Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM

DTC    B15C3    Speaker Output Short

for Preparation Click here


DESCRIPTION

This DTC is stored when a malfunction occurs in the speakers.

DTC No.
DTC Detection Condition
Trouble Area
B15C3
A short is detected in the speaker output circuit
  1. Harness or connector
  2. Speaker
  3. Radio and display receiver assembly

WIRING DIAGRAM


E226481E31


INSPECTION PROCEDURE

1.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - BODY GROUND)
  1. Disconnect the I152 and I153 radio and display receiver assembly connectors.

  1. Disconnect the I83 and I1 front No. 2 speaker assembly connectors.

  1. Disconnect the O18 and O21 rear speaker assembly connectors.

  1. Measure the resistance between the radio and display receiver assembly and body ground to check for a short circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I152-1 (FR+) - Body ground
    Always
    10 kΩ or higher
    I152-5 (FR-) - Body ground
    Always
    10 kΩ or higher
    I152-2 (FL+) - Body ground
    Always
    10 kΩ or higher
    I152-6 (FL-) - Body ground
    Always
    10 kΩ or higher
    I153-1 (RR+) - Body ground
    Always
    10 kΩ or higher
    I153-3 (RR-) - Body ground
    Always
    10 kΩ or higher
    I153-2 (RL+) - Body ground
    Always
    10 kΩ or higher
    I153-6 (RL-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.CHECK HARNESS AND CONNECTOR (FRONT NO. 2 SPEAKER ASSEMBLY - BODY GROUND)
  1. Disconnect the J5 and K5 front No. 1 speaker assembly connectors.

  1. Disconnect the I83 and I1 front No. 2 speaker assembly connectors.

  1. Measure the resistance between each of the front No. 2 speaker assemblies and body ground to check for a short circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I83-3 (+) - Body ground
    Always
    10 kΩ or higher
    I83-1 (-) - Body ground
    Always
    10 kΩ or higher
    I1-3 (+) - Body ground
    Always
    10 kΩ or higher
    I1-1 (-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.INSPECT FRONT NO. 1 SPEAKER ASSEMBLY
  1. Remove the front No. 1 speaker assembly (Click here).



    E289189E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Always
    3.2 to 4.8 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Front No. 1 Speaker Assembly)



NG
REPLACE FRONT NO. 1 SPEAKER ASSEMBLY (Click here)
OK


4.INSPECT FRONT NO. 2 SPEAKER ASSEMBLY
  1. Remove the front No. 2 speaker assembly (Click here).



    E226097E51
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    2 (TWR-) - 4 (TWR+)
    Always
    10 kΩ or higher
    1 (-) - 2 (TWR-)
    Always
    Below 1 Ω
    3 (+) - 4 (TWR+)
    Always
    Below 1 Ω
    2 (TWL-) - 4 (TWL+)
    Always
    10 kΩ or higher
    1 (-) - 2 (TWL-)
    Always
    Below 1 Ω
    3 (+) - 4 (TWL+)
    Always
    Below 1 Ω

    Text in Illustration 
    *A
    for RH
    *B
    for LH
    *a
    Component without harness connected
    (Front No. 2 Speaker Assembly)



NG
REPLACE FRONT NO. 2 SPEAKER ASSEMBLY (Click here)
OK


5.REPLACE FRONT NO. 2 SPEAKER ASSEMBLY
  1. Replace the front No. 2 speaker assembly with a new or known good one (Click here).

  1. Clear the DTCs (Click here).

  1. Recheck for DTCs and check that no DTCs are output.

    OK:
    No DTCs are output.

    HINT:
    1. Connect all the connectors to the front No. 2 speaker assemblies that were disconnected.
    2. When there is a possibility that either the right or left front No. 2 speaker assembly is defective, inspect by interchanging the right one with the left one.
    3. Perform the above inspection on both the LH and RH side.



NG
Go to step 6
OK

END 

6.INSPECT REAR SPEAKER ASSEMBLY
  1. Remove the rear speaker assembly (Click here).



    E289189E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Always
    3.2 to 4.8 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Rear Speaker Assembly)



NG
REPLACE REAR SPEAKER ASSEMBLY (Click here)
OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY (Click here)