Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM

DTC    C1511/11    Torque Sensor 1 Malfunction

DTC    C1512/11    Torque Sensor 2 Malfunction

DTC    C1513/11    Torque Sensor Deviation Excessive

DTC    C1514/11    Torque Sensor Power Supply Voltage Malfunction

for Preparation Click here


DESCRIPTION

The torque sensor converts the steering wheel rotation torque into electric signals and sends them to the power steering ECU assembly.

DTC No.
DTC Detection Condition
Trouble Area
C1511/11
Torque sensor malfunction
  1. Electric power steering column sub-assembly (Torque sensor)
  2. Power steering ECU assembly
C1512/11
C1513/11
C1514/11

WIRING DIAGRAM


C240198E02


INSPECTION PROCEDURE

NOTICE:
If the power steering ECU assembly has been replaced, perform assist map writing (Click here).

1.CHECK CONNECTOR CONNECTION CONDITION (TORQUE SENSOR - ECU)
  1. Check the connection condition of the torque sensor connector.

    OK:
    Torque sensor connector is securely connected to the power steering ECU assembly.



NG
CONNECT CONNECTOR
OK


2.CHECK POWER STEERING ECU ASSEMBLY (TRQV, TRQF VOLTAGE)
C238944E03
  1. Turn the power switch on (READY).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    a-3 (TRQV) - a-1 (TRQG)
    Power switch on (IG)
    8.5 to 10.5 V
    a-5 (TRQF) - a-1 (TRQG)
    Power switch on (IG)
    3.35 to 3.37 V

    Text in Illustration 
    *a
    Component with harness connected
    (Power Steering ECU Assembly)



NG
REPLACE POWER STEERING ECU ASSEMBLY (Click here)
OK


3.CHECK POWER STEERING ECU ASSEMBLY (TRQ1, TRQ2 VOLTAGE)


    C238944E04
  1. Turn the power switch on (READY).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition (Steering Wheel Position)
    Specified Condition
    a-7 (TRQ1) - a-1 (TRQG)
    Power switch on (READY)
    Steering wheel not being turned (without load)
    2.3 to 2.7 V
    Power switch on (READY)
    Steering wheel being turned to the right with vehicle stopped
    2.5 to 4.7 V
    Power switch on (READY)
    Steering wheel being turned to the left with vehicle stopped
    0.3 to 2.5 V
    a-2 (TRQ2) - a-1 (TRQG)
    Power switch on (READY)
    Steering wheel not being turned (without load)
    2.3 to 2.7 V
    Power switch on (READY)
    Steering wheel being turned to the right with vehicle stopped
    0.3 to 2.5 V
    Power switch on (READY)
    Steering wheel being turned to the left with vehicle stopped
    2.5 to 4.7 V

  1. Under each condition, measure the voltage at terminals TRQ1 and TRQ2, and calculate the sum.

    Standard Voltage:
    Inspection Item
    Condition (Steering Wheel Position)
    Specified Condition
    Sum of voltage between a-7 (TRQ1) and a-1 (TRQG) and voltage between a-2 (TRQ2) and a-1 (TRQG)
    Power switch on (READY)
    Steering wheel not being turned (without load)
    Between 4.85 V and 5.35 V
    Power switch on (READY)
    Steering wheel being turned to the right with vehicle stopped
    Power switch on (READY)
    Steering wheel being turned to the left with vehicle stopped

    Text in Illustration 
    *a
    Component with harness connected
    (Power Steering ECU Assembly)



NG
REPLACE ELECTRIC POWER STEERING COLUMN SUB-ASSEMBLY (Click here)
OK

REPLACE POWER STEERING ECU ASSEMBLY (Click here)