Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM

METER / GAUGE SYSTEM > Fuel Economy Meter Malfunction

for Preparation Click here


DESCRIPTION

The combination meter assembly communicates with the ECM and skid control ECU via the CAN communication system. The combination meter calculates the current fuel consumption based on a vehicle speed signal from the skid control ECU, a fuel injection signal from the ECM.

WIRING DIAGRAM


E224308E02


INSPECTION PROCEDURE

1.CHECK AND REPLACE CAN COMMUNICATION SYSTEM
  1. Check if CAN communication DTCs are output (Click here).

    Result:

    Result
    Proceed to
    DTCs are not output.
    A
    DTCs are output.
    B



B
GO TO CAN COMMUNICATION SYSTEM (Click here)
A


2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (FUEL CONSUMPTION METER OPERATION)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the intelligent tester on.

  1. Enter following menus: Body / Combination Meter / Active Test.

  1. Check the operation by referring to the table below.

    Combination Meter 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Fuel Consumption Meter Operation
    Fuel consumption meter
    MIN, 1/4, 1/2, 3/4, MAX
    -

    OK:
    Needle indication is normal.



NG
REPLACE COMBINATION METER ASSEMBLY (Click here)
OK


3.READ VALUE USING INTELLIGENT TESTER (VEHICLE SPEED, INJECTION VOLUM)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the intelligent tester on.

  1. Enter the following menus:

    1. for ABS/VSC/TRC: Chassis / ABS/VSC/TRC / Data List.

    2. for Engine and ECT: Powertrain / Engine and ECT / Data List.

  1. Check the values by referring to the table below.

    ABS/VSC/TRC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Vehicle Speed
    Vehicle speed/Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
    Vehicle stopped: 0 km/h (0 mph)
    When driving at constant speed: No large fluctuations

    Engine and ECT 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Injection Volum (Cylinder 1)
    Injection volume (cylinder 1)/Min.: 0 ml, Max.: 2.047 ml
    0 to 0.5 ml
    1. Stored as Freeze Frame Data
    2. This is the fuel injection volume for 10 injections.

    Result:

    Result
    Proceed to
    The data list values displayed on the intelligent tester are within the normal condition range.
    A
    The data list value displayed on the intelligent tester differs from the normal condition range. (ABS/VSC/TRC)
    B
    The data list value displayed on the intelligent tester differs from the normal condition range. (Engine and ECT w/o EGR System)
    C
    The data list value displayed on the intelligent tester differs from the normal condition range. (Engine and ECT w/ EGR System)
    D



B
GO TO BRAKE CONTROL SYSTEM (Click here)

C
GO TO SFI SYSTEM (Click here)

D
GO TO SFI SYSTEM (Click here)
A


4.REPLACE BRAKE BOOSTER ASSEMBLY
  1. Replace the brake booster assembly with a new or a known good one (Click here for LHD, Click here for RHD).

    Result:

    Result
    Proceed to
    The operation of the fuel economy meter does not return to normal.
    A
    The operation of the fuel economy meter returns to normal.
    B



B
END
A


5.REPLACE ECM
  1. Replace the ECM with a new or a known good one (Click here).


Result:

Result
Proceed to
The operation of the fuel economy meter does not return to normal.
A
The operation of the fuel economy meter returns to normal.
B



B
END
A

REPLACE COMBINATION METER ASSEMBLY (Click here)