Home › Engine / Hybrid System › 2AR-FXE FUEL › FUEL TANK

FUEL TANK > INSTALLATION

for Preparation Click here



1. INSTALL NO. 4 FUEL TUBE CLAMP
  1. Install the 3 No. 4 fuel tube clamps.



2. INSTALL FUEL MAIN TUBE SUPPORT
  1. Install the fuel main tube support with the bolt.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



3. INSTALL FUEL PUMP TUBE SUB-ASSEMBLY
  1. Install the fuel pump tube sub-assembly to the fuel main tube support and No. 4 fuel tube clamp.



4. INSTALL FUEL CUT OFF WITH TUBE VALVE ASSEMBLY
  1. Install 2 new fuel tank breather tube gaskets to the fuel tank assembly.



    A060494E03
  1. Apply a light coat of gasoline around 2 new fuel cut off with tube valve assemblies as shown in the illustration, and carefully insert them into the fuel tank assembly.
    Text in Illustration 
    *a
    Apply gasoline around the valve

    NOTICE:
    Be careful not to drop the fuel tank breather tube gaskets into the fuel tank assembly.

  1. Check that the fuel cut off with tube valve assemblies are fully inserted.

  1. Connect the fuel emission hose to the fuel cut off with tube valve assembly, then install it with the clamp.



5. INSTALL NO. 3 FUEL TANK PROTECTOR


    A255936E02
  1. Install the No. 3 fuel tank protector by sliding it to engage the claws as shown in the illustration.



6. INSTALL NO. 2 FUEL TANK PROTECTOR


    A255937E02
  1. Install the No. 2 fuel tank protector by sliding it to engage the claws as shown in the illustration.



7. INSTALL NO. 1 FUEL TANK CUSHION


    A259310
  1. Install 7 new No. 1 fuel tank cushions as shown in the illustration.



8. INSTALL FUEL TANK ASSEMBLY
  1. Install the 4 clip nuts.



    A129491
  1. Install the 2 fuel tank bands with the 2 pins as shown in the illustration.

  1. Support the fuel tank assembly using an engine lifter.



    A255940E01
  1. Raise the engine lifter so that the breather tube fuel hose can be connected as shown in the illustration.
    Text in Illustration 
    *1
    Claw
    *a
    Upper
    *b
    135°
    *c
    0 to 3 mm (0 to 0.12 in.)

    NOTICE:
    Slowly raise the engine lifter so as not to drop the fuel tank assembly.



    A255939E01
  1. Connect the fuel tank to filler pipe hose to the fuel tank assembly as shown in the illustration, then install the hose with the clamp.
    Text in Illustration 
    *1
    Claw
    *a
    Upper
    *b
    90°
    *c
    Clamp Area
    17.5mm (0.689 in.)
    *d
    0 to 3 mm (0 to 0.12 in.)

  1. Slightly lift the engine lifter, then install the fuel tank assembly to the vehicle.

  1. Tighten the 2 bolts of the fuel tank bands.

    Torque:
    45 N*m{ 459 kgf*cm , 33 ft.*lbf }



    A255941E01
  1. Connect the fuel emission hose to the charcoal canister, then install it with the clamp as shown in the illustration.
    Text in Illustration 
    *a
    Upper
    *b
    30°
    *c
    120°



9. CONNECT FUEL PUMP TUBE SUB-ASSEMBLY


    A255958E01
  1. Align the fuel tube connector with the fuel pipe, and push the fuel tube connector in until the retainer makes a "click" sound.
    Text in Illustration 
    *1
    Retainer
    *2
    Fuel Pipe
    *3
    Fuel Tube Connector
    *4
    O-ring

    NOTICE:
    1. Check that there are no scratches or foreign matter around the connecting parts of the fuel tube connector and fuel pipe before connecting them.
    2. After connecting the fuel tube connector, check that it is securely connected by pulling it.



10. INSTALL LOWER CENTER FUEL TANK PROTECTOR
  1. Install the lower center fuel tank protector with the 4 bolts.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



11. INSTALL REAR NO. 1 STABILIZER BAR BRACKET
  1. Install the 2 rear No. 1 stabilizer bar brackets with the 4 bolts.

    Torque:
    31 N*m{ 316 kgf*cm , 23 ft.*lbf }



12. INSTALL NO. 3 PARKING BRAKE CABLE ASSEMBLY
  1. Install the No. 3 parking brake cable assembly with the bolt and nut.

    Torque:
    6.0 N*m{ 61 kgf*cm , 53 in.*lbf }



13. INSTALL NO. 2 PARKING BRAKE CABLE ASSEMBLY
  1. Install the No. 2 parking brake cable assembly with the bolt and nut.

    Torque:
    6.0 N*m{ 61 kgf*cm , 53 in.*lbf }



14. INSTALL NO. 1 FLOOR UNDER COVER
  1. Install the No. 1 floor under cover with the 5 nuts and 2 clips.

    Torque:
    Nut:
    4.0 N*m{ 41 kgf*cm , 35 in.*lbf }

    HINT:
    The 5 nuts and 2 clips are attached to the No. 1 floor under cover.



15. INSTALL NO. 2 FLOOR UNDER COVER
  1. Install the No. 2 floor under cover with the 6 nuts.

    Torque:
    4.0 N*m{ 41 kgf*cm , 35 in.*lbf }

    HINT:
    The 6 nuts are attached to the No. 2 floor under cover.

  1. Install the 2 clips.



16. INSTALL CENTER EXHAUST PIPE ASSEMBLY
(Click here)


17. INSTALL FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY
(Click here)


18. ADD FUEL


19. INSPECT FOR EXHAUST GAS LEAK