Home › Engine / Hybrid System › 2AR-FXE ENGINE CONTROL › SFI SYSTEM (w/ EGR System)

DTC    P0403    Exhaust Gas Recirculation Control Circuit

for Preparation Click here


DESCRIPTION

Refer to DTC P0401 .

DTC No.
DTC Detection Condition
Trouble Area
P0403
Open or short in EGR valve circuit (1 trip detection logic).
  1. Open or short in EGR valve assembly circuit
  2. EGR valve assembly
  3. ECM

HINT:
DTC P0403 is stored when the power switch is on (IG).


MONITOR DESCRIPTION

This DTC is designed to detect an open or short in the EGR valve assembly circuit.
Example:
  1. If the EGR1, EGR2, EGR3 or EGR4 terminal output voltage is excessively low, but the step motor is still operating, the ECM determines that there is a short in the EGR valve assembly circuit, and stores the DTC.
  2. If the EGR1, EGR2, EGR3 or EGR4 terminal output voltage is excessively low, and the step motor is not operating, the ECM determines that there is an open in the EGR valve assembly circuit, and stores the DTC.

MONITOR STRATEGY


Frequency of Operation
Continuous

CONFIRMATION DRIVING PATTERN


A215251E08

  1. Connect the GTS to the DLC3.
  2. Turn the power switch on (IG).
  3. Turn the GTS on.
  4. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  5. Turn the power switch off and wait for at least 30 seconds.
  6. Turn the power switch on (IG) [A].
  7. Turn the GTS on.
  8. Put the engine in inspection mode (maintenance mode) (Click here).
  9. Start the engine and warm it up [B].
  10. Drive the vehicle at 20 km/h (12 mph) or more for 10 minutes [C].

    CAUTION:
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

  11. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [D].
  12. Read the pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  13. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  14. Input the DTC: P0403.
  15. Check the DTC judgment result.

    GTS Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system has a normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.


WIRING DIAGRAM


A315305E01


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.PERFORM ACTIVE TEST USING GTS (CONTROL THE EGR STEP POSITION)
  1. Connect the GTS to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the GTS on.

  1. Put the engine in inspection mode (maintenance mode) (Click here).

  1. Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.

    HINT:
    The A/C switch and all accessory switches should be off.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the EGR Step Position / Data List / All Data / MAP and Throttle Idle Position.

  1. Confirm that Throttle Idle Position is ON and check the MAP value in the Data List while performing the Active Test.

    HINT:
    1. Do not leave the EGR valve open for 10 seconds or more during the Active Test.
    2. Be sure to return the EGR valve to step 0 when the Active Test is completed.
    3. Do not open the EGR valve 30 steps or more during the Active Test.

    OK:
    MAP change in response to EGR step position when Throttle Idle Position is ON in the Data List.


    Standard:

    -
    EGR Step Position (Active Test)
    0 Steps
    0 to 30 Steps
    MAP
    (Data List)
    (EGR valve is fully closed)
    MAP value is at least +10 kPa (75 mmHg) higher than when EGR valve is fully closed

    HINT:
    1. While performing the Active Test, if the increase in the value of MAP is small, the EGR valve assembly may be a malfunctioning.
    2. Even if the EGR valve assembly is malfunctioning, rough idling or an increase in the value of MAP may occur while performing the Active Test. However, the amount that the value of MAP increases will be smaller than normal.



NG
Go to step 2
OK

CHECK FOR INTERMITTENT PROBLEMS (Click here)  

2.INSPECT EGR VALVE ASSEMBLY
  1. Inspect the EGR valve assembly (Click here).

    HINT:
    Perform "Inspection After Repair" after replacing the EGR valve assembly (Click here).



NG
REPLACE EGR VALVE ASSEMBLY (Click here)
OK


3.CHECK TERMINAL VOLTAGE (POWER SOURCE OF EGR VALVE ASSEMBLY)


    A209148E15
  1. Disconnect the EGR valve assembly connector.

  1. Turn the power switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    E24-2 (+B1) - Body ground
    Power switch on (IG)
    11 to 14 V
    E24-5 (+B2) - Body ground
    Power switch on (IG)
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to EGR Valve Assembly)



NG
Go to step 5
OK


4.CHECK HARNESS AND CONNECTOR (EGR VALVE ASSEMBLY - ECM)
  1. Disconnect the EGR valve assembly connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    E24-4 (EGR1) - E28-28 (EGR1)
    Always
    Below 1 Ω
    E24-3 (EGR2) - E28-27 (EGR2)
    Always
    Below 1 Ω
    E24-6 (EGR3) - E28-26 (EGR3)
    Always
    Below 1 Ω
    E24-1 (EGR4) - E28-25 (EGR4)
    Always
    Below 1 Ω
    E24-4 (EGR1) or E28-28 (EGR1) - Body ground
    Always
    10 kΩ or higher
    E24-3 (EGR2) or E28-27 (EGR2) - Body ground
    Always
    10 kΩ or higher
    E24-6 (EGR3) or E28-26 (EGR3) - Body ground
    Always
    10 kΩ or higher
    E24-1 (EGR4) or E28-25 (EGR4) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)  

5.CHECK HARNESS AND CONNECTOR (EGR VALVE ASSEMBLY - NO. 1 INTEGRATION RELAY)
  1. Disconnect the EGR valve assembly connector.

  1. Remove the No. 1 integration relay from the engine room relay block and junction block assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    E24-2 (+B1) - 1A-8
    Always
    Below 1 Ω
    E24-5 (+B2) - 1A-8
    Always
    Below 1 Ω
    E24-2 (+B1) or 1A-8 - Body ground
    Always
    10 kΩ or higher
    E24-5 (+B2) or 1A-8 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE NO. 1 INTEGRATION RELAY (Click here)