bolts and hood lock bolt.
Connect the connector.
| 5. CONNECT NO. 1 INVERTER COOLING PIPE ASSEMBLY |
![]() |
Temporarily install the bolt A.
Install the bolt B.
Fully tighten the bolt A.
| 6. CONNECT NO. 2 RADIATOR HOSE |
Connect the No. 2 radiator hose and clamp.
| 7. CONNECT NO. 1 RADIATOR HOSE |
Connect the No. 1 radiator hose.
| 8. INSTALL RADIATOR RESERVE TANK ASSEMBLY |
Install the radiator reserve tank with the 2 bolts.
Connect the radiator reserve tank hose.
| 9. INSTALL NO. 5 INVERTER BRACKET |
Temporarily install the No. 5 inverter bracket with the 2 bolts.
![]() |
Tighten the 2 bolts in the order shown in the illustration.
| 10. INSTALL INLET AIR CLEANER ASSEMBLY |
Install the inlet air cleaner with the 2 bolts.
| 11. INSTALL FRONT BUMPER ASSEMBLY |
| 12. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL |
| 13. INSTALL LUGGAGE TRIM SERVICE HOLE COVER |
Engage the claw to connect the luggage trim service hole cover.
| 14. ADD COOLANT (for Engine) |
Tighten the radiator drain cock plug by hand.
Slowly fill the radiator with TOYOTA Super Long Life Coolant (SLLC).
| Item | Capacity |
| Engine coolant | 7.2 liters (7.6 US qts, 6.3 lmp. qts) |
Slowly pour coolant into the radiator reserve tank assembly until it reaches the full line.
Squeeze the No. 1 and No. 2 radiator hoses several times by hand, and then check the level of the coolant.
If the coolant level is low, add coolant.
Install the radiator cap sub-assembly and reserve tank cap.
Put the engine in inspection mode (Click here).
Bleed air from the cooling system.
Warm up the engine until the thermostat opens. While the thermostat is open, circulate the coolant for several minutes.
Squeeze the No. 1 and No. 2 radiator hoses several times by hand to bleed air.
Stop the engine and wait until the engine coolant cools down.
Add engine coolant to the full line on the radiator reserve tank assembly.
| 15. INSPECT FOR COOLANT LEAK (for Engine) |
![]() |
Fill the radiator with coolant and attach a radiator cap tester.
Put the engine in inspection mode (Click here).
Warm up the engine.
Using a radiator cap tester, increase the pressure inside the radiator to 118 kPa (1.2 kgf/cm2, 17 psi), and check that the pressure does not drop.
If the pressure drops, check the hoses, radiator and water pump for leaks. If no external leaks are found, check the heater core, cylinder block and cylinder head.
| 16. INSTALL ENGINE UNDER COVER LH |
| 17. INSTALL ENGINE UNDER COVER RH |
| 18. INSTALL FRONT WHEEL OPENING EXTENSION PAD LH |
| 19. INSTALL FRONT WHEEL OPENING EXTENSION PAD RH |