Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM

DTC    C1551/25    IG Power Supply Voltage Malfunction

for Preparation Click here


DESCRIPTION

The power steering ECU assembly distinguishes the power switch status as on (IG) or off through the IG power source circuit.

DTC No.
DTC Detection Condition
Trouble Area
C1551/25
IG power source circuit malfunction inside ECU
  1. EPS-IG1 fuse
  2. IG power source circuit
  3. ECU wire sub-assembly
  4. Power steering ECU assembly

WIRING DIAGRAM


C250100E02


INSPECTION PROCEDURE

NOTICE:
If the power steering ECU assembly has been replaced, perform assist map writing (Click here).

HINT:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.CHECK CONNECTOR CONNECTION CONDITION AND GROUND WIRE
  1. Check the connection condition of the ECU wire sub-assembly and power steering ECU assembly connectors.

    OK:
    The ECU wire sub-assembly and power steering ECU assembly connectors are securely connected.

  1. Check that the ground wire is securely installed with the bolt (Click here).

    OK:
    The ground wire is securely installed with the bolt.



NG
CONNECT CONNECTOR OR INSTALL GROUND WIRE (Click here)
OK


2.READ VALUE USING INTELLIGENT TESTER (IG POWER SUPPLY)
  1. Turn the power switch off.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the intelligent tester on.

  1. Enter the following menus: Chassis / EMPS / Data List.

  1. Select the item "IG power supply" in the Data List and read the value displayed on the intelligent tester.

    EMPS 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    IG power supply
    IG power supply/
    Min.: 0.0000 V
    Max.: 20.1531 V
    9 to 16 V
    Power switch on (IG)

    OK:
    The normal condition value is displayed on the intelligent tester.



NG
Go to step 3
OK

CHECK INTERMITTENT PROBLEMS (Click here)  

3.CHECK HARNESS AND CONNECTOR (AUXILIARY BATTERY - ECU WIRE SUB-ASSEMBLY)


    C240359E02
  1. Disconnect the Ij2 connector from the ECU wire sub-assembly.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    Ij2-5 (IG) - Body ground
    Power switch on (IG)
    9 to 16 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to ECU Wire Sub-assembly)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK ECU WIRE SUB-ASSEMBLY


    C240351E02
  1. Connect the Ij2 connector to the ECU wire sub-assembly.

  1. Disconnect the power steering ECU assembly j3 and j2 connectors.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    j3-1 (IG) - Body ground
    Power switch on (IG)
    9 to 16 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    j2-2 (PGND) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Power Steering ECU Assembly)



NG
REPAIR OR REPLACE ECU WIRE SUB-ASSEMBLY
OK

REPLACE POWER STEERING ECU ASSEMBLY (Click here)