FUEL TANK > INSTALLATION |
| 1. INSTALL NO. 4 FUEL TUBE CLAMP |
Install the 3 No. 4 fuel tube clamps.
| 2. INSTALL FUEL MAIN TUBE SUPPORT |
Install the fuel main tube support with the bolt.
| 3. INSTALL FUEL PUMP TUBE SUB-ASSEMBLY |
Install the fuel pump tube sub-assembly to the fuel main tube support and No. 4 fuel tube clamp.
| 4. INSTALL FUEL CUT OFF WITH TUBE VALVE ASSEMBLY |
Install 2 new fuel tank breather tube gaskets to the fuel tank assembly.
![]() |
Apply a light coat of gasoline around 2 new fuel cut off with tube valve assemblies as shown in the illustration, and carefully insert them into the fuel tank assembly.
| *a | Apply gasoline around the valve |
Check that the fuel cut off with tube valve assemblies are fully inserted.
Connect the fuel emission hose to the fuel cut off with tube valve assembly, then install it with the clamp.
| 5. INSTALL NO. 3 FUEL TANK PROTECTOR |
![]() |
Install the No. 3 fuel tank protector by sliding it to engage the claws as shown in the illustration.
| 6. INSTALL NO. 2 FUEL TANK PROTECTOR |
![]() |
Install the No. 2 fuel tank protector by sliding it to engage the claws as shown in the illustration.
| 7. INSTALL NO. 1 FUEL TANK CUSHION |
![]() |
Install 7 new No. 1 fuel tank cushions as shown in the illustration.
| 8. INSTALL FUEL TANK ASSEMBLY |
Install the 4 clip nuts.
![]() |
Install the 2 fuel tank bands with the 2 pins as shown in the illustration.
Support the fuel tank assembly using an engine lifter.
![]() |
Raise the engine lifter so that the breather tube fuel hose can be connected as shown in the illustration.
| *1 | Claw |
| *a | Upper |
| *b | 135° |
| *c | 0 to 3 mm (0 to 0.12 in.) |
![]() |
Connect the fuel tank to filler pipe hose to the fuel tank assembly as shown in the illustration, then install the hose with the clamp.
| *1 | Claw |
| *a | Upper |
| *b | 90° |
| *c | Clamp Area 17.5 mm (0.689 in.) |
| *d | 0 to 3 mm (0 to 0.12 in.) |
Slightly lift the engine lifter, then install the fuel tank assembly to the vehicle.
Tighten the 2 bolts of the fuel tank bands.
![]() |
Connect the fuel emission hose to the charcoal canister, then install it with the clamp as shown in the illustration.
| *a | Upper |
| *b | 30° |
| *c | 120° |
| 9. CONNECT FUEL PUMP TUBE SUB-ASSEMBLY |
![]() |
Align the fuel tube connector with the fuel pipe, and push the fuel tube connector in until the retainer makes a "click" sound.
| *1 | Retainer |
| *2 | Fuel Pipe |
| *3 | Fuel Tube Connector |
| *4 | O-ring |
| 10. INSTALL LOWER CENTER FUEL TANK PROTECTOR |
Install the lower center fuel tank protector with the 4 bolts.
| 11. INSTALL REAR NO. 1 STABILIZER BAR BRACKET |
Install the 2 rear No. 1 stabilizer bar brackets with the 4 bolts.
| 12. INSTALL NO. 3 PARKING BRAKE CABLE ASSEMBLY |
Install the No. 3 parking brake cable assembly with the bolt and nut.
| 13. INSTALL NO. 2 PARKING BRAKE CABLE ASSEMBLY |
Install the No. 2 parking brake cable assembly with the bolt and nut.
| 14. INSTALL NO. 1 FLOOR UNDER COVER |
Install the No. 1 floor under cover with the 5 nuts and 2 clips.
Install the screw.
| 15. INSTALL NO. 2 FLOOR UNDER COVER |
Install the No. 2 floor under cover with the 6 nuts.
Install the screw and 2 clips.
| 16. INSTALL CENTER EXHAUST PIPE ASSEMBLY |
| 17. INSTALL FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY |
| 18. ADD FUEL |
| 19. INSPECT FOR EXHAUST GAS LEAK |