Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM

LIGHTING SYSTEM > Back-up Light Circuit

for Preparation Click here


DESCRIPTION

The power management control ECU controls the back-up lights via the engine room junction block assembly.

WIRING DIAGRAM


E228416E01


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses and bulbs for circuits related to this system before performing the following inspection procedure.

1.CHECK DTC OUTPUT (HYBRID CONTROL SYSTEM)
  1. Check for DTCs (Click here).

    OK:
    Hybrid control system DTCs are not output.



NG
GO TO HYBRID CONTROL SYSTEM (Click here)
OK


2.CHECK ENGINE ROOM JUNCTION BLOCK ASSEMBLY
  1. Using a voltmeter, check the signal reading of the engine room junction block assembly (Click here)

    OK:
    Output signal reading is normal.



NG
INSPECT ENGINE ROOM JUNCTION BLOCK ASSEMBLY (RESULTS OF SIGNAL READING CHECK)
OK


3.CHECK HARNESS AND CONNECTOR (ENGINE ROOM JUNCTION BLOCK ASSEMBLY POWER SOURCE AND BODY GROUND)


  1. Remove the engine room junction block assembly from the engine room relay block and junction block assembly.


    E230000E04

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    A-1 (BATT) - Body ground
    Power switch off
    11 to 14 V
    B-1 (ALT) - Body ground
    Power switch off
    11 to 14 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1F-3 (GND1) - Body ground
    Always
    Below 1 Ω
    1G-4 (GND2) - Body ground
    Always
    Below 1 Ω


Text in Illustration 
*a
Component without engine room junction block assembly
(Engine Room Relay Block and Junction Block Assembly)
-
-


NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


4.CHECK HARNESS AND CONNECTOR (REAR LIGHT ASSEMBLY - ENGINE ROOM JUNCTION BLOCK ASSEMBLY)
  1. Disconnect the T7 rear light assembly LH connector and T1 rear light assembly RH connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    LH Side 
    Tester Connection
    Condition
    Specified Condition
    1M-1(BKLP) - T7-1(B)
    Always
    Below 1 Ω
    RH Side 
    Tester Connection
    Condition
    Specified Condition
    1M-1(BKLP) - T1-1(B)
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


5.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - ENGINE ROOM JUNCTION BLOCK ASSEMBLY)
  1. Disconnect the A38 power management control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1F-9(BLPS) - A38-15(BL)
    Always
    Below 1 Ω
    1F-9(BLPS) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


6.CHECK ENGINE ROOM JUNCTION BLOCK ASSEMBLY
  1. Replace the engine room junction block assembly with a new or a known good one (Click here).

    OK:
    The back-up lights operate normally.



NG
REPLACE POWER MANAGEMENT CONTROL ECU (Click here)
OK

END (ENGINE ROOM JUNCTION BLOCK ASSEMBLY WAS DEFECTIVE)