Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM

DTC    C1524/24    Motor Circuit Malfunction

DTC    C1555/25    Motor Relay Welding Failure

for Preparation Click here


DESCRIPTION

The power steering ECU assembly supplies current to the power steering motor assembly through the motor circuit.

DTC No.
DTC Detection Condition
Trouble Area
C1524/24
Short (or open) in motor circuit or abnormal voltage or current in motor circuit
  1. Power steering motor assembly
  2. Power steering ECU assembly
C1555/25
Motor relay circuit malfunction

WIRING DIAGRAM


C246148E04


INSPECTION PROCEDURE

NOTICE:
If the power steering ECU assembly has been replaced, perform assist map writing (Click here).

1.INSPECT TIGHTENING TORQUE OF MOTOR TERMINAL BOLT
  1. Disengage the 4 claws to remove the protector (Click here).

  1. Check that the motor terminal bolts are tightened to the specified torque (Click here).

    OK:
    The motor terminal bolts are tightened to the specified torque.



NG
TIGHTEN BOLT TO SPECIFIED TORQUE
OK


2.INSPECT POWER STEERING MOTOR ASSEMBLY


    C240264E01
  1. Remove the power steering motor assembly (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    c-1 (PHA) - c-2 (PHB)
    25°C (77°F)
    12.7 to 17.2 mΩ
    c-2 (PHB) - c-3 (PHC)
    25°C (77°F)
    12.7 to 17.2 mΩ
    c-3 (PHC) - c-1 (PHA)
    25°C (77°F)
    12.7 to 17.2 mΩ
    c-1 (PHA) - Motor case
    Always
    10 kΩ or higher
    c-2 (PHB) - Motor case
    Always
    10 kΩ or higher
    c-3 (PHC) - Motor case
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Power Steering Motor Assembly



NG
REPLACE POWER STEERING MOTOR ASSEMBLY (Click here)
OK


3.READ VALUE USING INTELLIGENT TESTER (MOTOR VOLTAGE)
  1. Turn the power switch off.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (READY).

  1. Turn the intelligent tester on.

  1. Enter the following menus: Chassis / EMPS / Data List.

  1. Select the items "Motor Terminal Volt (U)", "Motor Terminal Volt (V)" and "Motor Terminal Volt (W)" in the Data List and read the value displayed on the intelligent tester.

    EMPS 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Motor Terminal Volt (U)
    Motor terminal voltage (A phase)/
    Min.: 0.000 V
    Max.: 98.000 V
    Value changes within 4 to 35 V range
    Power switch on (READY) and steering wheel being turned
    Motor Terminal Volt (V)
    Motor terminal voltage (B phase)/
    Min.: 0.000 V
    Max.: 98.000 V
    Value changes within 4 to 35 V range
    Power switch on (READY) and steering wheel being turned
    Motor Terminal Volt (W)
    Motor terminal voltage (C phase)/
    Min.: 0.000 V
    Max.: 98.000 V
    Value changes within 4 to 35 V range
    Power switch on (READY) and steering wheel being turned


Result 
Condition
Proceed to
During steering operation, value changes within 4 to 35 V range
A
During steering operation, voltage is not generated
B


B
REPLACE POWER STEERING MOTOR ASSEMBLY (Click here)
A

REPLACE POWER STEERING ECU ASSEMBLY (Click here)